- Users - lists.chirpmyradio.com

[chirp_users] error Programming FT897
by Don Weber 11 Nov '15

11 Nov '15

Trying to program FT897 running win8, the prolific driver is good, I can use my other cables to program baofeng radios fine. the cable for the 897 when plugged in results in no errors, I have the latest Chirp daily build installed. when trying to download from the radio, it does not communicate at all. I set the baud rate on both the radio and the com port to make sure they are the same no luck, any other ideas for things i can try? sorry if this is dupe, the first one i got a bounce thanks

5 7

[chirp_users] UV-B5 question
by Lamar Brown 11 Nov '15

11 Nov '15

Hello group! I got a UV-B5 and I don't have any problem down loading radio to computer and then uploading program to the UV-B5. But this is what happens, if I have a repeater that has a "-" on the offset, the radio will take it and after you use it one time, the radio will by itself change all the "-" to "+" on every repeater that is in the radio. Is there any help for the radio or just use it for all the repeaters that have a "+" for the offset? Lamar KT4DLB

1 0

[chirp_users] CHIRP w/ TYT TH-UVF9?
by Jim and Connie Asp 11 Nov '15

11 Nov '15

Anyone able to use CHIRP with TYT TH-UVF9? I have radio but driver is not listed in current version drop-down menu. Tried other selections but no work. Any suggestions?

1 0

[chirp_users] inexpensive Dual Band Mobile radios?
by bill＠riess.us 10 Nov '15

10 Nov '15

As Shon, K2QT mentioned I agree that the Baofeng UV-82 series is a good choice at a low cost. They have a good build quality and have a higher duty cycle than the UV5R series. (My UV5RV2+ failed during a long rag chewing session, the UV-82 has done fine with similar sessions.) For about $15-$20 more, the UV-82HP has higher power. 7 watts as opposed to 5. For a dual band mobile, the Anytone AT-5888UV has 50 VHF and 40 UHF Watts and provides dual watch and some other features, but is ~$290.00. There are others in that price range, but the above is the only one I have experienced. The low cost radios are lower wattage (which may not matter depending on expected use), I don't know anyone that has one - so cannot comment on the quality. As you mention, if you move away from dual band, Yaesu, Kenwood, etc. can be had for <$175. Hard choices, good luck :) 73 Bill Riess Bill(a)BillRiess.com <mailto:Bill@BillRiess.com> Or Bill(a)Riess.us <mailto:Bill@Riess.us> P: +1 847 394 5312 C: +1 847 917 8479 Callsign: KW9WR

1 0

[chirp_users] error Programming FT897
by Don Weber 10 Nov '15

10 Nov '15

not sure how to reply directly to the list absent an email (was on digest mode) so did not get the message. so, I am in clone mode cable plugged in menu is set to CAT press the <> buttons while power on click OK on Chirp press the snd (C) button on ft897 it sits there for a bit, then gets error, eventually Chirp times out with error

1 0

Re: [chirp_users] inexpensive Dual Band Mobile radios?
by Mark Waggoner 10 Nov '15

