- Users - lists.chirpmyradio.com

[chirp_users] Unsupported Firmware
by Greg Hicks 07 Jan '15

07 Jan '15

Good Morning to All from new guy.... Greg here in Indianapolis, and brand new to the group & using CHIRP. Just received a BaoFeng BF-F8HP yesterday and have been playing with. I was amble to download from radio, but not upload. When I try to upload a new 'img' file, I get the following error message: Unsupported firmware version: N5R3401F8HP-1 Not sure how to look for this, nor where to find. Thanks, in advance for any help..... Greg <===><===><===><===><===> Greg Hicks, K9TLA Hancock County CERT Program Manager 317-501-5389 (cell) <===><===><===><===><===>

2 1

[chirp_users] Support for Icom ID-51E Special Edition
by Håken Hveem 06 Jan '15

06 Jan '15

Hello, is there any support for the Support for Icom ID-51E Special Edition at the moment, or is this planned ? LA1RMA -- Håken Hveem Gnup/PGP key ID: 45793A72

3 2

Re: [chirp_users] Raspberry PI rev level.
by Bob Boehme 04 Jan '15

04 Jan '15

Yes you have to go to the chirp site and download the latest.. Raspberry site has a really old version.. From: chirp_users-bounces(a)intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Chuck Hast Sent: Saturday, January 03, 2015 10:04 AM To: Discussion of CHIRP Subject: [chirp_users] Raspberry PI rev level. I noticed that the rev level for the RasPi is 0.1.12 is there newer rev level for the RasPi? if not what do i need to get to the 0.4.1 rev level for the RasPi?

1 0

[chirp_users] Raspberry PI rev level.
by Chuck Hast 03 Jan '15

03 Jan '15

I noticed that the rev level for the RasPi is 0.1.12 is there newer rev level for the RasPi? if not what do i need to get to the 0.4.1 rev level for the RasPi?

1 0

Re: [chirp_users] UV-5R Says "Radio did not respond"
by Bob Boehme 03 Jan '15

03 Jan '15

The plug does not go all the way in on some of the newer radios... trim a bit off the side with a knife and it will go all the way in.. -----Original Message----- From: chirp_users-bounces(a)intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Richard Dillman Sent: Friday, January 02, 2015 3:55 PM To: Jim Unroe; Discussion of CHIRP Subject: Re: [chirp_users] UV-5R Says "Radio did not respond" >Hi Richard, > >Since the programming cable already works with your radio, the driver >and programming cable must be OK. This means the problem is that you >are not getting the plug fully engaged in the radio. > >Jim KC9HI Hi Jim. You are always quick to respond with helpful advice. Thanks! Yeah, I encountered that plug seating issue with my own UV-5RA so with the UV-5R radio I really put some pressure on the connector - even trimmed the plug. But no joy. So maybe a defective connector on the radio side. Best, RD ================================= Richard Dillman, T2-GB-061170 Chief Operator, Coast Station KSM Maritime Radio Historical Society http://www.radiomarine.org ================================= _______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users

