- Users - lists.chirpmyradio.com

[chirp_users] unsubscribe me please
by n6rsr＠cox.net 06 May '14

06 May '14

please remove me from your subscription. n6rsr

2 1

[chirp_users] Anytone 3318
by MCH 06 May '14

06 May '14

Any idea when/if chirp will support the Anytone AT-3318A that has the channel groups? Joe M.

2 2

[chirp_users] Suggestions for mag-mount dual-band antenna
by Pete Miller 06 May '14

06 May '14

I'd appreciate suggestions from Baofeng users about mag-mount dual-band 2m / 70cm antennas that are working well. Of course a perfect antenna will be a great find, but if I have to prioritize, these will do: * One choice >$60, one choice $60-$120 * Zero or minimal scratching * Perfect retention at air speeds <80 mph * 2m probably slightly higher priority * Receiving probably slightly higher priority for now * At least good transmitting My unit is a UV-5RE Plus. Thanks.

6 9

[chirp_users] Icom V82
by John KB2SCS 04 May '14

04 May '14

Hi All I am using Chirp on Puppy Linux Slacko (Slackware) I am using the source code of Chirp. In Slacko I have the full Python development system. The only other thing I had to install to get Chirp to work was Python Serial. I started up Chirp by typing into the terminal window chirpw. I was able to down load the image of my IcomV82 into Chirp. I noticed on the Repeater2 column that the callsign was W2DNY C. Is this normal? Shouldn't the C be a G? I clicked on the WD2NY C in the Repeater2 column and a drop down list opened which only contained WD2NY C and the other repeater callsigns that I have programed into my radio. All the callsigns had a C at the end none with a G at the end. These Callsigns are in my Repeater1 column which a C makes sense. Again shouldn't the Repeater2 callsings have a G for gateway. The memories in the radio for Repeater2 all have a G in them. It looks like Chirp did not read the repeater2 memories of the radio correctly. Any help in this matter will be greatly appreciated. Thank you for your time in reading this E-Mail. -- Let us hope we never witness the "Silence Of The Hams" 73 DE John KB2SCS Packet: KB2SCS(a)WA2PNU,#NLI.NY.USA.NOAM E-Mail: kb2scs(a)arrl.net Web Page: http://www.qsl.net/kb2scs

1 0

[chirp_users] Anyone experienced using the scramble mode with the wouxun models?
by I'm a Ham! 03 May '14

03 May '14

I have a Wouxun 920-p-a and wanted to buy the wouxun HT's that have the scramble mode. Has anyone used them at all? Robert KK4SEY

2 1

Re: [chirp_users] Need info on Motorola XTN XU2600 radio
by Kevin Zembower 03 May '14

03 May '14

On 05/03/2014 07:40 AM, Jim Unroe wrote: > Kevin, > > Assuming that 67.0 Hz is the CTCSS tone used by the Motorola radios, > you have 2 choices for programming the BF-888S radios. But before we > get started, you should click "View" in the CHIRP menu bar and then in > the drop down menu, enable "Hide Unused Fields". > > Method 1: > > This method will transmit the 67.0 Hz CTCSS tone that is required to > open the squelch on the Motorola radios. It leaves the BF-888S squelch > as carrier operated. It won't matter if the transmitting station is > using CTCSS or not. > > Tone Mode = Tone > Tone = 67.0 > ToneSql = unused (88.5 or blank if "Hide Unused Fields" is enabled) Jim, thank you so much. Your Method 1 worked like a champ, so I never even tried Method 2. > Be sure to let you son's principal (or better yet, the person that is > responsible for the license that gives them the authority to transmit > on the frequencies that you are programming) know that these radios > aren't certified for part 90 use under the FCC rules. Their use for > this purpose would not be permitted. Thanks, also, for this warning. It never even occurred to me that reprogramming these radios might be illegal. I'll pass this one. Do you know of any pointers to documents on the Web that might be useful to read concerning this issue? Thanks, again, for your excellent help and advice. Have a good day. -Kevin > > Jim KC9HI > > > On Fri, May 2, 2014 at 9:48 PM, Kevin Zembower <kzembower(a)verizon.net > <mailto:kzembower@verizon.net>> wrote: > > Hello, I just joined this group, after downloading and using CHIRP. > Thank you all for a very helpful application. > > The principal at my son's school asked for my help. They have a number > of Motorola XTN XU2600 radios, that they'd like to gradually replace > with Baofeng BF-888S ones. I'm trying to use CHIRP to program the > Baofeng radios so that they interoperate with the Motorola ones, using > the same channel numbers. > > I was able to run CHIRP and successfully downloaded the settings from > the Baofeng. However, I don't have a programming cable for the > Motorola, > and the Baofeng one doesn't fit. I changed the frequencies in the > Baofeng to match the UHF frequencies I found in the Motorola user's > manual, but the radios don't communicate. I left all the other columns > unchanged. > > Subsequently, I changed the 'TONE Mode' to 'None' for all the > channels. > I then noticed that the Baofeng could receive on channel 1 when I > transmitted on the Motorola on channel one, but the Motorola couldn't > receive from the Baofeng. > > I believe that I need all the information for all the columns to > get the > Baofeng working with the Motorola. Can anyone point me to a CHIRP .img > file or a .cvs file for the Motorola XTN XU2600? I'd be happy to > send my > factory-default Baofeng BF-888S .img file to anyone, or to a > repository, > for future reference. Is the Motorola set up to use any of the stock > configs? > > This is what I have programmed in the Baofeng for channel 1: > Freq: 464.500000 > Tone mode: none > Tone: 88.5 > ToneSql: 69.3 > DTCS Code: 023 > DTCS Rx Code: 023 > DTCS Pol: NN > Cross Mode: Tone->Tone > Duplex: none > Offset: 0.0 > Mode: FM > Power: High > Skip: S > > Thank you for any advice or guidance you can give me. Thank, > again, for > such a useful program. > > -Kevin > > _______________________________________________ > chirp_users mailing list > chirp_users(a)intrepid.danplanet.com > <mailto:chirp_users@intrepid.danplanet.com> > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > >

2 2

[chirp_users] Wouxun KGUV8D and KGUV950P
by david johns 03 May '14

03 May '14

Hi Guys, has anyone got the Wouxun KGUV8D and KGUV950P details worked out for chirp yet. I use chirp for my baofengs and would love to have all my radios working on chirp. Hopefully one of you gurus out there could program these in???? Thanks in advance

3 3

[chirp_users] Need info on Motorola XTN XU2600 radio
by Kevin Zembower 02 May '14

02 May '14

Hello, I just joined this group, after downloading and using CHIRP. Thank you all for a very helpful application. The principal at my son's school asked for my help. They have a number of Motorola XTN XU2600 radios, that they'd like to gradually replace with Baofeng BF-888S ones. I'm trying to use CHIRP to program the Baofeng radios so that they interoperate with the Motorola ones, using the same channel numbers. I was able to run CHIRP and successfully downloaded the settings from the Baofeng. However, I don't have a programming cable for the Motorola, and the Baofeng one doesn't fit. I changed the frequencies in the Baofeng to match the UHF frequencies I found in the Motorola user's manual, but the radios don't communicate. I left all the other columns unchanged. Subsequently, I changed the 'TONE Mode' to 'None' for all the channels. I then noticed that the Baofeng could receive on channel 1 when I transmitted on the Motorola on channel one, but the Motorola couldn't receive from the Baofeng. I believe that I need all the information for all the columns to get the Baofeng working with the Motorola. Can anyone point me to a CHIRP .img file or a .cvs file for the Motorola XTN XU2600? I'd be happy to send my factory-default Baofeng BF-888S .img file to anyone, or to a repository, for future reference. Is the Motorola set up to use any of the stock configs? This is what I have programmed in the Baofeng for channel 1: Freq: 464.500000 Tone mode: none Tone: 88.5 ToneSql: 69.3 DTCS Code: 023 DTCS Rx Code: 023 DTCS Pol: NN Cross Mode: Tone->Tone Duplex: none Offset: 0.0 Mode: FM Power: High Skip: S Thank you for any advice or guidance you can give me. Thank, again, for such a useful program. -Kevin

1 1

[chirp_users] Additional data source
by Mark Lewis GW7KDU 02 May '14

02 May '14

To CHIRP developers I would like to propose a new data source to add to Chirp. The UK has large number of analogue and digital amateur repeaters. These are managed (for licensing purposes) by an RSGB committee, the ETCC (of which I am the secretary). We maintain a website of all UK repeaters on http://www.ukrepeater.net/ and are interested in providing an additional data source similar to repeaterbook. If you are interested we need a contact to discuss data formats etc. 73 Mark GW7KDU gw7kdu(a)rmcwales.org.uk

1 0

[chirp_users] New model request -- Yaesu FT-2900R
by Marino Duregon 02 May '14

02 May '14

To Dan Smith, I live in the Portland, OR area and in a couple of weeks I should be able to lend my FT-2900R to you or someother developer in the area. Let me know. Marino KG7EMV -- Marino Duregon kg7emv(a)arrl.net

1 0

[chirp_users] New Daily Build
by Build System 28 Apr '14

28 Apr '14

Greetings, A new daily build of CHIRP is available. This includes changes made directly to the tree yesterday, and may include additional features, bug fixes, and/or bugs. If you are interested in trying it, grab it from the following location: http://trac.chirp.danplanet.com/chirp_daily/daily-20140428 A list of the changes included in this build (since the last daily) follows: Changes for Build #272 [Dan Drogichen <chirp.cordless(a)xoxy.net>] [FT-60] The implementation of memory skip is incorrect. - Fixes #1557 - Change flags[500] to skipflags[250]. The memory offset is unchanged. The name change is in anticipation of bankflags[] being added, and to avoid confusion with an unrelated variable in the file named flags. - Index skipflags[] with [memory - 1] rather than [memory]. - Reverse the order of both the elements of skipflags[] and the non-zero elements of SKIPS[]. [Marco Filippi <iz3gme.marco(a)gmail.com>] [BF-888] Fix BCL and Scramble editing BCL and Scramble was always enabled on edited memories because setting.values is of <type 'instance'> so not setting.values as well as not(bool(setting.values)) always return false, coerce to int instead pickup the value of the instance so not(int(setting.values)) do the job Fix #1549