10 Nov '15

Just a heads up, there is an updated version of the Juntai radio coming out shortly. John Miklor has been beta testing and says it's worth the wait. On Nov 10, 2015 7:45 AM, John LaMartina <JohnLa(a)usa.net> wrote: > > Dave, > Here is the review of the VV898 series. > http://www.miklor.com/COM/Review_BF888S.php > as well as the > http://www.miklor.com/COM/Review_KT8900.php > An updated version of the KT8900 is to be released in about 5 days. > (no bugs and more features) > > The VV898 is CHIRP compatible. > The KT8900 is not CHIRP compatible yet. > > John > > - http://www.miklor.com > > > > Sent: Tuesday, November 10, 2015 5:20 AM > To: Chirp Discussion > Subject: [chirp_users] inexpensive Dual Band Mobile radios? > > > > [This is sort of off-topic, but hinges on CHIRP support for the radio] > > > > Howdy, I'd like to get a recommendation for a dual band mobile radio for a new ham that will (probably) not use it a whole lot. But it needs to work reliably enough, even if not a lot of features. Actually less features is fine, that is just less stuff to not understand & less to forget between uses! :-) > > > > Mounting a UV5R in a car doesn't seem like a good idea. Can anyone offer anything good or bad about any "inexpensive" mobile dual band ham radio, including the Leixen VV-898 or Jetstream JT270M (apparently the same radio). It is one of the few cheap Mobile units I see on the list of CHIRP supported radios. > > http://chirp.danplanet.com/projects/chirp/wiki/Home > > Amazon reviews seem fairly ok, especially for $99. I'm interested in a CHIRP-supported radio. This is intended for an 1997 Jeep Cherokee, and a small radio is probably a better match. It does need to be a dual bander. > > > > If the cost gets anywhere even near $200, I'd just recommend the Yaesu 7900 or Yaseu 8800. But for this situation, I'm open to hearing about cheaper alternatives that I might be able to recommend until this new ham grows into the "sport". > > > > Thanks for your helpful council. > > > > 73, > > Dave Nathanson > > KG6ZJO > > > > PS: if you know of a better forum to ask about CHIRP compatible mobile radios, it's ok to shoot me a pm or direct email about it. > >

1 0

[chirp_users] Stun/kill
by Gary Runningbear 10 Nov '15

10 Nov '15

I have seen a number of the Chinese handheld that list the capability of remote stun / kill. what in the world is this all about?

2 2

[chirp_users] UV-5R
by Lamar Brown 10 Nov '15

10 Nov '15

Ok Jim you hit the nail on the head. Done what you said and its now working like it suppose to. I want to say thanks to everyone in the group who responded to my plea for help. As we say in my business, "we're now cooking with gas"! Lamar KT4DLB

1 0

[chirp_users] UV-5R Woes
by Lamar Brown 10 Nov '15

10 Nov '15

I have tried to program the UV-5R with Chirp and finally find out that I had to use a different model number to be able to even get the radio to upload to computer. I have added all my channels to the radio and downloaded to radio thinking that everything is fix. I can key the HT and it don't key the repeater. If I have it on channel mode, it shows both +- above the frequency display. It will drop the frequency down 0.600 like it suppose to. Ok if I have it on frequency mode , it shows - and drops down the 0.600 as its suppose to. Still don't key the repeater. I have a Baofeng UV-3 and it keys the repeater, I have a Yaesu FT-250 and it keys the repeater. I'm at my wits end on trying to get this HT program. If someone can please tell me what to do I will really appreciate it. Danny KT4DLB

6 11

[chirp_users] port access
by wthom1＠aol.com 09 Nov '15

09 Nov '15

which port does Chirp us to access the Internet? 73, KK4ZIU

3 2

[chirp_users] No VFO mode in VX-2r
by bill＠riess.us 09 Nov '15

09 Nov '15

I think the problem might be that you have turned off access to Memory Mode and/or the menu somehow with CHIRP. I don't have the VX-2R but try this as it seems to work with a number of different radios: 1 - Export your channel settings to a spreadsheet 2 - factory reset the radio 3 - Download a new image from the radio (preferably while in channel mode) 4 - Save the image for possible later use 5 - Import the channel settings from the spreadsheet (or load the spreadsheet and copy them to the new image) 6 - Save the new image 7 - Upload the image to the radio Please see the CHIRP documents for any steps you are not sure how to do. Hope that solves it! 73 Bill Riess Bill(a)Riess.us <mailto:Bill@Riess.us> KW9WR ------------------------------ FROM THE DIGEST: Date: Sun, 8 Nov 2015 19:42:16 -0800 From: Michal Smialowski <mooksmd(a)gmail.com> Subject: [chirp_users] No VFO mode in VX-2r To: chirp_users(a)intrepid.danplanet.com Message-ID: <CAHJ3AtMQXxk=tLV5XnQFdqBTTvWq3+A3nZOtWo=m_xx+c5Gx5g(a)mail.gmail.com> Content-Type: text/plain; charset="utf-8" I recently started using CHIRP to program my VX-2R. All went fine, have uploaded to the radio, but now the radio is stuck in Memory mode ( lock is off) and also can't get into SET mode. I have checked all the settings but can't figure out why it is doing this. I did a total reset and the VFO mode came back, so I uploaded the frequencies again with CHIRP and now can't get back into VFO mode. Any help would be much appreciated. Mike VE7SML