1 0

[chirp_users] Account signup and FT1D
by Bret Palsson 03 Jan '15

03 Jan '15

Hi fellow CHIRP users/developers! Account signup: I never got my account verification email when registering. :( http://chirp.danplanet.com/login FT1D: I own this radio and I see support is being developed for it, just recently. I have already written a python program to dump the memory and I have decompiled the adms binary to source. I have the MemoryDataBase offsets, meanings, and code to generate the memory. Anyway I’d like to help out, I’m an software engineer with motivation to get my radio working. ;) -Bret public byte[] eepromDataArray = new byte[130496]; public Memory memData = new Memory(); public SetMode setData = new SetMode(); public Comment CommentData = new Comment(); private int memDtbsCpuType = 0; public const int EEPROM_ARRAY_SIZE = 130496; public const int EEPROM_MEM_BAND_COMMON_DATA_SIZE = 64; public const int EEPROM_MEM_BAND_SINGLE_DATA_SIZE = 128; public const int EEPROM_VFO_HONE_MEM_COMMON_DATA_SIZE = 32; public const int EEPROM_SP_TONE_SQL_DATA_SIZE = 1; public const int EEPROM_JR_SQL_DATA_SIZE = 1; public const int EEPROM_MEM_BANK_CH_NUM_DATA_SIZE = 2; public const int EEPROM_MEM_CH_DIR_DATA_SIZE = 1; public const int EEPROM_WX_MEM_AN_DATA_SIZE = 18; public const int EEPROM_BANK_NAME_DATA_SIZE = 18; public const int EEPROM_DTMF_MEM_DATA_SIZE = 16; public const int EEPROM_STATUS_TEXT_DATA_SIZE = 60; public const int EEPROM_WIRES_X_DATA_SIZE = 16; public const int EEPROM_GM_GROUP_NAME_DATA_SIZE = 16; public const int EEPROM_GM_MEMBER_NAME_DATA_SIZE = 15; public const int EEPROM_GM_MEMBER_NAME_RSV_DATA_SIZE = 5; public const int EEPROM_GM_MSG_SAVE_DATA_SIZE = 80; public const int EEPROM_GPS_POSITION_DATA_SIZE = 28; public const int EEPROM_DIGITAL_CALL_SIGN_DATA_SIZE = 10; public const int EEPROM_APRS_MYCALL_SSID_BIN_DATA_SIZE = 7; public const int EEPROM_APRS_MYCALL_SSID_STR_DATA_SIZE = 9; public const int EEPROM_APRS_MYCALL_STR_DATA_SIZE = 6; public const int EEPROM_APRS_SSID_STR_DATA_SIZE = 2; public const int EEPROM_APRS_DIGIPATH_DATA_SIZE = 8; public const int EEPROM_APRS_MSG_TEXT_DATA_SIZE = 16; public const int EEPROM_APRS_MSG_SET_DATA_SIZE = 9; public const int EEPROM1_RCV1_OFFSET = 0; public const int EEPROM1_BAND_INDIVIDUAL_BAK_A_OFFSET = 64; public const int EEPROM1_BAND_INDIVIDUAL_BAK_B_OFFSET = 576; public const int EEPROM1_SET_MODE_OFFSET = 1088; public const int EEPROM1_BAND_COMMON_OFFSET = 1472; public const int EEPROM1_BAND_COMMON_BAK_OFFSET = 1536; public const int EEPROM1_ABAND_INDIVIDUAL_OFFSET = 1600; public const int EEPROM1_ABAND_INDIVIDUAL_BAK_OFFSET = 1728; public const int EEPROM1_BBAND_INDIVIDUAL_OFFSET = 1856; public const int EEPROM1_BBAND_INDIVIDUAL_BAK_OFFSET = 1984; public const int EEPROM1_RBAND_INDIVIDUAL_OFFSET = 2112; public const int EEPROM1_RBAND_INDIVIDUAL_BAK_OFFSET = 2240; public const int EEPROM1_DTMF_MEM_OFFSET = 2368; public const int EEPROM1_RCV2_OFFSET = 2624; public const int EEPROM1_WX_MEM_AN_OFFSET = 3648; public const int EEPROM1_BANK_NAME_OFFSET = 3828; public const int EEPROM1_HOME_CH_OFFSET = 4288; public const int EEPROM1_ABAND_VFO_OFFSET = 4672; public const int EEPROM1_BBAND_VFO_OFFSET = 5056; public const int EEPROM1_MEM_BANK_CH_NUM_OFFSET = 5440; public const int EEPROM1_MEM_CH_DIR_OFFSET = 10240; public const int EEPROM1_MEM_CH_NORM_OFFSET = 11584; public const int EEPROM1_MEM_CH_SKIP_OFFSET = 40384; public const int EEPROM1_MEM_CH_RCV_OFFSET = 43552; public const int EEPROM1_MEM_CH_PMS_OFFSET = 43584; public const int EEPROM1_RCV3_OFFSET = 46784; public const int EEPROM1_SPTONE_SQL_OFFSET = 47744; public const int EEPROM1_JR_SQL_OFFSET = 47808; public const int EEPROM1_RCV4_OFFSET = 47872; public const int EEPROM1_APRS_OFFSET = 48832; public const int EEPROM1_GPS_POSI_OFFSET = 49472; public const int EEPROM1_STATUS_TEXT_OFFSET = 49760; public const int EEPROM1_RCV5_OFFSET = 50064; public const int EEPROM1_DIGITAL_OFFSET = 52928; public const int EEPROM1_RCV6_OFFSET = 53312; public const int EEPROM1_RCV7_OFFSET = 57024; public const int EEPROM1_POWER_SW_OFFSET = 65214; public const int EEPROM2_APRS_BEACON_DIR_OFFSET = 65216; public const int EEPROM2_APRS_BEACON_DATA_OFFSET = 67136; public const int EEPROM2_APRS_MESSAGE_DIR_OFFSET = 77696; public const int EEPROM2_APRS_MESSAGE_DATA_OFFSET = 79616; public const int EEPROM2_RCV1_OFFSET = 88256; public const int EEPROM2_GM_OFFSET = 114112; public const int EEPROM2_WIRES_X_OFFSET = 122304; public const int EEPROM2_RCV2_OFFSET = 126400; public const int MEMORY_NORM_DIR_OFFSET = 0; public const int MEMORY_SKIP_DIR_OFFSET = 900; public const int MEMORY_PMS_DIR_OFFSET = 1000; public const int MEMORY_WX_DIR_OFFSET = 1100; public const int MEMORY_JR_SQL_DIR_OFFSET = 1110; public const int MEMORY_INTERNATIONAL_VHF_DIR_OFFSET = 1130; public const int MEMORY_SPTONE_SQL_DIR_OFFSET = 1190; public const int MEMORY_WIRELESS_C_DIR_OFFSET = 1210; public const int MEMORY_EMERGENCY_DIR_OFFSET = 1230; public const int MEMORY_FIRE_DIR_OFFSET = 1250; public const int MEMORY_RCV_DIR_OFFSET = 1336; public const int GROUP_NAME_ORIGINAL_TBL_OFFSET = 160;

2 1

[chirp_users] UV-5R Says "Radio did not respond"
by Richard Dillman 03 Jan '15

03 Jan '15

I'm in a bit of a quandary. I volunteered to program a friend's UV-5R using Chirp, which works a treat with my UV-5RA. However when I try to download from the UV-5R Chirp complains that the radio did not respond. Since all is well with my own UV-5RA I assume the software/driver/cable are not an issue. I'm using Chirp Daily Build 20150102. All guidance will be much appreciated... especially since I promised to deliver the radio tomorrow! Thanks, RD ================================= Richard Dillman, T2-GB-061170 Chief Operator, Coast Station KSM Maritime Radio Historical Society http://www.radiomarine.org =================================

3 3

Re: [chirp_users] UV-5R Says "Radio did not respond"
by Richard Dillman 02 Jan '15

02 Jan '15

>Hi Richard, > >Since the programming cable already works with your radio, the driver >and programming cable must be OK. This means the problem is that you >are not getting the plug fully engaged in the radio. > >Jim KC9HI Hi Jim. You are always quick to respond with helpful advice. Thanks! Yeah, I encountered that plug seating issue with my own UV-5RA so with the UV-5R radio I really put some pressure on the connector - even trimmed the plug. But no joy. So maybe a defective connector on the radio side. Best, RD ================================= Richard Dillman, T2-GB-061170 Chief Operator, Coast Station KSM Maritime Radio Historical Society http://www.radiomarine.org =================================

1 0

[chirp_users] New Daily Build
by Build System 02 Jan '15

02 Jan '15

Greetings, A new daily build of CHIRP is available. This includes changes made directly to the tree yesterday, and may include additional features, bug fixes, and/or bugs. If you are interested in trying it, grab it from the following location: http://trac.chirp.danplanet.com/chirp_daily/daily-20150102 A list of the changes included in this build (since the last daily) follows: Changes for Build #315 [Marco Filippi <iz3gme.marco(a)gmail.com>] [FT1D] add image file for auto test In support of #967 [Marco Filippi <iz3gme.marco(a)gmail.com>] [FT1D] code cleanup No functional changes at all, only some code cleanup to make code look better and pylint happier In support of #159 [Jim Unroe <rock.unroe(a)gmail.com>] [VV-898] Add Settings to Leixen VV-898 Module - Part 3 Add the following settings: - Custom Display Message 1 - Custom Display Message 2 - System Message (display only) - Backlight - Key Lock Mode - A/B Select related to #2149 [Jim Unroe <rock.unroe(a)gmail.com>] [VV-898] Add Settings to Leixen VV-898 Module - Part 2 Add the following settings: - Monitor - VFO/MR - MR/CHA - Volume - User-Defined related to #2149 [Jim Unroe <rock.unroe(a)gmail.com>] [VV-898] Add Settings to Leixen VV-898 Module - Part 1 Add support infrastructure for radio settings. Add the following settings: - Automatic Power Off - Squelch Level - Scan Mode - Time Out Timer - Step related to #2149