1 0

Re: [chirp_users] Programming separate receive and transmit PL
by robbknyc 27 Apr '14

27 Apr '14

Thanks Jim. Sent from my Verizon Wireless 4G LTE smartphone -------- Original message -------- From: Jim Unroe <rock.unroe(a)gmail.com> Date:04/27/2014 10:10 AM (GMT-05:00) To: Discussion of CHIRP <chirp_users(a)intrepid.danplanet.com> Subject: Re: [chirp_users] Programming separate receive and transmit PL Rob, The first thing you should do is click View in the menu bar and enable "Hide Unused Fields" The next thing would be to review the CHIRP guide available from the miklor.com website and the Memory Editor Columns page available on the CHIRP website. http://www.miklor.com/COM/UV_CHIRP5R.php http://chirp.danplanet.com/projects/chirp/wiki/MemoryEditorColumns On Sun, Apr 27, 2014 at 9:30 AM, Rob <robbknyc(a)hotmail.com> wrote: > > Hi, > > I just picked up a Baofeng GT-3 and downloaded Chirp to use with it. > > I have a programming question on how to program separate receive and > transmit PLs. > > How would I program something with say a receive frequency of 150.0000 and > a PL of 77.0 and a transmit frequency of say155.0000 and a PL of 118.8. > > Here are the settings I'm using: > > Under frequency I placed the receive frequency of 150.0000. > Correct > > Tone mode is set to tone. > This only sets up a TX tone. When Tone Mode is set to Tone, the ToneSQL column and the Cross Mode columns are ignored. Tone Mode should be set to Cross to enable the Cross Mode settings. > > Tone and tone SQL is the 77.0 receive PL. > Tone should be set to 118.8 ToneSQL should be set to 77.0 DTCS code and Rx code is 023. > These columns should be left at their defaults since they will be ignored and should no longer display once the Cross Mode is set. > > Cross mode is tone > tone. > Correct. > > Duplex is split. > Duplex should be set to "(None)" (which is RX=TX=simplex) > > Offset is the transmit frequency of 155.0000. > Offset will be unused and therefor should be blank > > Mode is FM. Power is high. > > How do I set that transmit PL of 118.8? > > Thanks in advance. > > R... > > Jim KC9HI _______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users

1 0

[chirp_users] Programming separate receive and transmit PL
by Rob 27 Apr '14

27 Apr '14

Hi, I just picked up a Baofeng GT-3 and downloaded Chirp to use with it. I have a programming question on how to program separate receive and transmit PLs. How would I program something with say a receive frequency of 150.0000 and a PL of 77.0 and a transmit frequency of say155.0000 and a PL of 118.8. Here are the settings I'm using: Under frequency I placed the receive frequency of 150.0000. Tone mode is set to tone. Tone and tone SQL is the 77.0 receive PL. DTCS code and Rx code is 023. Cross mode is tone > tone. Duplex is split. Offset is the transmit frequency of 155.0000. Mode is FM. Power is high. How do I set that transmit PL of 118.8? Thanks in advance. R...

2 1

[chirp_users] Chirp 0.4.0 and IC-91A on OS X
by Horace Posadas 26 Apr '14

26 Apr '14

Hello, I’ve tried searching the archives, but have not been able to find any answers. Here’s what I have: Radio: Icom IC-91A Cable: OPC1529R (made by Icom) FTDI USB to Serial made by Tripplite When I try to download the frequencies from the radio, everything comes up as “ERROR”. I was able to use the same FTDI cable to download and program my Yaesu FT-60R. So I know that the USB-to-Serial cable works. I’m running CHIRP 0.4.0 on a Macbook Pro on Mac OS X 10.9.2. Did I miss something? Thanks and 73, KI6EEX

2 1

[chirp_users] WHOA! Stop the bus!
by Milton 26 Apr '14

26 Apr '14

I just spent an interesting 4 hours. This morning my windows machine would not wake up from sleep. Every night when I'm done with it I hit the crescent moon on the Logitech keyboard and some things take place and after 30 seconds it's bed time. Light out except the power LED blinks on and off, Well this AM after a 7 hour sleep it was time to start up. As usual it took a push on the space bar and within 10 seconds I was ready to rock and roll. Well that didn't happen this morning. Space, zero. Shake the mouse, zero. Power light blink blink blink as usual while sleeping so I reached around to the back and flipped the power supply switch off. Ok no more blinking. So I press the on button and GASP! He's dead Jim. Zilch, zero nothing. I pull the side cover off and the motherboard voltage LED is lit. I remove the CMOS battery short the leads out and replace the battery, Still dead. Ok so I probably have a toasted voltage distro on the motherboard. Also, all my USB sockets are missing 5 volts. Before when I shut the power off, not just sleep, the USB ports kept up juice to charge stuff. So mobo 5 volt led is it, no 5 volts getting out the USB = x-eyed mobo. This isa 4 year old Asus top of the line then for the AMD Phenom II quad core processor running 3/6 GHZ per core with Corsair DDR3 memory nd a high performance EVGA GeoForce video. All rock solid stuff powered by a 650 watt PSU. And to make a long story even longer, This PC had most of my recent programming data on it. So my only recourse is to break out the Macbook that has had a cooling fan problem nd been store for a couple months. However when I fired the Mac up she came to life and was going to make sure All three prolific cables still worked. Fist up, Baofeng. TX don and RX up no problem. Next was the Prolific with a mini DIN 6 grafted i=on the end that worked fabulously in Win 7. Plugged in the Mac, see the port, set the FT8900 in TX clone and downloads fine. After that to get it to uplood what it downloaded you simply do your thing in Chirp to upload and while still in CLONE in the FT8900 just hit the LOW button. Done this many time using Windows 7. However this time in Chirp the just released Mavericks 10.9.1 update the upload puked after 5 seconds leaving me a bricked FT8900. When I powered off the FT8900 the entire LED segments lit up. Both sides showed vfo mode and the TX indicators were fully deflected even though nothing was transmitting. Lucky for me a reset all fixed me up. So, I break out the Dell 910 netbook, install the 3.2.0.0 cable driver and Chirp 4. Transferred the .img file I luckily (smartly actually) downloaded from the FT8900 back to the FT8900. I could not do that in Mavericks 10.9.2, all I got when writing was a cable error, couldn't right block this or that, Bad Cable ? Well BS bad cable it worked fine in Windows 7 with 3.2.2.0. Anyway I'm pissed off. And I deserve it. It hasn't been a good day for me but I got the FT8900 back the way it was.

1 0

[chirp_users] NC Hams using chirp
by Dwayne 22 Apr '14

22 Apr '14

Any hams in the Raleigh NC area that are using chirp (preferably with Icom 92ad) that could help me troubleshoot why I can't program the IC-92ad? Dwayne

7 15

Re: [chirp_users] Alinco DJ-X10
by raymond reese 21 Apr '14

21 Apr '14

Has anyone considered Chirp support for the Alinco DJ-X10T scanning receiver?