1 0

[chirp_users] UV5R Split "Off" function
by Richard Hanna 09 Nov '15

09 Nov '15

Has anyone else noticed that the "off" function under "Split" does not work? Tried it on my Windows and my Ubuntu operating systems. It does work on my KGUV1DP I wonder if it has to do with a firmware change by the manufacturer. Thanks Dick, K3VYY

3 4

[chirp_users] UV5R Transmit Disable Problems
by Richard Hanna 09 Nov '15

09 Nov '15

Happy to report the problem is resolved thanks to the help from Jim KC9HI. Simply some "Keyboard Turbulence"! I was not hitting enter after changing the Split to "Off". Anyway, thanks to Jim, and to the group. What a great pie of software! Dick, K3VYY

2 1

[chirp_users] No VFO mode in VX-2r
by Michal Smialowski 09 Nov '15

09 Nov '15

I recently started using CHIRP to program my VX-2R. All went fine, have uploaded to the radio, but now the radio is stuck in Memory mode ( lock is off) and also can't get into SET mode. I have checked all the settings but can't figure out why it is doing this. I did a total reset and the VFO mode came back, so I uploaded the frequencies again with CHIRP and now can't get back into VFO mode. Any help would be much appreciated. Mike VE7SML

1 0

[chirp_users] More on UV5R transmit
by Richard Hanna 09 Nov '15

09 Nov '15

A friend who has an older .img that works on his radio gave me t file to try. His works and shuts off transmit. I get this error message when I try to load his image Must be a newer version of firmware. Other than that the CHIRP software handles the radio fine. Dick, K3VYY

3 2

[chirp_users] ICOM F121
by bill 08 Nov '15

08 Nov '15

Will CHIRP work for this radio?

2 1

[chirp_users] Freq entry
by Gary Runningbear 06 Nov '15

06 Nov '15

In the UV 82L, when adding frequencies that have four to five digits to the right of the decimal point how do you get the last one or two digits in there?

6 15

[chirp_users] Yaesu FT-8800R
by Guy Immega 06 Nov '15

06 Nov '15

The Yaesu FT-8800R is listed in Chirp supported radios. However it is not available in the Mac version of Chirp: chirp-daily-20151023.app.zip <http://trac.chirp.danplanet.com/chirp_daily/LATEST/chirp-daily-20151023.app…> There is no later daily build of Chirp for Mac. Can I use the Yaesu FT-8800 listing in Chirp for the FT-8800R? 73, Guy Immega VA7GI

2 2

[chirp_users] Radio Not Communicating With Laptop
by Ray Nelson 06 Nov '15

06 Nov '15

I've downloaded the software & installed. I keep getting error message the radio is not connected. What am I doing wrong? Sent from my iPad

6 10

[chirp_users] Help with Chirp and Alinco DR 235
by Deane Bouvier 06 Nov '15

06 Nov '15

I have good communications between the computer and the radio. It reads and writes successfully, except ... I get an error message on write even though the radios says "PASS". The error message is " An error has occurred. Failed to communicate with radio. 'Serial' object has not attribute 'read'." I did a full reset, downloaded and installed the latest Chirp version and it still says the same thing. I am running Windows 7. The other strange thing the radio does now is that it shows empty channels with the VFO contents and the 'M' blinking when in the memory mode. That hasn't happened before. There is nothing in the menu settings related to this and I cannot find anything regarding this new feature in the manual. Any help would be appreciated. N5DQ