2 1

[chirp_users] Baofeng UV-5RA cloning problem
by Tom Van de Bussche 31 Dec '14

31 Dec '14

When I try to clone my Baofeng UV-5RA, it starts the download and I receive a "radio Refused to send block 0x0140" error. I am running Chirp on windows 8.1, and Chrip is 20141231. firmware is BFB297. Any ideas or suggestions? Tom Van de Bussche KB3OA

3 5

[chirp_users] New Daily Build
by Build System 31 Dec '14

31 Dec '14

Greetings, A new daily build of CHIRP is available. This includes changes made directly to the tree yesterday, and may include additional features, bug fixes, and/or bugs. If you are interested in trying it, grab it from the following location: http://trac.chirp.danplanet.com/chirp_daily/daily-20141231 A list of the changes included in this build (since the last daily) follows: Changes for Build #314 [Jim Unroe <rock.unroe(a)gmail.com>] [VV-898] Update Image Detections (Improved) Improve method to fall back to original detection string for older data files Better detect between Jetstream, Leixen (v1.02 and v1.03) images related to #2119 [Marco Filippi <iz3gme.marco(a)gmail.com>] [FT1D] Remove more invalid chars from APRS message body Some chars are printable but not accepted as valid chars setting string To avoid exceptions remove them all from APRS message body Fix implementation of #967 [nytowl] issue #967 - add a Yaesu FT1DR driver - based on the Yaesu vx8 driver - download and upload working - memory channel and bank settings tested - Need to figure out the digital modes for the radio - most settings have been tested with the exception of the scan settings - aprs message and beacons print out

1 0

[chirp_users] Wrong data saved on pofung uv-5r
by clifton meager 27 Dec '14

27 Dec '14

When I program the tone frequency for rec. and tone type it saves as 88.5 (programmed as 203.5) and TSQL rather than tone. This happens on ch. 2. I have tone programmed only on ch. 1 and 2. None for ch. 3 and 4. The tone freq . shows correct for all transmit entries. Cliff

2 1

[chirp_users] New Daily Build
by Build System 25 Dec '14

25 Dec '14

Greetings, A new daily build of CHIRP is available. This includes changes made directly to the tree yesterday, and may include additional features, bug fixes, and/or bugs. If you are interested in trying it, grab it from the following location: http://trac.chirp.danplanet.com/chirp_daily/20141225fix A list of the changes included in this build (since the last daily) follows: Changes for Build #313 [Jim Unroe <rock.unroe(a)gmail.com>] [VV-898] Update Image Detections Add method to fall back to original detection string for older data files Add method to skip uploading settings area block for older data files related to #2119

1 0

[chirp_users] New Daily Build
by Build System 25 Dec '14

25 Dec '14

Greetings, A new daily build of CHIRP is available. This includes changes made directly to the tree yesterday, and may include additional features, bug fixes, and/or bugs. If you are interested in trying it, grab it from the following location: http://trac.chirp.danplanet.com/chirp_daily/daily-20141225 A list of the changes included in this build (since the last daily) follows: Changes for Build #312 [Dan Smith <dsmith(a)danplanet.com>] Revert previous patch temporarily until we robustify it. #2119 [Jim Unroe <rock.unroe(a)gmail.com>] [VV-898] Update Image Detections Add method to fall back to original detection string for older data files related to #2119 [Dan Smith <dsmith(a)danplanet.com>] Add updated Leixen_VV-898 image from Jim Related to issue #2119 [Jim Unroe <rock.unroe(a)gmail.com>] [VV-898] Add Support for TX Inhibited Memories #2123 Update Duplex to allow the "off" setting. Enabled programming of "odd split" memories. [Jim Unroe <rock.unroe(a)gmail.com>] [VV-898] Changing to "Low" Power Level Does Not Stick #2121 [Jim Unroe <rock.unroe(a)gmail.com>] [VV-898] Updates to Prepare for Adding User Settings #2119 Adjust the amount of memory read/written during cloning to expose settings. Improve detection of Leixen and Jetstream data file images. [Tom Hayward <tom(a)tomh.us>] ap510: Fix path setting off-by-one. #2095

1 0

[chirp_users] CHIRP on ubuntu goes rtx in TX ...why ?
by y_61＠libero.it 22 Dec '14

22 Dec '14

Normal 0 14 MicrosoftInternetExplorer4 Hi, arrived the new cable and now the uv-5r is programmed ! The old cable is dead ! when I use this new cable with windows , all ok it read and program the memories, but if I use the CHIRP on boot in Ubuntu, when I connect to the usb port this cable the RTX go on TX !!! why ? remember that I use it on windows all ok, help me, best 73 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Tabella normale"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";}

1 0

[chirp_users] New Daily Build
by Build System 20 Dec '14

20 Dec '14

Greetings, A new daily build of CHIRP is available. This includes changes made directly to the tree yesterday, and may include additional features, bug fixes, and/or bugs. If you are interested in trying it, grab it from the following location: http://trac.chirp.danplanet.com/chirp_daily/daily-20141220 A list of the changes included in this build (since the last daily) follows: Changes for Build #310 [Tom Hayward <tom(a)tomh.us>] ap510: Wait longer for data during download. #2095 [Tom Hayward <tom(a)tomh.us>] ap510: Handle uninitialized data in the digipeat alias. #2095 [Tom Hayward <tom(a)tomh.us>] ap510: cast values added to the mmap to strings, as the radio expects. #2095 [Tyler Tidman <tyler.tidman(a)draak.ca>] Fix issue #2103 - Convert tab characters to spaces in shell scripts [Tyler Tidman <tyler.tidman(a)draak.ca>] Fix issue #1995 - Put stock US marine VHF channels into real channel order [Tyler Tidman <tyler.tidman(a)draak.ca>] Fix issue #2029 - Use env in all script interpreter lines Changes for Build #311 [Dan Smith <dsmith(a)danplanet.com>] Revert /bin/env change to win32 build script This was causing the build system to fail because the cygwin /usr/bin/env doesn't seem to like the -x. Related to #2029

1 0

[chirp_users] Who used CHIRP in linux ubuntu mode ?
by y_61＠libero.it 19 Dec '14

19 Dec '14

Hi, sorry i have a baofeng UV-5R release BFS 297… ( july 2014 i buy ) I whant yo create a CHIRP on usb pen boot , I think is work on ubuntu or linux ? PLEASE In how mode I create it ? I have the programm unebootin for create with the ISO the boot chirp on the Usb pen. But, where I downoad the CORRECT ISO immage for my baofenf UV-5R BFS 297 version ? I use a comunication cable buy on amazon ( I think is a clone ) in this case with NO use windows but linux…no driver is request ? VERY IMPORTANT , after the boot whith this chirp on usb pen drive in linux, what I to do to install the driver or start the comunication for the cable to my pc ??? Or I insert the cable in a usb port and is finish ? I oper the chirp program and select in “radio” and read the data memory ? Thanks for help, best 73