1 0

[chirp_users] Baofeng UV-6 -- Radio refused clone
by Aubrey Turner 20 Apr '14

20 Apr '14

I have a brand new UV-6 that I just received that won't allow me to perform a download. It gives a "Radio refused clone" error. I have a known working cable. It's a Prolific "clone" but I know it works as I have used it on this computer and several others to program several different UV-5R's. I am using Ubuntu 13.10 with the latest daily build (20140413). The cable shows up on /dev/ttyUSB0 and my ID is a member of the dialout group (as I mentioned, I've used this combination of computer and cable with the UV-5R). What happens is that it appears to be communicating initially to get the ident, but it gets a zero back for the 'ack' afterwards instead of the expected value of "\x06". At least that's what I'm gathering from reading the code. I've got years of experience as a developer, but only know enough Python to follow the broad outline of what is taking place (perhaps this will be my excuse to finally learn Python). I was able, though, to add a line of code to dump the ack value, which is how I found that it's zero. I just wanted to check to see if anyone had seen this or knew of something I might be missing before I troubled the developers by opening a ticket. Here is the output I'm getting (from stdout, as it doesn't seem to be creating a debug.log anywhere): (includes my extra line of output) turnera@runabout:~/Downloads/CHIRP/chirp-daily-20140413$ ./chirpw CHIRP daily-20140413 on Linux - Ubuntu 13.10 (Python 2.7.5+) (process:29928): Gtk-WARNING **: Locale not supported by C library. Using the fallback 'C' locale. Registered Icom_IC-2820H = IC2820Radio Registered Yaesu_VX-8_R = VX8Radio Registered Yaesu_VX-8_DR = VX8DRadio Registered Yaesu_VX-8_GE = VX8GERadio Registered Puxing_PX-777 = Puxing777Radio Registered Puxing_PX-2R = Puxing2RRadio Registered Generic_CSV = CSVRadio Registered Commander_KG-UV = CommanderCSVRadio Registered RT_Systems_CSV = RTCSVRadio Registered Icom_IC-2100H = IC2100Radio Registered Yaesu_FTM-350 = FTM350Radio Registered Icom_ID-800H_v2 = ID800v2Radio Registered TYT_TH-UV3R = TYTUV3RRadio Registered Yaesu_FT-7800_7900 = FT7800Radio Registered Yaesu_FT-8800 = FT8800Radio Registered Yaesu_FT-8900 = FT8900Radio Registered Yaesu_VX-170 = VX170Radio Registered Yaesu_VX-7 = VX7Radio Registered Icom_IC-208H = IC208Radio Registered Yaesu_VX-6 = VX6Radio Registered Baofeng_UV-B5 = BaofengUVB5 Registered Icom_IC-91_92AD_ICF_File = IC9xICFRadio Registered Icom_IC-V82_U82 = ICx8xRadio Registered Yaesu_VX-3 = VX3Radio Registered Icom_IC-2200H = IC2200Radio Registered Icom_7200 = Icom7200Radio Registered Icom_7000 = Icom7000Radio Registered Icom_746 = Icom746Radio Registered Icom_IC-T70 = ICT70Radio Registered KYD_NC-630A = NC630aRadio Registered Kenwood_TK-7102 = KenwoodTK7102Radio Registered Kenwood_TK-8102 = KenwoodTK8102Radio Registered Kenwood_TK-7108 = KenwoodTK7108Radio Registered Kenwood_TK-8108 = KenwoodTK8108Radio Registered Baofeng_UV-5R = BaofengUV5R Registered Baofeng_F-11 = BaofengF11Radio Registered Baofeng_UV-82 = BaofengUV82Radio Registered Baofeng_UV-6 = BaofengUV6Radio Registered Intek_KT-980HP = IntekKT980Radio Registered Baofeng_UV-3R = UV3RRadio Registered Icom_IC-91_92AD = IC9xRadio Registered Yaesu_FT-60 = FT60Radio Registered Icom_ID-31A = ID31Radio Registered Yaesu_FT-817 = FT817Radio Registered Yaesu_FT-817ND = FT817NDRadio Registered Yaesu_FT-817ND_US = FT817NDUSRadio Registered TYT_TH-UVF1 = TYTTHUVF1Radio Registered Generic_XML = XMLRadio Registered AnyTone_5888UV = AnyTone5888UVRadio Registered Intek_HR-2040 = IntekHR2040Radio Registered Polmar_DB-50M = PolmarDB50MRadio Registered Powerwerx_DB-750X = PowerwerxDB750XRadio Registered Yaesu_VX-2 = VX2Radio Registered Yaesu_FT-2800M = FT2800Radio Registered Icom_ID-51A = ID51Radio Registered Icom_ID-880H = ID880Radio Registered Icom_ID-80H = ID80Radio Registered Icom_IC-T7H = ICT7HRadio Registered Vertex_Standard_VXA-700 = VXA700Radio Registered Icom_IC-Q7A = ICQ7Radio Registered Icom_IC-T8A = ICT8ARadio Registered Yaesu_VX-5 = VX5Radio Registered Yaesu_FT-1802M = FT1802Radio Registered Icom_IC-2720H = IC2720Radio Registered Wouxun_KG-UVD1P = KGUVD1PRadio Registered Wouxun_KG-UV6 = KGUV6DRadio Registered Wouxun_KG-816 = KG816Radio Registered Wouxun_KG-818 = KG818Radio Registered Icom_IC-W32A = ICW32ARadio Registered Kenwood_HMK = HMKRadio Registered Alinco_DR03T = DR03Radio Registered Alinco_DR06T = DR06Radio Registered Alinco_DR135T = DR135Radio Registered Alinco_DR235T = DR235Radio Registered Alinco_DR435T = DR435Radio Registered Alinco_DJ596 = DJ596Radio Registered Jetstream_JT220M = JT220MRadio Registered Alinco_DJ175 = DJ175Radio Registered Kenwood_TH-D72_clone_mode = THD72Radio Registered Kenwood_ITM = ITMRadio Registered Baojie_BJ-UV55 = BaojieBJUV55Radio Registered Yaesu_FT-90 = FT90Radio Registered Baofeng_BF-888 = H777Radio Registered Kenwood_TH-D7 = THD7Radio Registered Kenwood_TH-D7G = THD7GRadio Registered Kenwood_TM-D700 = TMD700Radio Registered Kenwood_TM-V7 = TMV7Radio Registered Kenwood_TM-G707 = TMG707Radio Registered Kenwood_TH-G71 = THG71Radio Registered Kenwood_TH-F6 = THF6ARadio Registered Kenwood_TH-F7 = THF7ERadio Registered Kenwood_TM-D710 = TMD710Radio Registered Kenwood_TH-D72_live_mode = THD72Radio Registered Kenwood_TM-V71 = TMV71Radio Registered Kenwood_TH-K2 = THK2Radio Registered Kenwood_TM-271 = TM271Radio Registered Kenwood_TM-281 = TM281Radio Registered Kenwood_TM-471 = TM471Radio Registered ARRL_Travel_Plus = TpeRadio Registered Yaesu_FT-857_897 = FT857Radio Registered Yaesu_FT-857_897_US = FT857USRadio Registered TYT_TH-UVF8D = TYTUVF8DRadio Skipping existing stock config Skipping existing stock config Skipping existing stock config Skipping existing stock config Skipping existing stock config Skipping existing stock config Skipping existing stock config Skipping existing stock config User selected Baofeng UV-6 on port /dev/ttyUSB0 Clone thread started Sending Magic: 000: 50 bb ff 20 12 08 23 00 P.....#. Ident: 000: aa 01 01 36 01 74 01 04 ...6.t.. Ack: 000: 00 00 00 00 00 00 00 00 ........ Radio refused clone -- Exception: -- Traceback (most recent call last): File "/home/turnera/Downloads/CHIRP/chirp-daily-20140413/chirpui/clone.py", line 227, in run self.__radio.sync_in() File "/home/turnera/Downloads/CHIRP/chirp-daily-20140413/chirp/uv5r.py", line 619, in sync_in self._mmap = _do_download(self) File "/home/turnera/Downloads/CHIRP/chirp-daily-20140413/chirp/uv5r.py", line 450, in _do_download data = _ident_radio(radio) File "/home/turnera/Downloads/CHIRP/chirp-daily-20140413/chirp/uv5r.py", line 446, in _ident_radio raise error RadioError: Radio refused clone ------ Clone failed: Radio refused clone Clone thread ended --- Exception Dialog: Radio refused clone --- None ---------------------------- turnera@runabout:~/Downloads/CHIRP/chirp-daily-20140413$

4 10

[chirp_users] IC92AD issues
by Dwayne 20 Apr '14

20 Apr '14

I have a ic-92ad submersible with the waterproof mic/data connector on top of the radio. To program the radio I have the opc-1797 cable connected to the radio and then a USB cable (opc-478) with a 3.5mm plug that I purchased from KJ6ZWL that uses a FTDI chip. The cable drivers installed correctly. I'm using the latest version of chirp. But I just can't get the radio to talk to the chirp software. When I tell chirp to "download from radio" it comes up with 0.0000 under frequency and error under name for every location in the radio. If I type in a frequency and name for a location in chirp it doesn't update the radio. I tried to find a way to search the mailing list archives but couldn't find one. I have manually gone through all of the emails from the chirp list dealing with the IC92AD. Nothing in the emails seem to help me getting chirp and my IC92AD talking. What am I doing wrong? Dwayne

2 2

[chirp_users] UV-5r Serial Protocol & Commands
by Tom Sayles 20 Apr '14

20 Apr '14

Can anyone point me to public (or share their personal) documentation on the serial protocol and commands supported by the Baofeng UV-5r? I'm interested in seeing if real time (or near real time) software control of a UV-5r is practical. Basically, I'd like to setup a Raspberry Pi, some additional hardware [custom shield] and an Ethernet connection [w/ PoE?] that could plug-n-play with a UV-5r that to provide a remote [tower top?] back end to a soft [chirp based?] front end on my Linux desktop or android smart phone. -- Tom Sayles KE4HET Fall City, Wa, USA

4 3

[chirp_users] CHIRP live CD
by Roberto Gomez 19 Apr '14

19 Apr '14

Hi, I just tried to use the CHIRP live CD, made a bootable USB with Unetbootin, but it doesn’t boot on my Mac. Looks complicated to make this thing bootable. Any other options? Roberto

3 2

[chirp_users] FT-2800M info request
by James Williams 18 Apr '14

18 Apr '14

Just checking to find out if anyone has experience programming an FT-2800M with Chirp thru the microphone rj plugin?..de KB3KVA James

2 1

Re: [chirp_users] Comcast bouncing Chirp mail
by n1bgg＠comcast.net 18 Apr '14

18 Apr '14

Mine also Jack Callahan. N1BGG Emergency Coordinator GM-ARES 375 Manchester St #2F Manchester, NH 03103 Cell : 603-289-3524 Email: n1bgg(a)gm-ares.net Web: (local) www.gm-ares.net Web (state) www.nh-ares.org "If it can happen it will" "Semper Paratus"

3 2

[chirp_users] Comcast bouncing Chirp mail
by rtsears＠comcast.net 18 Apr '14

18 Apr '14

Is all of Comcast bouncing the Chirp mailing list or just me? Today was the second time in I swear less than a week my membership was suspended because of too many bounced messages.