1 0

[chirp_users] Yaesu FT-8800R
by Guy Immega 05 Nov '15

05 Nov '15

The Yaesu FT-8800R is listed in Chirp supported radios. However it is not available in the Mac version of Chirp: chirp-daily-20151023.app.zip <http://trac.chirp.danplanet.com/chirp_daily/LATEST/chirp-daily-20151023.app…> There is no later daily build of Chirp for Mac. Can I use the Yaesu FT-8800 listing in Chirp to program the FT-8800R? Will this work? 73, Guy Immega VA7GI

1 0

Re: [chirp_users] cannot load on HP Laptop
by kc6iih 05 Nov '15

05 Nov '15

Works good on my Dell Inspiring Laptop with 64 bit Windows 10. Jock KC6IIH Jock A. Soutar KC6IIH Sent via the Samsung Galaxy S™ III, an AT&T 4G LTE smartphone <div>-------- Original message --------</div><div>From: Bill Beyrer <bbeyrer(a)comcast.net> </div><div>Date:11/05/2015 12:34 PM (GMT-08:00) </div><div>To: chirp_users(a)intrepid.danplanet.com </div><div>Subject: [chirp_users] cannot load on HP Laptop </div><div> </div>I am sure this has been covered a million times BUT I cannot get Chirp to run on my HP6540 laptop running 32 bit Win 10. Acts as if a permission problem, maybe? but the the tiny circle of death and then nothing. works on both my desktops (one Win 7 and one Win10) any help would be appreciated -- Bill Beyrer K3ZIV P O Box 382 Chambersburg, PA 17201 (717) 267-1378 _______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com

2 1

[chirp_users] cannot load on HP Laptop
by Bill Beyrer 05 Nov '15

05 Nov '15

I am sure this has been covered a million times BUT I cannot get Chirp to run on my HP6540 laptop running 32 bit Win 10. Acts as if a permission problem, maybe? but the the tiny circle of death and then nothing. works on both my desktops (one Win 7 and one Win10) any help would be appreciated -- Bill Beyrer K3ZIV P O Box 382 Chambersburg, PA 17201 (717) 267-1378

1 0

[chirp_users] how baofeng programm used ? (IW2GJV)
by Richy Brown 05 Nov '15

05 Nov '15

as others have said chirp is much better..... however if you still wish to use the baofeng "VIP" software a couple of things you will need to know are 1) it is 2 languages (english and chineese) and usually defaults to chineese so all menus are "??" the 2nd menu *from the right* is the language selector. 2) you will need the lead in and drivers installed *before* you start the VIP program as if it cant find the lead the program will open close open close open close forever i have both programs on windows 8 and chirp has neither of these problems and is much better. 73 M0RKY > -----Original Message----- > From: IW2GJV via chirp_users <chirp_users(a)intrepid.danplanet.com> > To: chirp_users(a)intrepid.danplanet.com > Sent: Wed, 04 Nov 2015 7:09 > Subject: [chirp_users] how baofeng programm used ? > > 3 november 2015 > > hi, for windows 7 and UV-5R version BFS-297 (june 2014) > > how version of VIP program original from BAOFENG (not chirp ) i download > to use > on windiows 7 ? > > thnaks to help , 73 -- Yours Richy B This email is confidential and intended solely for the use of the individual(s) it is addressed to. If you have received this email in error please let me know.

1 0

[chirp_users] Display Channel Name on Baofeng not loading from Chirp
by Snow, David 04 Nov '15

04 Nov '15

I tried to change the settings for channel mode to display the NAME vai Chirp on my Baofeng GT3 and it didn't load. It works manually via the menu system. GT3 shows up as a UV5R. *--David W. Snow*

2 1

[chirp_users] how baofeng programm used ?
by IW2GJV 04 Nov '15

04 Nov '15

3 november 2015 hi, for windows 7 and UV-5R version BFS-297 (june 2014) how version of VIP program original from BAOFENG (not chirp ) i download to use on windiows 7 ? thnaks to help , 73

2 1

Re: [chirp_users] IC-92AD Download - too many memories
by wenlock.burton 03 Nov '15