3 2

Re: [chirp_users] FT-817 problem
by Dale Urban 15 Dec '14

15 Dec '14

I installed FT-817 commander and it works fine. Still not able to communicate with chirp? I'm stumped. Seems I have tried every setting and every combination of settings... Sent from my iPad > On Dec 14, 2014, at 18:48, Paul Ross <w3fis(a)comcast.net> wrote: > > >> On 12/14/2014 3:00 PM, chirp_users-request(a)intrepid.danplanet.com wrote: >> Re: FT-817 problem > > Remember that the FT-817ND has to be run in "Clone" mode -- see the > manual about this -- in order to work with Chirp. > > BTW, as a test for the cable/driver, try FT817 "Commander," or some > other program that will control the FT-817ND -- perhaps FLDIGI, or > HRD/DM780. > > 73 /paul W3FIS > > _______________________________________________ > chirp_users mailing list > chirp_users(a)intrepid.danplanet.com > http://intrepid.danplanet.com/mailman/listinfo/chirp_users

3 2

Re: [chirp_users] FT-817 problem
by chiefsfan2 15 Dec '14

15 Dec '14

Yeas I have tried them all. -----Original Message----- From: chirp_users-bounces(a)intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Jim Unroe Sent: Sunday, December 14, 2014 9:21 PM To: Discussion of CHIRP Subject: Re: [chirp_users] FT-817 problem There are two models to select from for the FT-817ND, the FT-817ND and the FT-817ND (US). Are you selecting the correct one for your radio? Jim KC9HI On Sun, Dec 14, 2014 at 10:11 PM, Dale Urban <chiefsfan2(a)cox.net> wrote: > I installed FT-817 commander and it works fine. Still not able to communicate with chirp? I'm stumped. Seems I have tried every setting and every combination of settings... > Sent from my iPad > >> On Dec 14, 2014, at 18:48, Paul Ross <w3fis(a)comcast.net> wrote: >> >> >>> On 12/14/2014 3:00 PM, chirp_users-request(a)intrepid.danplanet.com wrote: >>> Re: FT-817 problem >> >> Remember that the FT-817ND has to be run in "Clone" mode -- see the >> manual about this -- in order to work with Chirp. >> >> BTW, as a test for the cable/driver, try FT817 "Commander," or some >> other program that will control the FT-817ND -- perhaps FLDIGI, or >> HRD/DM780. >> >> 73 /paul W3FIS >> >> _______________________________________________ >> chirp_users mailing list >> chirp_users(a)intrepid.danplanet.com >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users > _______________________________________________ > chirp_users mailing list > chirp_users(a)intrepid.danplanet.com > http://intrepid.danplanet.com/mailman/listinfo/chirp_users _______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users ----- No virus found in this message. Checked by AVG - www.avg.com Version: 2014.0.4794 / Virus Database: 4235/8737 - Release Date: 12/14/14

1 0

[chirp_users] Looking for N5R-213BFB297 image.
by Simon Wex 15 Dec '14

15 Dec '14

Hey All, First of all, thanks so much for your wonderful radio community resources. I'm new to all of this, but just screwed up and so I've started actually learning! Using Chirp, I uploaded an image from one of my radios onto the same model UV-5RA radio with different firmware (oops). I now can only receive on that radio if holding the mon button. I think I need to upload an image downloaded from a radio with the same firmware and then import my local frequency list using my CSV export. The problem is, I can't find a chirp image with the right firmware version. The radio lists it as "N5R-213BFB297". I see at http://kc9hi.dyndns.org/uv5r/programming/CHIRPrecovery/ there are both N5R-213 and BFB297 images separately. When I try to upload the BFB297 image using the latest daily Chirp software (chirp-daily-20141210), I get this message: "Upload finished, but the 'Other Settings' could not be sent because the firmware version of the image ( Ver BFB297 ) does not match that of the radio (N5R-213BFB297 )." If I use the N5R-213 image, I get the following error: --- Sending Magic: 000: 50 bb ff 20 12 07 25 00 P.....%. Ident: 000: aa 36 74 04 00 05 20 dd .6t..... Image Version is 'N5R-213BFB297 ' Radio Version is 'N5R-213BFB297 ' Image Special Block is 000: ff ff ff ff ff ff ff 00 ........ Radio Special Block is 000: 38 76 03 b5 b0 26 39 00 8v...&9. -- Exception: -- Traceback (most recent call last): File "/Users/simon/Downloads/chirp-daily-20141210.app/Contents/Resources/chirp/chirpui/clone.py", line 225, in run self.__radio.sync_out() File "/Users/simon/Downloads/chirp-daily-20141210.app/Contents/Resources/chirp/chirp/uv5r.py", line 670, in sync_out _do_upload(self) File "/Users/simon/Downloads/chirp-daily-20141210.app/Contents/Resources/chirp/chirp/uv5r.py", line 527, in _do_upload radio_special_block) RadioError: Image not supported by radio: `8v��&9' ------ Clone failed: Image not supported by radio: `8v��&9' Clone thread ended --- Exception Dialog: Image not supported by radio: `8v��&9' --- Traceback (most recent call last): File "/Users/simon/Downloads/chirp-daily-20141210.app/Contents/MacOS/../Resources/chirp/chirpw", line 83, in <module> os.putenv("LANG", langs[0]) IndexError: list index out of range ---------------------------- Can I just modify the special block of the image? Any help would be much appreciated. Thanks, Simon.

4 6

[chirp_users] FT817 problem
by Nigel A. Gunn G8IFF/W8IFF 15 Dec '14

15 Dec '14

Is it not the DATA cable rather than the CAT cable you need to clone an FT-817? Nigel A. Gunn, 1865 El Camino Drive, Xenia, OH 45385-1115, USA. tel +1 937 825 5032 Amateur Radio G8IFF W8IFF (was KC8NHF 9H3GN), e-mail nigel(a)ngunn.net www http://www.ngunn.net Member of ARRL, QRPARCI #11644, SOC #548, Flying Pigs QRP Club International #385, Dayton ARA #2128, AMSAT-NA LM-1691, GCARES, EAA382.