3 2

[chirp_users] VX 170 troubles
by Roberto Gomez 18 Apr '14

18 Apr '14

Hello, Thanks for the help. I installed the generic driver but still have the same trouble. Also tried the NoZap driver, same. Generic driver is listed in kextstat on Terminal, 145 0 0xffffff7f82514000 0xa000 0xa000 net.sourceforge.osx-pl2303 (1.0.1) <112 34 5 4 3> I tried to check CHIRP log in terminal but couldn’t get it to work. Maybe my cable is no good? Its a Maxton RPC-Y7R-U so is based on a Prolific chip from what I can figure out. Thanks, Roberto

4 4

[chirp_users] Wiindows Vista problem
by Rick Hanzlik 18 Apr '14

18 Apr '14

I'm using the latest daily build for chirp to program my boafang u5r and b5. I have the altest usb driver installed but when I connect the radio and turn it on, the radio immediately goes into the transmit mode. I can use the same download and cable on my windows XP machine with no problem. Any suggestions? Rick Hanzlik N7NGK Sandy, Ut

3 2

[chirp_users] Baofeng UV-5R
by Rick Craft 17 Apr '14

17 Apr '14

Wondering how to *remove* the Reverse feature in Channel Mode, by short pressing the * key, on a Baofeng UV-5R, using Chirp 0.4.0. Enabling Dual Watch doesn't seem to do it. Thanks

3 2

[chirp_users] VX 170 programming
by Roberto Gomez 17 Apr '14

17 Apr '14

Hello, I’m trying to connect a VX 170 to CHIRP using the latest daily build. I’m using this port: /dev/cu.PL2303-00001004 Vendor: Yaesu Model: VX 170 I connect the cable with radio off, switch on with moni button held, put radio into Clone mode then press F key, hit OK button on CHIRP then press and hold the PTT until I get TX message on radio. All I get is “ Failed to communicate with radio: Failed to read header (0) Am I missing a driver or something? Some missed step? Thanks for the help. I’ve had good luck with Wouxun radios, working well. Roberto

2 1

[chirp_users] MacBook Air will not talk to UV-5RPlus
by Bob DeFranco 16 Apr '14

16 Apr '14

I have a MacBook Air running OS 10.9.2. I just installed CHIRP 0.4.0 and Python runtime and tried to program my UV-5RPlus. I get an error message saying that the radio did not respond. I checked the cable (Prolific chip) and found that the computer recognized it. I should note that I have used this same cable to program the same radio on a Windows 7 desktop PC, so I know the cable connects properly to the radio. Everything works, except I can't download data from my radio. Any thoughts or solutions? Bob DeFranco

7 17

Re: [chirp_users] Data on a Mechanical Filter used in a SB-34 HF Ham Transciever
by Bob Boehme 16 Apr '14

16 Apr '14

The spec is right in the model number... 455KHz frequency.. 2.1 KHz bandwidth.. The rig usually has two xtal oscillators which are set well down the upper or lower skirt of the filter depending on the sideband you desire.. very steep skirts on those mechanical filters.. -----Original Message----- From: chirp_users-bounces(a)intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Jeff Miller Sent: Tuesday, April 15, 2014 11:11 PM To: chirp_users(a)intrepid.danplanet.com Subject: [chirp_users] Data on a Mechanical Filter used in a SB-34 HF Ham Transciever I'm looking for any information, data and/or specifications on a mechanical filter used in a Sideband Engineers Model SB-34 Ham Transceiver. Model #: F455-FB21 1019 6330 Part #: 526-9448-00 Thanks, Jeff _______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users

1 0

[chirp_users] Data on a Mechanical Filter used in a SB-34 HF Ham Transciever
by Jeff Miller 16 Apr '14

16 Apr '14

I'm looking for any information, data and/or specifications on a mechanical filter used in a Sideband Engineers Model SB-34 Ham Transceiver. Model #: F455-FB21 1019 6330 Part #: 526-9448-00 Thanks, Jeff

2 1

[chirp_users] Chirp w/MacBook Air
by Steve Stombaugh 15 Apr '14

15 Apr '14

First post.... Bought the baofeng uv5r, and cable, from amazon. I've tried all the drivers I can find but don't see the MacBook recognizing the USB cable. Any ideas? Thanks. Sent from my iPad

5 10

[chirp_users] Message Archive, Dan Smith
by Canes Venatici 14 Apr '14

14 Apr '14

I see my test message arrived at the message archive but I'm not getting a copy. Is this actually being sent to others on the list or is the list server holding them for some reason? I'm not a new user I'm Milton formerly from Yahoo. So I really need to know if these two messages are propagating outwards to others. And where does the list server get my name from? Can that be changed back to Milton Milton

5 6

[chirp_users] Bounce test
by Milton Hywatt 14 Apr '14

14 Apr '14

Yahoo has been having issues with their POP servers and I guess a lot of list messages have been bouncing because I had to re-enable my account So if this keeps up, I thought it was fixed because I was getting email fine yesterday I will have to choose gmail to receive my list messages.

6 8

[chirp_users] new email
by Canes Venatici 14 Apr '14

14 Apr '14

I sure hop this works

1 0

Re: [chirp_users] Bounce test
by donparvin 13 Apr '14

13 Apr '14

My Hotmail are being bounced also so it might be system wide with the email servers. Sent from my Galaxy S®III -------- Original message -------- From: Jim Unroe <rock.unroe(a)gmail.com> Date:04/13/2014 12:19 (GMT-08:00) To: Milton Hywatt <mhywattt(a)yahoo.com>,Discussion of CHIRP <chirp_users(a)intrepid.danplanet.com> Subject: Re: [chirp_users] Bounce test On Sun, Apr 13, 2014 at 3:07 PM, Jim Unroe <rock.unroe(a)gmail.com> wrote: > On Sun, Apr 13, 2014 at 12:23 PM, Milton Hywatt <mhywattt(a)yahoo.com>wrote: > >> Yahoo has been having issues with their POP servers and >> I guess a lot of list messages have been bouncing because >> I had to re-enable my account So if this keeps up, I thought >> it was fixed because I was getting email fine yesterday I >> will have to choose gmail to receive my list messages. >> >> > Which may be related to why I had to move a few of your posts out of my > Gmail Spam folder and into my Inbox. > > Jim KC9HI > I guess not. I just had to move a post from Jens. So what I am experiencing is a Gmail issue. Hopefully it will become retrained soon. ;-) Jim KC9HI _______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users

1 0

[chirp_users] New Daily Build
by Build System 13 Apr '14

13 Apr '14

Greetings, A new daily build of CHIRP is available. This includes changes made directly to the tree yesterday, and may include additional features, bug fixes, and/or bugs. If you are interested in trying it, grab it from the following location: http://trac.chirp.danplanet.com/chirp_daily/daily-20140413 A list of the changes included in this build (since the last daily) follows: Changes for Build #271 [Dan Drogichen <chirp.cordless(a)xoxy.net>] [FT-60] Chirp should check parity on download - Fixes #1547 [Jim Unroe <rock.unroe(a)gmail.com>] [UV-B5] Update Frequency Ranges Update rf.valid_bands 130.000-175.000 MHz (expanded range) 220.000-269.000 MHz (added range) 400.000-520.000 MHz (unchanged) Expand the VHF Lower Limit setting range 128-270 Expand the VHF Upper Limit setting range 128-270 #1559

1 0

[chirp_users] Kenwood TH-K4 programming problem.
by Eduard Crombie 12 Apr '14

12 Apr '14

Hi, I have been using CHIRP since last year when I purchased a Baofeng UV5R. Since then I have been doing so successfully with other radios for friends and colleagues. With two Kenwood TH-K4 (UHF version of TH-K2), who are supported in the latest versions of CHIRP, I have this error window when trying to download from the ht: “could not open port COM2: [Error 5] access denied” after some 60 secs. (“access denied” is “Toegang geweigerd” in Dutch) Using the Kenwood program MCP-1A with same cable (on COM2 and original Prolific chip) I don’t have this problem, but the said software is not as flexible as CHIRP. Any ideas on how to tackle this problem ? 73 Eduard ON7CE