03 Nov '15

Have to check, not running any version in Windows. I'm running the Windows version in Wine as Windows 8.1 is a pain at the moment. Wenlock Sent from Samsung tablet -------- Original message -------- >From Jim Unroe <rock.unroe(a)gmail.com> Date: 03/11/2015 12:58 (GMT+10:00) To Discussion of CHIRP <chirp_users(a)intrepid.danplanet.com> Subject Re: [chirp_users] IC-92AD Download - too many memories Are you running the same daily build of CHIRP in both operating systems? The latest is CHIRP daily-20151023. Jim KC9HI On Mon, Nov 2, 2015 at 8:48 PM, Wenlock Burton <wenlock.burton(a)hotmail.com> wrote: > Still trying to figure out what's going wrong here, double checked the A > band has 800 memories (0-799) and Chirp (running in Ubuntu 14.04 LTS) is > reading 0-849 then has a problem retrieving name data for memory 849. > > This prevents it downloading the memory names and D-Star settings. > > Windows version running in Wine is reading 0-799 for the A band and > retrieves all data OK. > > Thanks > > Wenlock > VK3YWB > > _______________________________________________ > chirp_users mailing list > chirp_users(a)intrepid.danplanet.com > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > To unsubscribe, send an email to > chirp_users-unsubscribe(a)intrepid.danplanet.com _______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com

1 0

[chirp_users] FT-60 and CP2102
by Steve Whitehead 02 Nov '15

02 Nov '15

Turns out it looks like most of the CP2102 USB adapters are 3.3V output. Specifications for TTL logic is 5V. I have ordered a CP2102 that has both so we'll try that and see what happens. In the dim times (when we used a kerosene lamp to illuminate our computer screens) a common practice was to use a Max232 to convert RS232 levels to TTL for programming radios when you did not want to purchase a $40 cable from RT systems. It was often hit and miss if the radio would work because the levels were sometimes not quite right..... Should have the different CP2102 this week and report back. >Thanks for the response Jim. I wish it as easy as finding a short. > I have three of the converted 6-in-1 cables and the behavior is the same. >I will keep playing with it. I did not order the cheapest available CP2102 >available from China and notice there are several different styles. >Perhaps this one is somehow different in levels or buffering from the >others. I have read online others have had success programming the >FT-60 with the CP2102 so something is different. One thing of note is >this is one of the CP2102s that John said has the TXD and RXD switched. >On Fri, Oct 30, 2015 at 8:25 AM, Steve Whitehead <nv7vham(a)gmail.com> wrote: > > I have been using one of the 6-in-1 programming cables with the counterfeit > Prolific chip in it. After reading John Miklor's article about using the > CP2102 > in place of the Prolific counterfeit I replace the chip with the CP2102. > > The cable works perfectly with the UV-5R radios but no longer works with the > Yaesu FT-60. It is the same with my MacBook Pro or if I use FT-60 > commander. > I thought before I start spending several hours chasing this down I would > ask > if anyone else has run into this. > > Thanks, -- Please note new e-mail address nv7vham(a)gmail.com

3 3

[chirp_users] Icom IC-2100H & CHIRP
by raymond reese 02 Nov '15

02 Nov '15

I have two ICOM IC-2100H radios and I am having problems accessing their programming. CABLE: Valley Enterprises: RPC=IV8-UF (Icom USB OPC-478 FTDI). I have downloaded and installed the associated driver, according to the web address on the package. DEVICE MANAGER REPORTS: ----------------------------------------------- USB Serial Port (COM7). Device Provider: FTDI. *Driver Date: 8-26-2014. *Driver Version: 2.12.0. BPS: 9600. Data Bits: 8. Parity: None. Stop Bits: 1. Flow Control: None. *NOTE: Is there a newer driver? CHIRP SETUP: ----------------------- Port: COM7. Vendor: Icom. Model: IC-2100H. RADIO SETUP: ----------------------- 1. Turn On, Holding M/CALL Button - then displays CLONE. 2. Pressing the S-MW button - then displays CLONE OUT. 3. And then followed by ////... (indicator) showing data being sent. PROBLEM: ----------------- I have initiated Icom's sending mode, followed by Chirp's receiving mode. I have initiated Chirp's receiving mode, followed by Icom's sending mode. In both cases, I get the following error: "An error has occurred" "Failed to communicate with radio: Unexpected response from radio" QUESTIONS: -------------------- What am I doing wrong? Is there a BPS rate issue between the Icom and Chirp? If so, how do I solve it? Am I using the wrong cable, since the Operator's Manual makes reference to another cable identified as OPC-474? Also, where do I find the "CS-2100 Cloning Software", as mentioned in the Operator;s Manual, do I really need it and if so, why? 73's KD7KRH Ray