1 0

Re: [chirp_users] FT-817 problem
by Dale Urban 15 Dec '14

15 Dec '14

Thanks for the info, I'm still unable to communicate with the radio so I will try commander for a test. Sent from my iPad > On Dec 14, 2014, at 18:48, Paul Ross <w3fis(a)comcast.net> wrote: > > >> On 12/14/2014 3:00 PM, chirp_users-request(a)intrepid.danplanet.com wrote: >> Re: FT-817 problem > > Remember that the FT-817ND has to be run in "Clone" mode -- see the > manual about this -- in order to work with Chirp. > > BTW, as a test for the cable/driver, try FT817 "Commander," or some > other program that will control the FT-817ND -- perhaps FLDIGI, or > HRD/DM780. > > 73 /paul W3FIS > > _______________________________________________ > chirp_users mailing list > chirp_users(a)intrepid.danplanet.com > http://intrepid.danplanet.com/mailman/listinfo/chirp_users

1 0

Re: [chirp_users] FT-817 problem
by Paul Ross 15 Dec '14

15 Dec '14

On 12/14/2014 3:00 PM, chirp_users-request(a)intrepid.danplanet.com wrote: > Re: FT-817 problem Remember that the FT-817ND has to be run in "Clone" mode -- see the manual about this -- in order to work with Chirp. BTW, as a test for the cable/driver, try FT817 "Commander," or some other program that will control the FT-817ND -- perhaps FLDIGI, or HRD/DM780. 73 /paul W3FIS

1 0

Re: [chirp_users] FT-817 problem
by Dale Urban 14 Dec '14

14 Dec '14

Well I tried the older driver with the same results. Any other ides where to look for a fix? Sent from my iPad > On Dec 14, 2014, at 12:06, Dale Urban <chiefsfan2(a)cox.net> wrote: > > Thank you I'll give it a try. > > Sent from my iPad > >> On Dec 13, 2014, at 19:25, Jim Unroe <rock.unroe(a)gmail.com> wrote: >> >> Hi Dale, >> >> The usual problem is that most programming cable that have Prolific >> type chips in them are not compatible with the latest Windows drivers. >> The fix is to downgrade to the v3.2.0.0 driver. >> >> http://www.miklor.com/COM/UV_Drivers.php >> >> Jim KC9HI >> >>> On Sat, Dec 13, 2014 at 7:59 PM, Dale Urban <chiefsfan2(a)cox.net> wrote: >>> I purchased a USB cable for my FT-817 from kawamall to use with chirp. The device mgr says the drivers are up to date and the device is working properly on on com port 12. I have the 817 cat data speed set at 9600 and the com port setting is 9600,8,N,1 with no flow control. I follow the instructions in cirp to download from radio and it just sets there and will not read the radio and eventually will get a no communications with the radio error msg. If I shut the radio off chirp then sends an error so it knows the radio is there. I did notice in the txt file that was with the drivers says the drivers are for a gps? Any suggestions to try would be appreciated. Thanks >> _______________________________________________ >> chirp_users mailing list >> chirp_users(a)intrepid.danplanet.com >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users > _______________________________________________ > chirp_users mailing list > chirp_users(a)intrepid.danplanet.com > http://intrepid.danplanet.com/mailman/listinfo/chirp_users

3 2

[chirp_users] please take me off of this email list
by jalex2006 14 Dec '14

14 Dec '14

2 1

Re: [chirp_users] FT-817 problem
by Dale Urban 14 Dec '14

14 Dec '14

Thank you I'll give it a try. Sent from my iPad > On Dec 13, 2014, at 19:25, Jim Unroe <rock.unroe(a)gmail.com> wrote: > > Hi Dale, > > The usual problem is that most programming cable that have Prolific > type chips in them are not compatible with the latest Windows drivers. > The fix is to downgrade to the v3.2.0.0 driver. > > http://www.miklor.com/COM/UV_Drivers.php > > Jim KC9HI > >> On Sat, Dec 13, 2014 at 7:59 PM, Dale Urban <chiefsfan2(a)cox.net> wrote: >> I purchased a USB cable for my FT-817 from kawamall to use with chirp. The device mgr says the drivers are up to date and the device is working properly on on com port 12. I have the 817 cat data speed set at 9600 and the com port setting is 9600,8,N,1 with no flow control. I follow the instructions in cirp to download from radio and it just sets there and will not read the radio and eventually will get a no communications with the radio error msg. If I shut the radio off chirp then sends an error so it knows the radio is there. I did notice in the txt file that was with the drivers says the drivers are for a gps? Any suggestions to try would be appreciated. Thanks > _______________________________________________ > chirp_users mailing list > chirp_users(a)intrepid.danplanet.com > http://intrepid.danplanet.com/mailman/listinfo/chirp_users

1 0

[chirp_users] FT-817 problem
by Dale Urban 14 Dec '14

14 Dec '14

I purchased a USB cable for my FT-817 from kawamall to use with chirp. The device mgr says the drivers are up to date and the device is working properly on on com port 12. I have the 817 cat data speed set at 9600 and the com port setting is 9600,8,N,1 with no flow control. I follow the instructions in cirp to download from radio and it just sets there and will not read the radio and eventually will get a no communications with the radio error msg. If I shut the radio off chirp then sends an error so it knows the radio is there. I did notice in the txt file that was with the drivers says the drivers are for a gps? Any suggestions to try would be appreciated. Thanks Sent from my iPad

2 1

[chirp_users] chrip + RaspberryPI + Galaxy Note
by Chuck Hast 13 Dec '14

13 Dec '14

It works great, I downloaded a x server to tbe Note, aimed it at chirp on the raspi and now i have my mobile programmer without carrying a laptop, besides the raspi is a great way to kill time in the hotel room, and keep out of trouble.

1 0

[chirp_users] Chirp and virus alarm
by Pedja YT9TP 12 Dec '14

12 Dec '14

Just for the record: I just tried to download latest daily build. Avast blocked connection claiming it is malicious, infected with Win32:Evo-gen. Tried to download both install exe and ZIP file, both were blocked. I disabled Avast, then downloaded and installed Chirp latest daily build, but when I enable Avast it does not allow Chirp to run, still claiming it is infected by Win32:Evo-gen. However, the latest stable build http://chirp.danplanet.com/download/0.4.1/chirp-0.4.1-installer.exe was not recognized as malicious and is not blocked. It downloaded and installed with no problem. I guess this is false alarm but quite annoying. Pedja YT9TP --- This email has been checked for viruses by Avast antivirus software. http://www.avast.com

4 5

[chirp_users] BF-F9 problems
by radian 12 Dec '14

12 Dec '14

Ok, so I'm a newbie Tech and am trying to figure out how to program, either manually, or with CHIRP my BF-F9 radio... so far with no good results, even with searching the internet, youtube, and trying to get the right driver to work and the CHIRP software won't recognize my radio at all.... help? -- *radian* *KG5EYN*

2 1

[chirp_users] FM mode
by Tyler Day 12 Dec '14

12 Dec '14

My chirp software is stuck on fm mode the only options to me are fm and nfm is this normal? I am trying to program repeaters into my beofeng uv5r radio. Dont I need the 2 meter option to do this? Thanks.