2 1

[chirp_users] Straightening out mixed terminology
by Pete Miller 08 Apr '14

08 Apr '14

Hi, Acknowledging up front that I'm a rookie, so give me all the guidance you think I need. Although I'm sorely tempted to curse the darkness, the reason for this mail is to try to light a candle, in case anyone else has some of the same questions. The challenge is differences in the terminology of repeater directories, CHIRP, and my new, first radio, a BaoFeng UV-5RE Plus. I've looked for answers in the CHIRP FAQ as well as some web searching. If you're not the right ones to deal with some or all of these questions, please share your suggestions about other sources. In advance, thanks. /kc1bkh -- Pete =-=-= Below are examples of a repeater directory table, a csv-formatted table for BaoFeng UV-5RE Plus, and the cloned CHIRP report for the UV-5RE Plus *The overall question:* How does the repeater directory terminology fit CHIRP's and the BaoFeng columns? ( This link was somewhat helpful, btw > http://kc5olo.org/downloads/repeater1.pdf . ) Repeater directory columns FREQOFSSTCITYCALLMODECODE IN OUTSTATUSCOUNTYIRLPECHOLINKS/COMMENTSLas =-= - Freq -- transmit frequency of repeater? yes, according to KC5OLO - OFS -- For example, standard offset for 2m is -600 kHz *What* gets entered *where* in the BaoFeng CSV and cloned columns? Maybe only the "-" or "+" or "split" gets entered? Then the offset is just calculated for each band? - Mode Same as BF-UV5 "Tone Mode", or maybe BF's "Mode" (which is usually FM for 2m band, right?) ? What is "Tone Mode"? - Code In and Code Out-- Here are four examples from the repeater directory 146.445+1MCTBridgeportWA1RJI77.0/ 156.777.0*Fairfield 224.680 (Rocky Hill, CT)2012/09/09146.475+1MCTNorwalk W1NLK100.0100.0Fairfield 2012/09/12146.625- CTFairfieldWB1CQO100.0Fairfield 146.655- CTStamfordW1EE100.0Fairfield 158564 WB1GRB-R2013/01/28 +1M is special offset? 146.445 : What does 77.0 / 156.7 for Code In mean? 146.445 : What does the red typestyle for Code Out mean? * means 'Gated PL' but I don't know what that means, yet. What are the units of the 77.0, 100.0, and 156.7 numbers? mHz? - IRLP - The Internet Radio Linking Project I'm not there yet - Echo - Refers to EchoLink® ? I'm not there yet =-= BaoFeng UV-5RE-Plus memory columns - cloned report downloaded from radio [image: Inline image 1] How do these terms map to the ones in the csv-format below? csv cloned Frequency.......Frequency Name...............Name Tone Mode.......? Tone................?Tone ToneSql...........? DTCS Code......Dtcs Code DTCS Rx Code ? DTCS Pol.........Dtcs Polarity CrossMode.......? Duplex..............Duplex Offset...............Offset Mode................?Mode Power...............? hi or lo, but I haven't found that detail, so far Skip.................Skip =-= BaoFeng UV-5RE-Plus memory columns - csv format Location |Name|Frequency|Duplex|Offset|Tone|rToneFreq|cToneFreq|DtcsCode| DtcsPolarity|Mode|TStep|Skip|CommentURCALLRPT1CALLRPT2CALL What are rToneFreq cToneFreq TStep Skip Why aren't the csv and cloned column headers and content the same? I do get that the column headers are supposed to guide the process of uploading to the radio, so the *order* of columns can be different. But why not make them the same, anyhow? May be a BaoFeng problem: When I try to manually enter info directly into the clone report, I can enter Name and Frequency, but clicking on other columns just makes the entire row (such as, the row for memory location 22) go away; seems to erase the row. I haven't figured out how to recover it, but since I haven't uploaded anything, I can of course download a new image. Suggestions about how to make direct entry into the downloaded, "cloned" report? =-= Thanks. I've done my best to provide enough context, but if you want any more info, just ask.