1 0

Re: [chirp_users] Adding freqs.
by kc6iih 02 Nov '15

02 Nov '15

Technically speaking the Baeofeng radios are illegal on FRI and GMRS. Reason is that they have antennas that can be removed and their power levels. JOCK KC6IIH Sent from my Samsung Galaxy Tab®|PRO -------- Original message -------- From: Gary Runningbear <runningbear2000(a)gmail.com> Date:11/01/2015 11:06 PM (GMT-08:00) To: Discussion of CHIRP <chirp_users(a)intrepid.danplanet.com> Subject: Re: [chirp_users] Adding freqs. Thanks for your reply. I am aware of a stock config list for GMRS and FRS. how can I specify for those to go into channels 16 - 38. I have tried everything I can think of and they still go into channels 1 through 22. On Nov 2, 2015 12:55 AM, "Eric Vought" <evought(a)pobox.com> wrote: You want to use the "stock config" feature. This allows you to import a standard collection of channels at once. Go to the File menu and "Open Stock Config". You can also create your own stock configs for reuse. On Sun, Nov 1, 2015 at 11:32 PM, Gary Runningbear <runningbear2000(a)gmail.com> wrote: I am trying to program a UV 82l. I have the first 16 channels already taken care of. In the next 22 channels I want to put in the GMRS and FRS frequencies. I want to be able to put all of them in at once without having to do them one at a time. Can someone tell me how to do that please. any help would be greatly appreciated. thank you. _______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com _______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com

3 3

[chirp_users] Adding freqs.
by Gary Runningbear 02 Nov '15

02 Nov '15

I am trying to program a UV 82l. I have the first 16 channels already taken care of. In the next 22 channels I want to put in the GMRS and FRS frequencies. I want to be able to put all of them in at once without having to do them one at a time. Can someone tell me how to do that please. any help would be greatly appreciated. thank you.

3 3

[chirp_users] latest chirp build
by wthom1＠aol.com 01 Nov '15

01 Nov '15

Just loaded latest Chirp build on clean install Win 7. When I do a Repeaterbook query, the mouse pointer turns to a hour glass and sits there until I close Chirp. Just like it can't an Internet connection. Pls advise. William

5 5

Re: [chirp_users] FT-60 and CP2102
by Steve Whitehead 31 Oct '15

31 Oct '15

Thanks for the response Jim. I wish it as easy as finding a short. I have three of the converted 6-in-1 cables and the behavior is the same. I will keep playing with it. I did not order the cheapest available CP2102 available from China and notice there are several different styles. Perhaps this one is somehow different in levels or buffering from the others. I have read online others have had success programming the FT-60 with the CP2102 so something is different. One thing of note is this is one of the CP2102s that John said has the TXD and RXD switched. On Fri, Oct 30, 2015 at 8:25 AM, Steve Whitehead <nv7vham(a)gmail.com> wrote: > > I have been using one of the 6-in-1 programming cables with the counterfeit > Prolific chip in it. After reading John Miklor's article about using the > CP2102 > in place of the Prolific counterfeit I replace the chip with the CP2102. > > The cable works perfectly with the UV-5R radios but no longer works with the > Yaesu FT-60. It is the same with my MacBook Pro or if I use FT-60 > commander. > I thought before I start spending several hours chasing this down I would > ask > if anyone else has run into this. > > Thanks, > > Steve, >I assume that this is one of those 6-in-1 programming cables that you >must plug in the correct adapter based on the radio that you are going >to program. That would mean that you use a different adapter for the >UV-5R than you do the FT-60. My guess is that the adapter for the >FT-60 has gone bad. It is probably only a coincidence that it happened >when the USB end was swapped out with a module containing a CP2102 >chip. You might check the FT-60 adapter with a volt-ohm-meter for >shorts or opens. >Jim KC9HI -- Please note new e-mail address nv7vham(a)gmail.com