3 2

[chirp_users] Baofeng UV5R+ N5R-219
by D.J.J. Ring, Jr. 11 Dec '14

11 Dec '14

Hello group, I'm trying to help a friend who tried to use CHIRP and managed to have the ONLY RECEIVE when push MONI key. I cannot find FIRMWARE for N5R-219 BFB-297. He has two units, the other one is N5R-213 BFB-297 - and I can find this image. Any suggestions? David N1EA

2 1

[chirp_users] New Daily Build
by Build System 11 Dec '14

11 Dec '14

Greetings, A new daily build of CHIRP is available. This includes changes made directly to the tree yesterday, and may include additional features, bug fixes, and/or bugs. If you are interested in trying it, grab it from the following location: http://trac.chirp.danplanet.com/chirp_daily/daily-20141210 A list of the changes included in this build (since the last daily) follows: Changes for Build #308 [Dan Smith <dsmith(a)danplanet.com>] Add test image for Sainsonic AP510 for #2095 [Tom Hayward <tom(a)tomh.us>] Add support for Sainsonic AP510 APRS tracker. #2095 The Sainsonic AP510 is an integrated single-channel VHF radio and APRS tracker. This patch adds support for configuring all of the parameters of the AP510 (one channel and lots of settings). [Tom Hayward <tom(a)tomh.us>] Add bool cast and improve charset options in settings. For #2095 Previously, tests could not be done on RadioSettingValueBoolean values. This patch adds bool casting / test support so that checked boxes test True and unchecked boxes test False. RadioSettingValueString supported setting the charset, but only after initializing the value. This fails if the value contains characters not in the default charset. With this patch, the charset can be set during initialization, so when the value is set, it is tested against the appropriate charset. Changes for Build #309

1 0

[chirp_users] ALINCO DJ-X10
by raymond reese 09 Dec '14

09 Dec '14

I echo the interests of the following message! However, I am the proud owner of the Alinco DJ-X10 and it is also difficult to program. Maybe, if enough Alinco owners speak up and if there is someone out there who can program CHIRP to accept the functions of those radios, I would do the "happy dance" or an old fashion Irish jig. Thanks for all that CHIRP is so far! Ray Reese KD7KRH ==================================== Date: Sun, 7 Dec 2014 17:58:03 -0400 From: James McLellan <bordenhouse(a)gmail.com> Subject: [chirp_users] Radio request To: <chirp_users(a)intrepid.danplanet.com> Message-ID: <002201d01268$e0428920$a0c79b60$@com> Content-Type: text/plain; charset="us-ascii" I would be very grateful if you could add my trusty old Alinco DJ-V5 to the radio interface list. RT Systems <https://www.rtsystemsinc.com/alinco-handheld-radio-programming-software-s/1 857.htm> used to have a program for this radio but it has been long since discontinued and they're not interested in discussing it. The radio is robust and feature rich but, as with most handhelds, a nightmare to program manually. Thanks, Jim McLellan K5BAA ====================================

2 1

[chirp_users] Remove from list
by Tom Humphreys 08 Dec '14

08 Dec '14

Please remove me from your mailing list. Thanks. Sent from my Black and Decker toaster oven

2 1

[chirp_users] New Tech with Boafeng UV-5R and CHIRP software
by Christy Cash 08 Dec '14

08 Dec '14

Hi, and thanks for allowing me to join the group. I have been working on getting my CHIRP installed (and working) for several days now. Tonight, I FINALLY got everything to work, after trudging through many website, emails, and discussions. I created a couple of channels as a test run and everything read from the radio and wrote to the radio with no problem. I then went back into the program to start over and I got errors indicating the Port was no good. I had not removed the cable or changed ports, or done anything differently. When I went into my Devices and Printers folder, there was a yellow warning sign stating there was a problem with the port. But everything worked fine just seconds before that. I'm sure I will have more questions, but after getting this far on my own, I'm at a loss, and hope to get some help. Thank you for your time, Christy KEØCJO

4 8

[chirp_users] Radio request
by James McLellan 07 Dec '14

07 Dec '14

I would be very grateful if you could add my trusty old Alinco DJ-V5 to the radio interface list. RT Systems <https://www.rtsystemsinc.com/alinco-handheld-radio-programming-software-s/1 857.htm> used to have a program for this radio but it has been long since discontinued and they're not interested in discussing it. The radio is robust and feature rich but, as with most handhelds, a nightmare to program manually. Thanks, Jim McLellan K5BAA

1 0

Re: [chirp_users] Pofung/Baofung UV-B5 on MAC OS X
by mason fann 03 Dec '14

03 Dec '14

So I id install the 3.2.0 driver on my Windows machine at work. After that I was able to access the radio with CHIRP. Thanks for that! When I got home I tried some steps to remove/disable the existing USB driver on my MAC that I found in a thread on a forum I read too. After installing the driver for "counterfeit" Prolific cables I still got the "radio did not ack" error. I then changed the COMP (29) menu setting to ON. That seemed to do the trick! I can now access the HT with CHIRP on my preferred mac machine. Now I need to RTFM to figure out how to use a dual band radio. Never had one before. thanks for your help. Mason K0MAS On Tue, Dec 2, 2014 at 2:00 PM, <chirp_users-request(a)intrepid.danplanet.com> wrote: > Hi Mason, Did you try 3.2.0 driver model? I had to downgrade to it to get > my Kenwood TM-281 programmed. I believe it's because of the USB Prolific > chip clone from China. Hope it helps... Terry KG5EHR >

2 3

[chirp_users] Pofung/Baofung UV-B5 on MAC OS X
by mason fann 02 Dec '14

02 Dec '14

Was there ever a resolution this thread? http://intrepid.danplanet.com/pipermail/chirp_users/2014-November/006832.ht… I am having the same issues with a new Pofung(baofeng) UV-B5 on both Windows 7 and MAC OS X Mavericks with CHIRP. The OEM software works fine on Win7 for me though. There is not MAC Version so I can't do much troubleshooting on it. CHIRP does work on the MAC with a Puxing 777 and a Kenwood TH-K2 successfully. Only the UV-B5 gives the error.