5 6

Re: [chirp_users] Cannot Upload to Yausu VX-6
by Richard Martinelli 08 Apr '14

08 Apr '14

I'm having the same problem trying to upload to my Yaesu VX-7R as that which is described in Issue 1433. I was able to download the image, made some changes and now cannot upload it back. The only thing different from what was identified in Issue 1433 is I'm running Mountain Lion 10.8.5 and the new Apple FTDI drive is not utilized. I'm running the FTDI 2.2.18 driver downloaded from their site. Is there any update regarding 10.8.5 and the FTDI driver? I have not been able to locate any issues regarding FTDI and 10.8.5. Any suggestions would be greatly appreciated. I have tried various changes to the Info.plist file, as suggested by FTDI site documents, but nothing seems to make any deference. So, after several weeks of frustration, I'm looking for any suggestions/help. The cable I'm using was purchased from Valley Enterprises and my system does "see" it and so does CHIRP. It sure does sound like it's a driver issue, but I just don't know were to go from here. I've include the System Panic Report and the CHIRP debug.log, which I ran just before I Forced Quit the program, which causes the system panic. That is the only way I can get CHIRP to stop trying to upload. I would send the after reboot debug.log, but CHIRP automatically restarts and clears the log. Sorry for the long email, I guess it's a "newbee" thing, Rich PANIC REPORT: Interval Since Last Panic Report: 586137 sec Panics Since Last Report: 29 Anonymous UUID: 299230DF-0877-496F-0E01-31DC8FF59673 Fri Apr 4 21:24:58 2014 panic(cpu 2 caller 0xffffff80280b8945): Kernel trap at 0xffffff7fa9d1ef59, type 13=general protection, registers: CR0: 0x000000008001003b, CR2: 0x0000000104479830, CR3: 0x000000002a425000, CR4: 0x00000000001606e0 RAX: 0xffffff80344a6300, RBX: 0xffffff8041cd9000, RCX: 0xffffff80286f4820, RDX: 0x0000000000000007 RSP: 0xffffff802f61bc80, RBP: 0xffffff802f61bca0, RSI: 0xffffff803332fc00, RDI: 0xffffff803dd50900 R8: 0x0000000000000000, R9: 0x0000000000000000, R10: 0xffffff803367b9c0, R11: 0xffffff802f61bda4 R12: 0x0000000000000007, R13: 0xffffff803332fc00, R14: 0xffffff8041cd9000, R15: 0xffffff803332fc00 RFL: 0x0000000000010286, RIP: 0xffffff7fa9d1ef59, CS: 0x0000000000000008, SS: 0x0000000000000000 Fault CR2: 0x0000000104479830, Error code: 0x0000000000000000, Fault CPU: 0x2 Backtrace (CPU 2), Frame : Return Address 0xffffff802f61b920 : 0xffffff802801d636 0xffffff802f61b990 : 0xffffff80280b8945 0xffffff802f61bb60 : 0xffffff80280cebfd 0xffffff802f61bb80 : 0xffffff7fa9d1ef59 0xffffff802f61bca0 : 0xffffff8028438889 0xffffff802f61bcf0 : 0xffffff802844fdd1 0xffffff802f61bd30 : 0xffffff8028438d4b 0xffffff802f61bd70 : 0xffffff80284380ca 0xffffff802f61bdd0 : 0xffffff8028437d77 0xffffff802f61be10 : 0xffffff8028437b27 0xffffff802f61be80 : 0xffffff8028438edc 0xffffff802f61be90 : 0xffffff7fa8825703 0xffffff802f61bec0 : 0xffffff7fa8998a0a 0xffffff802f61bf00 : 0xffffff7fa8998fb4 0xffffff802f61bf40 : 0xffffff7fa8997bac 0xffffff802f61bf60 : 0xffffff802803e26e 0xffffff802f61bfb0 : 0xffffff80280b3257 Kernel Extensions in backtrace: com.apple.iokit.IOUSBFamily(635.4)[E67F44F7-A4BD-3CD1-A01B-B37D783CE613]@0xffffff7fa8811000->0xffffff7fa886efff dependency: com.apple.iokit.IOPCIFamily(2.8)[2FAEA49C-EA4C-39C6-9203-FC022277A43C]@0xffffff7fa8675000 com.apple.driver.AppleUSBHub(635.4)[52517FC7-F1EF-3E05-99DC-7553722B8EFF]@0xffffff7fa898e000->0xffffff7fa89a2fff dependency: com.apple.iokit.IOUSBFamily(635.4.0)[E67F44F7-A4BD-3CD1-A01B-B37D783CE613]@0xffffff7fa8811000 com.FTDI.driver.FTDIUSBSerialDriver(2.2.18)[638ECCC3-375D-CD1A-C2EC-0DC14740FC9C]@0xffffff7fa9d1d000->0xffffff7fa9d24fff dependency: com.apple.iokit.IOUSBFamily(635.4.0)[E67F44F7-A4BD-3CD1-A01B-B37D783CE613]@0xffffff7fa8811000 dependency: com.apple.iokit.IOSerialFamily(10.0.6)[7191512A-FD43-339A-BE50-857BFD87B27C]@0xffffff7fa8ad1000 BSD process name corresponding to current thread: kernel_task Mac OS version: 12F45 Kernel version: Darwin Kernel Version 12.5.0: Sun Sep 29 13:33:47 PDT 2013; root:xnu-2050.48.12~1/RELEASE_X86_64 Kernel UUID: EA38B02E-2B88-309F-BA68-1DE29F605DD8 Kernel slide: 0x0000000027e00000 Kernel text base: 0xffffff8028000000 System model name: MacBookPro9,2 (Mac-6F01561E16C75D06) System uptime in nanoseconds: 5381982690136 last loaded kext at 527967674926: com.FTDI.driver.FTDIUSBSerialDriver 2.2.18 (addr 0xffffff7fa9d1d000, size 57344) last unloaded kext at 589027282033: com.apple.driver.AppleUSBCDC 4.1.23 (addr 0xffffff7fa9d1a000, size 12288) loaded kexts: com.FTDI.driver.FTDIUSBSerialDriver 2.2.18 com.squirrels.airparrot.framebuffer 3 com.apple.iokit.IOBluetoothSerialManager 4.1.7f2 com.apple.driver.AudioAUUC 1.60 com.apple.driver.AGPM 100.13.12 com.apple.driver.X86PlatformShim 1.0.0 com.apple.driver.AppleMikeyHIDDriver 124 com.apple.filesystems.autofs 3.0 com.apple.driver.AppleSMCPDRC 1.0.0 com.apple.driver.AppleHDA 2.4.7fc4 com.apple.driver.AppleIntelHD4000Graphics 8.1.6 com.apple.driver.AppleMikeyDriver 2.4.7fc4 com.apple.driver.AppleSMBusPCI 1.0.11d1 com.apple.driver.AppleLPC 1.6.3 com.apple.driver.AppleUpstreamUserClient 3.5.12 com.apple.iokit.IOUserEthernet 1.0.0d1 com.apple.Dont_Steal_Mac_OS_X 7.0.0 com.apple.driver.ApplePolicyControl 3.4.5 com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport 4.1.7f4 com.apple.driver.AppleSMCLMU 2.0.3d0 com.apple.driver.AppleIntelFramebufferCapri 8.1.6 com.apple.driver.AppleBacklight 170.3.5 com.apple.driver.AppleMCCSControl 1.1.11 com.apple.driver.SMCMotionSensor 3.0.3d1 com.apple.driver.AppleUSBTCButtons 237.1 com.apple.driver.AppleUSBTCKeyboard 237.1 com.apple.driver.AppleIRController 320.15 com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1 com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1 com.apple.BootCache 34 com.apple.iokit.SCSITaskUserClient 3.5.6 com.apple.driver.XsanFilter 404 com.apple.iokit.IOAHCIBlockStorage 2.3.5 com.apple.driver.AppleFWOHCI 4.9.9 com.apple.driver.AirPort.Brcm4331 615.20.17 com.apple.driver.AppleSDXC 1.4.3 com.apple.iokit.AppleBCM5701Ethernet 3.6.2b4 com.apple.driver.AppleUSBHub 635.4.0 com.apple.driver.AppleAHCIPort 2.6.6 com.apple.driver.AppleUSBEHCI 621.4.6 com.apple.driver.AppleUSBXHCI 635.4.0 com.apple.driver.AppleSmartBatteryManager 161.0.0 com.apple.driver.AppleHPET 1.8 com.apple.driver.AppleRTC 1.5 com.apple.driver.AppleACPIButtons 1.8 com.apple.driver.AppleSMBIOS 1.9 com.apple.driver.AppleACPIEC 1.8 com.apple.driver.AppleAPIC 1.7 com.apple.driver.AppleIntelCPUPowerManagementClient 214.0.0 com.apple.nke.applicationfirewall 4.0.39 com.apple.security.quarantine 2.1 com.apple.driver.AppleIntelCPUPowerManagement 214.0.0 com.apple.iokit.IOSerialFamily 10.0.6 com.apple.kext.triggers 1.0 com.apple.driver.DspFuncLib 2.4.7fc4 com.apple.iokit.IOAudioFamily 1.9.2fc7 com.apple.kext.OSvKernDSPLib 1.12 com.apple.iokit.IOAcceleratorFamily 74.15 com.apple.driver.X86PlatformPlugin 1.0.0 com.apple.driver.IOPlatformPluginFamily 5.4.1d13 com.apple.iokit.IOSurface 86.0.4 com.apple.iokit.IOBluetoothFamily 4.1.7f2 com.apple.iokit.IOBluetoothHostControllerUSBTransport 4.1.7f2 com.apple.iokit.IOFireWireIP 2.2.5 com.apple.driver.AppleHDAController 2.4.7fc4 com.apple.iokit.IOHDAFamily 2.4.7fc4 com.apple.driver.AppleSMBusController 1.0.11d1 com.apple.driver.AppleGraphicsControl 3.4.5 com.apple.driver.AppleBacklightExpert 1.0.4 com.apple.iokit.IONDRVSupport 2.3.7 com.apple.iokit.IOGraphicsFamily 2.3.7 com.apple.driver.AppleSMC 3.1.5d4 com.apple.driver.AppleUSBMultitouch 237.3 com.apple.driver.AppleThunderboltDPInAdapter 2.5.0 com.apple.driver.AppleThunderboltDPAdapterFamily 2.5.0 com.apple.driver.AppleThunderboltPCIDownAdapter 1.3.2 com.apple.iokit.IOUSBHIDDriver 623.4.0 com.apple.driver.AppleUSBMergeNub 621.4.6 com.apple.driver.AppleUSBComposite 621.4.0 com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.5.6 com.apple.iokit.IOBDStorageFamily 1.7 com.apple.iokit.IODVDStorageFamily 1.7.1 com.apple.iokit.IOCDStorageFamily 1.7.1 com.apple.iokit.IOAHCISerialATAPI 2.5.5 com.apple.iokit.IOSCSIArchitectureModelFamily 3.5.6 com.apple.driver.AppleThunderboltNHI 1.9.2 com.apple.iokit.IOThunderboltFamily 2.7.7 com.apple.iokit.IOFireWireFamily 4.5.5 com.apple.iokit.IO80211Family 530.5 com.apple.iokit.IOEthernetAVBController 1.0.2b1 com.apple.iokit.IONetworkingFamily 3.0 com.apple.iokit.IOAHCIFamily 2.5.1 com.apple.iokit.IOUSBUserClient 630.4.4 com.apple.iokit.IOUSBFamily 635.4.0 com.apple.driver.AppleEFINVRAM 2.0 com.apple.driver.AppleEFIRuntime 2.0 com.apple.iokit.IOHIDFamily 1.8.1 com.apple.iokit.IOSMBusFamily 1.1 com.apple.security.sandbox 220.3 com.apple.kext.AppleMatch 1.0.0d1 com.apple.security.TMSafetyNet 7 com.apple.driver.DiskImages 345 com.apple.iokit.IOStorageFamily 1.8 com.apple.driver.AppleKeyStore 28.21 com.apple.driver.AppleACPIPlatform 1.8 com.apple.iokit.IOPCIFamily 2.8 com.apple.iokit.IOACPIFamily 1.4 com.apple.kec.corecrypto 1.0 Model: MacBookPro9,2, BootROM MBP91.00D3.B08, 2 processors, Intel Core i5, 2.5 GHz, 4 GB, SMC 2.2f44 Graphics: Intel HD Graphics 4000, Intel HD Graphics 4000, Built-In, 512 MB Memory Module: BANK 0/DIMM0, 2 GB, DDR3, 1600 MHz, 0x802C, 0x384A54463235363634485A2D3147364D3120 Memory Module: BANK 1/DIMM0, 2 GB, DDR3, 1600 MHz, 0x802C, 0x384A54463235363634485A2D3147364D3120 AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0xF5), Broadcom BCM43xx 1.0 (5.106.98.100.17) Bluetooth: Version 4.1.7f2 12718, 3 service, 13 devices, 3 incoming serial ports Network Service: AirPort, AirPort, en1 Serial ATA Device: APPLE HDD ST500LM012, 500.11 GB Serial ATA Device: HL-DT-ST DVDRW GS31N USB Device: FT232R USB UART, 0x0403 (Future Technology Devices International Limited), 0x6001, 0x14100000 / 1 USB Device: hub_device, 0x8087 (Intel Corporation), 0x0024, 0x1a100000 / 2 USB Device: FaceTime HD Camera (Built-in), apple_vendor_id, 