2 1

[chirp_users] New Daily Build
by Build System 02 Dec '14

02 Dec '14

Greetings, A new daily build of CHIRP is available. This includes changes made directly to the tree yesterday, and may include additional features, bug fixes, and/or bugs. If you are interested in trying it, grab it from the following location: http://trac.chirp.danplanet.com/chirp_daily/daily-20141202 A list of the changes included in this build (since the last daily) follows: Changes for Build #307 [Ron Wellsted <ron(a)wellsted.org.uk>] issue #1667 code corrected for memory/vfo power setting force the mute mode to QT instead of a random value [Jim Unroe <rock.unroe(a)gmail.com>] [BF-F8HP] Add Support for N5R3401 Firmware Add support for a BF-F8HP having N5R3401/F8HP-1 firmware. Bug #2071

1 0

[chirp_users] Cable error .... what is ?
by y_61＠libero.it 01 Dec '14

01 Dec '14

i use this cable with windows xp for 4-5 months and work very well !!! i NOT update the driver, and not update by windows ! why NOW not work my cable? with CHIRP and linux it say error no2 ... what is ? in how mode i TEST in windows or CHIRP linux if the cable porgramming is good or fault ??? 73

1 0

[chirp_users] R: chirp_users Digest, Vol 71, Issue 22
by y_61＠libero.it 01 Dec '14

01 Dec '14

i use this cable with windows xp for 4-5 months and work very well !!! i NOT update the driver, and not update by windows ! why NOW not work my cable? with CHIRP and linux it say error no2 ... what is ? in how mode i TEST in windows or CHIRP linux if the cable porgramming is good or fault ??? 73 >----Messaggio originale---- >Da: chirp_users-request(a)intrepid.danplanet.com >Data: 30-nov-2014 21.00 >A: <chirp_users(a)intrepid.danplanet.com> >Ogg: chirp_users Digest, Vol 71, Issue 22 > >Send chirp_users mailing list submissions to > chirp_users(a)intrepid.danplanet.com > >To subscribe or unsubscribe via the World Wide Web, visit > http://intrepid.danplanet.com/mailman/listinfo/chirp_users >or, via email, send a message with subject or body 'help' to > chirp_users-request(a)intrepid.danplanet.com > >You can reach the person managing the list at > chirp_users-owner(a)intrepid.danplanet.com > >When replying, please edit your Subject line so it is more specific >than "Re: Contents of chirp_users digest..." > > >Today's Topics: > > 1. Re: chirp_users Digest, Vol 71, Issue 21 (Bob Fk) > 2. Re: chirp_users Digest, Vol 71, Issue 21 (Dennis Smith) > > >---------------------------------------------------------------------- > >Message: 1 >Date: Sun, 30 Nov 2014 11:01:32 +1100 >From: Bob Fk <vk2byf(a)gmail.com> >Subject: Re: [chirp_users] chirp_users Digest, Vol 71, Issue 21 >To: "chirp_users(a)intrepid.danplanet.com" > <chirp_users(a)intrepid.danplanet.com> >Message-ID: > <CAN=fXRthw8cU9_XiWqJ-pin0hxmzP7FvQg9UB34ipbuXze8r1A(a)mail.gmail.com> >Content-Type: text/plain; charset="utf-8" > >RE: IS IT MY CABLE OR MY TVR? > >Most Problems with Chirp are a problem with the USB cable driver. >Use the driver which came with the cable. >Do NOT allow Windows to update the USB driver when you plug in the >USB cable and Windows loads the USB driver. > >This is an attempt by Microsoft to stop people using cloned USB cables. > >73 Bob VK2BYF > >On 30 November 2014 at 07:00, <chirp_users-request(a)intrepid.danplanet.com> >wrote: > >> Send chirp_users mailing list submissions to >> chirp_users(a)intrepid.danplanet.com >> >> To subscribe or unsubscribe via the World Wide Web, visit >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >> or, via email, send a message with subject or body 'help' to >> chirp_users-request(a)intrepid.danplanet.com >> >> You can reach the person managing the list at >> chirp_users-owner(a)intrepid.danplanet.com >> >> When replying, please edit your Subject line so it is more specific >> than "Re: Contents of chirp_users digest..." >> >> Today's Topics: >> >> 1. chirp linux and cable to programm (y_61(a)libero.it) >> >> >> ---------- Forwarded message ---------- >> From: "y_61(a)libero.it" <y_61(a)libero.it> >> To: chirp_users(a)intrepid.danplanet.com >> Cc: >> Date: Sat, 29 Nov 2014 15:32:32 +0100 (CET) >> Subject: [chirp_users] chirp linux and cable to programm >> >> hi, >> >> my cable to programm baofeng uv-5R not work or is fault my rtx uv-5r ? >> >> in how mode i test is faut the rtx or the cable ???? >> >> >> >> i create the *CHIRP cd-live on usb boot pen...*. but if i download to >> rtx it say ERROR no 2.... what is ? >> >> in how mode i TEST the cable is not dead ??? >> >> >> best 73 >> >> >> >> >> >> i try to connect th cable via *CHIRP CD LIVE* (linux ?) and I think >> the cable is recognized? >> >> >> >> but I not very shure it is effectly recognized ?there isn?t a TEST to >> know this ? >> >> >> >> I open CHIRP and select ?downolad? is say this : >> >> >> >> AN ERROR HS OCCURRED and : >> >> >> >> Could open Port/dev/ttyUSB0 [ ERRORno2 ] >> >> >> >> No file or directory /dev/ttyusb0 >> >> >> >> >> >> ?..is correct that use this TTYUSB0 ? the others ports is not called >> ?usb? ?. >> >> >> >> And what is this ERROR no 2 ? >> >> >> >> Is FAULT and dead my usb cable or my rtx UV-5R ? >> >> >> >> Thanks very muche for help me, best 73 >> >> >> _______________________________________________ >> chirp_users mailing list >> chirp_users(a)intrepid.danplanet.com >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >> >> > > >-- >*The miracle of life is that it exists despite everything it's got going >against it.* >*Bob * >

1 0

[chirp_users] FTY-8300
by Gerry Murphy 01 Dec '14

01 Dec '14

Hi I was wondering whether anybody can tell me whether the FTY-8300 dual band two-way handheld radio is a clone of one of the models supported by CHIRP? Gerry Description: Description: cid:211522723@22122011-18AD 3/56 John Street T +61 2 9518 5901 <http://www.lifetime.net.au/> www.lifetime.net.au Leichhardt NSW 2040 F +61 2 9518 9834 gerry(a)lifetime.net.au Australia