0x8509, 0x1a110000 / 3 USB Device: hub_device, 0x8087 (Intel Corporation), 0x0024, 0x1d100000 / 2 USB Device: hub_device, 0x0424 (SMSC), 0x2513, 0x1d180000 / 3 USB Device: BRCM20702 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x1d181000 / 6 USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x821d, 0x1d181300 / 7 USB Device: IR Receiver, apple_vendor_id, 0x8242, 0x1d182000 / 5 USB Device: Apple Internal Keyboard / Trackpad, apple_vendor_id, 0x0252, 0x1d183000 / 4 DEBUG.LOG: CHIRP 0.4.0 on Darwin Rich-Computer-2.local 12.5.0 Darwin Kernel Version 12.5.0: Sun Sep 29 13:33:47 PDT 2013; root:xnu-2050.48.12~1/RELEASE_X86_64 x86_64 (Python 2.7.2) Registered Alinco_DR03T = DR03Radio Registered Alinco_DR06T = DR06Radio Registered Alinco_DR135T = DR135Radio Registered Alinco_DR235T = DR235Radio Registered Alinco_DR435T = DR435Radio Registered Alinco_DJ596 = DJ596Radio Registered Jetstream_JT220M = JT220MRadio Registered Alinco_DJ175 = DJ175Radio Registered AnyTone_5888UV = AnyTone5888UVRadio Registered Intek_HR-2040 = IntekHR2040Radio Registered Polmar_DB-50M = PolmarDB50MRadio Registered Powerwerx_DB-750X = PowerwerxDB750XRadio Registered Baofeng_UV-3R = UV3RRadio Registered Baofeng_UV-5R = BaofengUV5R Registered Baofeng_F-11 = BaofengF11Radio Registered Baofeng_UV-82 = BaofengUV82Radio Registered Baofeng_UV-6 = BaofengUV6Radio Registered Baojie_BJ-UV55 = BaojieBJUV55Radio Registered Kenwood_TH-D7 = THD7Radio Registered Kenwood_TH-D7G = THD7GRadio Registered Kenwood_TM-D700 = TMD700Radio Registered Kenwood_TM-V7 = TMV7Radio Registered Kenwood_TM-G707 = TMG707Radio Registered Kenwood_TH-G71 = THG71Radio Registered Kenwood_TH-F6 = THF6ARadio Registered Kenwood_TH-F7 = THF7ERadio Registered Kenwood_TM-D710 = TMD710Radio Registered Kenwood_TH-D72_live_mode = THD72Radio Registered Kenwood_TM-V71 = TMV71Radio Registered Kenwood_TH-K2 = THK2Radio Registered Kenwood_TM-271 = TM271Radio Registered Kenwood_TM-281 = TM281Radio Registered Kenwood_TM-471 = TM471Radio Registered Icom_7200 = Icom7200Radio Registered Icom_7000 = Icom7000Radio Registered Icom_746 = Icom746Radio Registered Yaesu_FT-1802M = FT1802Radio Registered Yaesu_FT-2800M = FT2800Radio Registered Yaesu_FT-60 = FT60Radio Registered Yaesu_FT-7800_7900 = FT7800Radio Registered Yaesu_FT-8800 = FT8800Radio Registered Yaesu_FT-8900 = FT8900Radio Registered Yaesu_FT-817 = FT817Radio Registered Yaesu_FT-817ND = FT817NDRadio Registered Yaesu_FT-817ND_US = FT817NDUSRadio Registered Yaesu_FT-857_897 = FT857Radio Registered Yaesu_FT-857_897_US = FT857USRadio Registered Yaesu_FT-90 = FT90Radio Registered Yaesu_FTM-350 = FTM350Radio Registered Generic_CSV = CSVRadio Registered Commander_KG-UV = CommanderCSVRadio Registered RT_Systems_CSV = RTCSVRadio Registered ARRL_Travel_Plus = TpeRadio Registered Generic_XML = XMLRadio Registered Baofeng_BF-888 = H777Radio Registered Icom_IC-208H = IC208Radio Registered Icom_IC-2100H = IC2100Radio Registered Icom_IC-2200H = IC2200Radio Registered Icom_IC-2720H = IC2720Radio Registered Icom_IC-2820H = IC2820Radio Registered Icom_IC-91_92AD = IC9xRadio Registered Icom_IC-91_92AD_ICF_File = IC9xICFRadio Registered Icom_IC-Q7A = ICQ7Radio Registered Icom_IC-T70 = ICT70Radio Registered Icom_IC-T7H = ICT7HRadio Registered Icom_IC-T8A = ICT8ARadio Registered Icom_IC-W32A = ICW32ARadio Registered Icom_IC-V82_U82 = ICx8xRadio Registered Icom_ID-31A = ID31Radio Registered Icom_ID-51A = ID51Radio Registered Icom_ID-800H_v2 = ID800v2Radio Registered Icom_ID-880H = ID880Radio Registered Icom_ID-80H = ID80Radio Registered Kenwood_HMK = HMKRadio Registered Kenwood_ITM = ITMRadio Registered Puxing_PX-777 = Puxing777Radio Registered Puxing_PX-2R = Puxing2RRadio Registered TYT_TH-UV3R = TYTUV3RRadio Registered TYT_TH-UVF8D = TYTUVF8DRadio Registered Kenwood_TH-D72_clone_mode = THD72Radio Registered TYT_TH-UVF1 = TYTTHUVF1Radio Registered Kenwood_TK-7102 = KenwoodTK7102Radio Registered Kenwood_TK-8102 = KenwoodTK8102Radio Registered Kenwood_TK-7108 = KenwoodTK7108Radio Registered Kenwood_TK-8108 = KenwoodTK8108Radio Registered Baofeng_UV-B5 = BaofengUVB5 Registered Yaesu_VX-2 = VX2Radio Registered Yaesu_VX-3 = VX3Radio Registered Yaesu_VX-5 = VX5Radio Registered Yaesu_VX-6 = VX6Radio Registered Yaesu_VX-7 = VX7Radio Registered Yaesu_VX-8_R = VX8Radio Registered Yaesu_VX-8_DR = VX8DRadio Registered Yaesu_VX-8_GE = VX8GERadio Registered Vertex_Standard_VXA-700 = VXA700Radio Registered Wouxun_KG-UVD1P = KGUVD1PRadio Registered Wouxun_KG-UV6 = KGUV6DRadio Registered Wouxun_KG-816 = KG816Radio Registered Wouxun_KG-818 = KG818Radio Icon /usr/share/pixmaps/chirp.png not found Initialized MacOS support /Applications/chirp-0.4.0.app/Contents/MacOS/../Resources/chirp/chirpw:146: PangoWarning: error opening config file '../Resources/etc/pango/pangorc': No such file or directory a.show() Bandplan North American Band Plan has duplicates [1800000-2000000 160 Meter Band simplex , 1800000-2000000 160 Meter Band simplex mode: CW ] Bandplan North American Band Plan has duplicates [1800000-1810000 Digimodes simplex , 1800000-1810000 Digital Modes simplex ] Bandplan North American Band Plan has duplicates [1999000-2000000 Beacons simplex mode: CW , 1999000-2000000 Beacons simplex ] Bandplan North American Band Plan has duplicates [3500000-4000000 80 Meter Band simplex , 3500000-4000000 80 Meter Band simplex ] Bandplan North American Band Plan has duplicates [7000000-7300000 40 Meter Band simplex , 7000000-7300000 40 Meter Band simplex ] Bandplan North American Band Plan has duplicates [10100000-10150000 30 Meter Band simplex , 10100000-10150000 30 Meter Band simplex ] Bandplan North American Band Plan has duplicates [10130000-10140000 All narrow band digimodes simplex , 10130000-10140000 RTTY simplex mode: RTTY ] Bandplan North American Band Plan has duplicates [10140000-10150000 All modes, digimodes, no phone simplex , 10140000-10150000 Packet simplex ] Bandplan North American Band Plan has duplicates [14000000-14350000 20 Meter Band simplex , 14000000-14350000 20 Meter Band simplex ] Bandplan North American Band Plan has duplicates [18068000-18168000 17 Meter Band simplex , 18068000-18168000 17 Meter Band simplex ] Bandplan North American Band Plan has duplicates [21000000-21450000 15 Meter Band simplex , 21000000-21450000 15 Meter Band simplex ] Bandplan North American Band Plan has duplicates [24890000-24990000 12 Meter Band simplex , 24890000-24990000 12 Meter Band simplex ] Bandplan North American Band Plan has duplicates [28000000-28070000 CW simplex mode: CW , 28000000-28070000 CW simplex mode: CW ] Bandplan North American Band Plan has duplicates [28150000-28190000 All narrow band modes, digimodes simplex , 28150000-28190000 CW simplex mode: CW ] Bandplan North American Band Plan has duplicates [29000000-29200000 All modes, AM preferred simplex mode: AM , 29000000-29200000 AM simplex mode: AM ] Bandplan North American Band Plan has duplicates [29300000-29510000 Satellite downlink simplex , 29300000-29510000 Satellite Downlinks simplex ] Bandplan North American Band Plan has duplicates [1800000-2000000 160 Meter Band simplex , 1800000-2000000 160 Meter Band simplex mode: CW ] Bandplan North American Band Plan has duplicates [1800000-1810000 Digimodes simplex , 1800000-1810000 Digital Modes simplex ] Bandplan North American Band Plan has duplicates [1999000-2000000 Beacons simplex mode: CW , 1999000-2000000 Beacons simplex ] Bandplan North American Band Plan has duplicates [3500000-4000000 80 Meter Band simplex , 3500000-4000000 80 Meter Band simplex ] Bandplan North American Band Plan has duplicates [7000000-7300000 40 Meter Band simplex , 7000000-7300000 40 Meter Band simplex ] Bandplan North American Band Plan has duplicates [10100000-10150000 30 Meter Band simplex , 10100000-10150000 30 Meter Band simplex ] Bandplan North American Band Plan has duplicates [10130000-10140000 All narrow band digimodes simplex , 10130000-10140000 RTTY simplex mode: RTTY ] Bandplan North American Band Plan has duplicates [10140000-10150000 All modes, digimodes, no phone simplex , 10140000-10150000 Packet simplex ] Bandplan North American Band Plan has duplicates [14000000-14350000 20 Meter Band simplex , 14000000-14350000 20 Meter Band simplex ] Bandplan North American Band Plan has duplicates [18068000-18168000 17 Meter Band simplex , 18068000-18168000 17 Meter Band simplex ] Bandplan North American Band Plan has duplicates [21000000-21450000 15 Meter Band simplex , 21000000-21450000 15 Meter Band simplex ] Bandplan North American Band Plan has duplicates [24890000-24990000 12 Meter Band simplex , 24890000-24990000 12 Meter Band simplex ] Bandplan North American Band Plan has duplicates [28000000-28070000 CW simplex mode: CW , 28000000-28070000 CW simplex mode: CW ] Bandplan North American Band Plan has duplicates [28150000-28190000 All narrow band modes, digimodes simplex , 28150000-28190000 CW simplex mode: CW ] Bandplan North American Band Plan has duplicates [29000000-29200000 All modes, AM preferred simplex mode: AM , 29000000-29200000 AM simplex mode: AM ] Bandplan North American Band Plan has duplicates [29300000-29510000 Satellite downlink simplex , 29300000-29510000 Satellite Downlinks simplex ] DTCS Code supported: True DTCS Rx Code supported: False DTCS Pol supported: False Mode supported: True Offset supported: True Name supported: True Tune Step supported: True Name supported: True ToneSql supported: False Cross Mode supported: True Comment supported: False DTCS Code supported: True DTCS Rx Code supported: False DTCS Pol supported: False Mode supported: True Offset supported: True Name supported: True Tune Step supported: True Name supported: True ToneSql supported: False Cross Mode supported: True Comment supported: False Opening port after pre_upload prompt. Clone thread started