1 0

Re: [chirp_users] chirp_users Digest, Vol 71, Issue 21
by Bob Fk 30 Nov '14

30 Nov '14

RE: IS IT MY CABLE OR MY TVR? Most Problems with Chirp are a problem with the USB cable driver. Use the driver which came with the cable. Do NOT allow Windows to update the USB driver when you plug in the USB cable and Windows loads the USB driver. This is an attempt by Microsoft to stop people using cloned USB cables. 73 Bob VK2BYF On 30 November 2014 at 07:00, <chirp_users-request(a)intrepid.danplanet.com> wrote: > Send chirp_users mailing list submissions to > chirp_users(a)intrepid.danplanet.com > > To subscribe or unsubscribe via the World Wide Web, visit > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > or, via email, send a message with subject or body 'help' to > chirp_users-request(a)intrepid.danplanet.com > > You can reach the person managing the list at > chirp_users-owner(a)intrepid.danplanet.com > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of chirp_users digest..." > > Today's Topics: > > 1. chirp linux and cable to programm (y_61(a)libero.it) > > > ---------- Forwarded message ---------- > From: "y_61(a)libero.it" <y_61(a)libero.it> > To: chirp_users(a)intrepid.danplanet.com > Cc: > Date: Sat, 29 Nov 2014 15:32:32 +0100 (CET) > Subject: [chirp_users] chirp linux and cable to programm > > hi, > > my cable to programm baofeng uv-5R not work or is fault my rtx uv-5r ? > > in how mode i test is faut the rtx or the cable ???? > > > > i create the *CHIRP cd-live on usb boot pen...*. but if i download to > rtx it say ERROR no 2.... what is ? > > in how mode i TEST the cable is not dead ??? > > > best 73 > > > > > > i try to connect th cable via *CHIRP CD LIVE* (linux ?) and I think > the cable is recognized… > > > > but I not very shure it is effectly recognized …there isn’t a TEST to > know this ? > > > > I open CHIRP and select “downolad” is say this : > > > > AN ERROR HS OCCURRED and : > > > > Could open Port/dev/ttyUSB0 [ ERRORno2 ] > > > > No file or directory /dev/ttyusb0 > > > > > > …..is correct that use this TTYUSB0 ? the others ports is not called > “usb” …. > > > > And what is this ERROR no 2 ? > > > > Is FAULT and dead my usb cable or my rtx UV-5R ? > > > > Thanks very muche for help me, best 73 > > > _______________________________________________ > chirp_users mailing list > chirp_users(a)intrepid.danplanet.com > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > > -- *The miracle of life is that it exists despite everything it's got going against it.* *Bob *

2 1

[chirp_users] chirp linux and cable to programm
by y_61＠libero.it 29 Nov '14

29 Nov '14

hi, my cable to programm baofeng uv-5R not work or is fault my rtx uv-5r ? in how mode i test is faut the rtx or the cable ???? i create the CHIRP cd-live on usb boot pen.... but if i download to rtx it say ERROR no 2.... what is ? in how mode i TEST the cable is not dead ??? best 73 Normal 0 14 MicrosoftInternetExplorer4 i try to connect th cable via CHIRP CD LIVE (linux ?) and I think the cable is recognized… but I not very shure it is effectly recognized …there isn’t a TEST to know this ? I open CHIRP and select “downolad” is say this : AN ERROR HS OCCURRED and : Could open Port/dev/ttyUSB0 [ ERRORno2 ] No file or directory /dev/ttyusb0 …..is correct that use this TTYUSB0 ? the others ports is not called “usb” …. And what is this ERROR no 2 ? Is FAULT and dead my usb cable or my rtx UV-5R ? Thanks very muche for help me, best 73 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Tabella normale"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";}

1 0

[chirp_users] Ubuntu Error
by D.J.J. Ring, Jr. 28 Nov '14

28 Nov '14

Upgrading from CHIRP TO CHIRP-Daily. dpkg: error processing archive /var/cache/apt/archives/chirp-daily_20141119~utopic~1_i386.deb (--unpack): trying to overwrite '/usr/share/applications/chirp.desktop', which is also in package chirp 0.4.0-1 dpkg-deb: error: subprocess paste was killed by signal (Broken pipe) Chirp (regular) was uninstalled first then chirp-daily from the PPA was attempted to be installed. I am helping someone with this, I am just sending this in. Does anyone see any problem with deleting /usr/share/applications/chirp.desktop to get rid of the error or is there a better way? David

4 4

[chirp_users] Cannot program Yaesu VX5R - need suggestions on how to debug.
by David Hagood 27 Nov '14

27 Nov '14

I have a Yaesu VX5R, and I cannot read the radio using CHIRP daily-20141119 under Linux. Symptoms: Set up to read the radio. Start the read, press the VFO button, and the radio shows "CLONE TX" for about a second or two, then CLONE FAIL. I've tried this with 2 cables - one that is just a Yaesu to RS-232 cable (and then using a Prolific USB to RS232 adapter, and also using a native 16550 based RS-232 port), and one that is a Yaesu to USB using a Prolific cable. I have verified my user ID can read the serial device, and have verified that the cable acts as a loop back cable using Minicom. I'd like some suggestions on what to try next to debug what is going on. Are there any flags I can set to try to get more debug information? Does anybody have a Yaesu VX5 radio image I can try to load, to see if loading works?

1 0

[chirp_users] problem programming radios
by kcrunchone hill 27 Nov '14

27 Nov '14

I still cant program the radio, it is not uploading tot he newer radios from my older img. the older img is the only one that I have, I have tried to read intot he fix but I really think I am in need of some step by step help. I am not as experienced as many of the guys on the forums and such and need a bit more guidance as to if I can flash the new radio with older frimware and the location of it if it exist. Rick -- from tdc to bdc fire is my desire F I N A O failure is not an option

3 2

[chirp_users] UV-5RA not working
by John Ebner 27 Nov '14

27 Nov '14

Stopped working properly when I downloaded the new daily build last week. John C. Ebner, Logistics Section Chief Jefferson County Department of Emergency Management 81 Elkins Road, Port Hadlock, WA 98339 My Office: 360-385-9368 Fax: 360-385-9376 After Hours- urgent: 360-385-3831, Ext 1 (JeffCom) Web site: www.jeffcoeoc.org<http://www.jeffcoeoc.org>

6 6

[chirp_users] CHIRP 20141119 and the Kenwood TH-D7(G) flashing "PF3" ?
by Red 27 Nov '14

27 Nov '14

I tried using CHIRP 20141119 with a genuine FTDI cable to read from my TH-D7(G) and the only result I could see was a mysterious "PF3" message flashing on the bottom of the THD7's screen. Does anyone know if CHIRP is known to work with the TH-D7(G) ? Or what the PF3 message means? Thanks. --Red

2 3