4 4

[chirp_users] CHIRP UNBricked my Wouxun
by John Kellas 07 Apr '14

07 Apr '14

A few years ago, I was programming some Wouxun UVD1P radios using either the factory software, or UVD Commander. Not paying attention, I inadvertently connected my VHF only Wouxun KG-816 and programmed it with the wrong software that contained UHF frequencies. When it rebooted, it only spoke chinese, and would only display 400mHz. I treid to recover it using factory reset, the out of band hack, and the OEM software, to no avail. So I put it in a drawer to be used for parts. Today I was programming another KG-816, so for the heck of it, I connected the bricked unit to see what would happen if I tried CHIRP. When it rebooted, it was back to speaking English, with all the VHF channels restored. I recall there seems to be a problem with US Versions of the UVD-1P. As that problem has not been seen in International Versions, I've always suspected it's due to the out of band hack. Anyway, whether CHIRP can help with that or not, it certainly seemed to achieve the ability to unbrick my 816, so maybe it can help with other bricked models as well. Regards, John

1 0

[chirp_users] New Daily Build
by Build System 07 Apr '14

07 Apr '14

Greetings, A new daily build of CHIRP is available. This includes changes made directly to the tree yesterday, and may include additional features, bug fixes, and/or bugs. If you are interested in trying it, grab it from the following location: http://trac.chirp.danplanet.com/chirp_daily/daily-20140407 A list of the changes included in this build (since the last daily) follows: Changes for Build #270 [Marco Filippi <iz3gme.marco(a)gmail.com>] [NC-630A] Reverse skip logic completes #1525 [Jim Unroe <rock.unroe(a)gmail.com>] [NC-630A] Add Support for KYD NC-630A KYD NC630A UHF Handheld Add Spreadsheet Memory Editor support Add Basic Settings support #1525 [Jens Jensen <kd4tjx(a)yahoo.com>] [vx170] initial vx170 support #1183 [Jens Jensen <kd4tjx(a)yahoo.com>] [ft7800] updating ft7800 class to support subclassing #1183 prequisite changes to support subclassing for vx170 move power levels to class member use _block_size class member for chunk size in transfers [Marco Filippi <iz3gme.marco(a)gmail.com>] [kt-980HP] Add new UV-5R clone implement #1517 [Dan Smith <dsmith(a)danplanet.com>] Add updated French translation Related to #1533

1 0

[chirp_users] CHIRP for Android?
by Rich Barstow 06 Apr '14

06 Apr '14

Forgive me for asking, but I searched the last few months of mailing list archives, both on the user and the dev side, without finding a roadmap or references to an Android version. Are there any plans? If not, what's the best way to contact the developers to discuss? If yes, how can I offer assistance? (testing or coding)

5 7

[chirp_users] Support for Memory Banks
by Mike Shelby 05 Apr '14

05 Apr '14

I'm probably missing something rather basic. In CHIRP I do not see any support for memory banks. I have an IC-7000 that has 5 banks of 99 channels each. In my IC-91AD there are 26 bands that can manage 800 memory channels. I have 4 more radios that support the concept of Memory Banks. There are many more radios available to hams that have this same basic concept for managing and grouping memory into logical blocks, known as Memory Banks. What am I missing, how do you configure CHIRP to handle Memory Banks? Mike - W7RIS

4 3

Re: [chirp_users] chirp_users Digest, Vol 64, Issue 4
by jimbo 04 Apr '14

04 Apr '14

can any one tell me why ic-91ad radio and chirp well not work right on windows 7 i have use chirp many times on other radios but for some reason i cant get the this to work On 4/4/2014 12:00 PM, chirp_users-request(a)intrepid.danplanet.com wrote: > Send chirp_users mailing list submissions to > chirp_users(a)intrepid.danplanet.com > > To subscribe or unsubscribe via the World Wide Web, visit > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > or, via email, send a message with subject or body 'help' to > chirp_users-request(a)intrepid.danplanet.com > > You can reach the person managing the list at > chirp_users-owner(a)intrepid.danplanet.com > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of chirp_users digest..." > > > Today's Topics: > > 1. New Daily Build (Build System) > 2. Re: New Daily Build (Anthony Danton) > 3. icom ic7100 (Anthony Danton) > 4. Re: icom ic7100 (Milton Hywatt) > 5. How to make bug report? (Tom ND5Y) > 6. Re: How to make bug report? (Jens J.) > > > ---------------------------------------------------------------------- > > Message: 1 > Date: Fri, 4 Apr 2014 00:07:36 -0700 (PDT) > From: Build System <donotreply(a)danplanet.com> > Subject: [chirp_users] New Daily Build > To: chirp_users(a)intrepid.danplanet.com > Message-ID: > <789994228.187.1396595256172.JavaMail.jenkins(a)eagle.danplanet.com> > Content-Type: text/plain; charset="utf-8" > > Greetings, > > A new daily build of CHIRP is available. This includes changes made > directly to the tree yesterday, and may include additional features, > bug fixes, and/or bugs. If you are interested in trying it, grab it > from the following location: > > http://trac.chirp.danplanet.com/chirp_daily/daily-20140404 > > > A list of the changes included in this build (since the last daily) > follows: > > Changes for Build #269 > [Dan Smith <dsmith(a)danplanet.com>] Add French translation from Matthieu > Related to #1429 > > [Dan Smith <dsmith(a)danplanet.com>] Added tag release_0_4_0 for changeset e91f09ca03d0 > > > > ------------------------------ > > Message: 2 > Date: Fri, 4 Apr 2014 08:19:05 +0100 > From: Anthony Danton <ardnw(a)aol.com> > Subject: Re: [chirp_users] New Daily Build > To: Discussion of CHIRP <chirp_users(a)intrepid.danplanet.com> > Message-ID: <2200B602-E142-40E9-9B7E-630119C245BE(a)aol.com> > Content-Type: text/plain; charset=us-ascii > > Do you know if the software will work with an Icom Ic7100 ?? > > > tony > > > > > On 4 Apr 2014, at 08:07, Build System wrote: > >> Greetings, >> >> A new daily build of CHIRP is available. This includes changes made >> directly to the tree yesterday, and may include additional features, >> bug fixes, and/or bugs. If you are interested in trying it, grab it >> from the following location: >> >> http://trac.chirp.danplanet.com/chirp_daily/daily-20140404 >> >> >> A list of the changes included in this build (since the last daily) >> follows: >> >> Changes for Build #269 >> [Dan Smith <dsmith(a)danplanet.com>] Add French translation from Matthieu >> Related to #1429 >> >> [Dan Smith <dsmith(a)danplanet.com>] Added tag release_0_4_0 for changeset e91f09ca03d0 >> >> >> _______________________________________________ >> chirp_users mailing list >> chirp_users(a)intrepid.danplanet.com >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users > > > ------------------------------ > > Message: 3 > Date: Fri, 4 Apr 2014 08:39:29 +0100 > From: Anthony Danton <ardnw(a)aol.com> > Subject: [chirp_users] icom ic7100 > To: Discussion of CHIRP <chirp_users(a)intrepid.danplanet.com> > Message-ID: <564C6A85-311E-4B4B-BA09-8418AED7C4FA(a)aol.com> > Content-Type: text/plain; charset=us-ascii > > Do you know if the software will work with the Icom Ic 7100 ?? > > tony > > > ------------------------------ > > Message: 4 > Date: Fri, 4 Apr 2014 09:46:23 -0700 (PDT) > From: Milton Hywatt <mhywattt(a)yahoo.com> > Subject: Re: [chirp_users] icom ic7100 > To: Discussion of CHIRP <chirp_users(a)intrepid.danplanet.com> > Message-ID: > <1396629983.55024.YahooMailNeo(a)web162601.mail.bf1.yahoo.com> > Content-Type: text/plain; charset="us-ascii" > > If it does it will be listen in the program. Also > read this page: > > http://chirp.danplanet.com/projects/chirp/wiki/Supported_Radios > > > > > ________________________________ > From: Anthony Danton <ardnw(a)aol.com> > To: Discussion of CHIRP <chirp_users(a)intrepid.danplanet.com> > Sent: Friday, April 4, 2014 3:39 AM > Subject: [chirp_users] icom ic7100 > > > Do you know if the software will work with the Icom Ic 7100 ?? > > tony > _______________________________________________ > chirp_users mailing list > chirp_users(a)intrepid.danplanet.com > http://intrepid.danplanet.com/mailman/listinfo/chirp_users >

2 1

[chirp_users] How to make bug report?
by Tom ND5Y 04 Apr '14

04 Apr '14

What is the proper way to file a bug report? I tried downloading from a Yaesu FT-7800R and CHIRP can't handle some of the tone encode and decode modes correctly. Tom ND5Y

2 1

[chirp_users] icom ic7100
by Anthony Danton 04 Apr '14

04 Apr '14

Do you know if the software will work with the Icom Ic 7100 ?? tony

2 1

[chirp_users] New Daily Build
by Build System 04 Apr '14

04 Apr '14

Greetings, A new daily build of CHIRP is available. This includes changes made directly to the tree yesterday, and may include additional features, bug fixes, and/or bugs. If you are interested in trying it, grab it from the following location: http://trac.chirp.danplanet.com/chirp_daily/daily-20140404 A list of the changes included in this build (since the last daily) follows: Changes for Build #269 [Dan Smith <dsmith(a)danplanet.com>] Add French translation from Matthieu Related to #1429 [Dan Smith <dsmith(a)danplanet.com>] Added tag release_0_4_0 for changeset e91f09ca03d0

2 1

[chirp_users] programming help
by Skip 03 Apr '14

03 Apr '14

Chirp Users, All I want to do is program my little radio (UV-5R). I installed the Prolific software a few weeks ago and downloaded CHIRP and began programming. I have read over and over information in the Miklor web site. I was able to put a couple of frequencies in CHIRP. I downloaded them to the radio but the radio didn’t work as I probably had the Tone or Offset not right. I spent a lot hours trying to learn how and gave up. I then went to the manual programming directions and I can’t program fast enough as the radio times out. (I have a neurology problem that causes shaking, especially when frustrated.) Next I get an email that announces a CHIRP update to 4.0. I install it and try to program again. Now Prolific won’t install. I have a Windows 7 64 bit computer. I live in a rural area with no Elmer’s. I guess I’m having problems due to my age or stupidity. I am willing to call someone who may walk me through the whole process. As you can tell I’m behind the curve on computers as well.

6 8

[chirp_users] Cannot program Simplex from Imported CSV
by John Kellas 02 Apr '14

02 Apr '14

I have a .img file created by reading an Anytone 588UV. I have another .csv file I want to use to populate the 5888 file. In my .csv file, all the channels are 'split' in the Duplex Column, and the absolute frequency shows in the offset column. If I paste the data from the .csv file into my CHIRP .img file: 1. my only choices become '-' or '+' in the Duplex Col of the .img file for the 5888, whereas they were 'split' in the .csv file 2. and in the Offset col the simplex channels are blank in the Offset column, and the repeater channels have been transposed to an offset value rather than an ablsolute value. Is this because CHIRP will not allow 'split' as an option for duplex because of the radio model number for some reason? Regards, John

8 19