1 0

[chirp_users] UV-6 programming
by slynchmob＠aol.com 30 Oct '15

30 Oct '15

My UV 6 Baofeng will not respond to up load to chirp I have the right drivers loaded and the wire seem to go all the way in same wire is use for uv82 with no problem

4 5

[chirp_users] FT-60 and CP2102
by Steve Whitehead 30 Oct '15

30 Oct '15

I have been using one of the 6-in-1 programming cables with the counterfeit Prolific chip in it. After reading John Miklor's article about using the CP2102 in place of the Prolific counterfeit I replace the chip with the CP2102. The cable works perfectly with the UV-5R radios but no longer works with the Yaesu FT-60. It is the same with my MacBook Pro or if I use FT-60 commander. I thought before I start spending several hours chasing this down I would ask if anyone else has run into this. Thanks, -- <nv7vham(a)gmail.com>

2 1

Re: [chirp_users] Mac user - inconsistent ability to contact radio
by Paul Slootweg 29 Oct '15

29 Oct '15

OK, after some more playing around, I think in my case the problem is indeed mechanical. I have 2 cables. The one that came with the radio and a Baofeng branded one I bought when I couldn't get the first one to work with the Mac. I now think the original issue was not having the right Prolific chip drivers, but as I then changed the cable as well, *that* became the problem. Going back to my original cable, and it works every time. (Except after first plugging in - seems that until Chirp has tried to communicate the ports are in the wrong configuration, and it opens up the mic.) So my - so far - way of working is: Plug cable into USB Launch Chirp Try to download - this will fail Plug cable into radio (while it is off) and then turn radio on Now download (or upload, I guess - not tried yet) seems to work fine. I can turn the radio off/on and it will still load. I had attached pics of the 2 cables to show the difference but the list rejected the email :( Basically, one of them has better clearance on the casing around the sockets - and that's the one that works. On 24 October 2015 at 16:33, Paul Slootweg <paul.slootweg(a)gmail.com> wrote: > OK, after some more playing around, I think in my case the problem is > indeed mechanical. > > I have 2 cables. The one that came with the radio and a Baofeng > branded one I bought when I couldn't get the first one to work with > the Mac. > > I now think the original issue was not having the right Prolific chip > drivers, but as I then changed the cable as well, *that* became the > problem. > > Going back to my original cable, and it works every time. (Except > after first plugging in - seems that until Chirp has tried to > communicate the ports are in the wrong configuration, and it opens up > the mic.) > > So my - so far - way of working is: > > Plug cable into USB > Launch Chirp > Try to download - this will fail > Plug cable into radio (while it is off) and then turn radio on > Now download (or upload, I guess - not tried yet) seems to work fine. > > I can turn the radio off/on and it will still load. > > I have attached a couple of pics that hopefully show the problem. (The > working one is the Front/Left in these pics.) > > Paul > > On 24 October 2015 at 15:07, Kearney <mbk7(a)comcast.net> wrote: >> I've had a similar issue with "Error: can't find or read the radio". Sorry, >> I have no other suggestions. I am working on a 'cheat sheet' to help avoid >> some mis-steps with CHIRP for first time users in our club so I am curios to >> find out what causes your problems. >> >> Mike KG7KIQ >> >> >> >> ----- Original Message ----- >> From: <paul.slootweg(a)gmail.com> >> To: "Discussion of CHIRP" <chirp_users(a)intrepid.danplanet.com> >> Sent: Saturday, October 24, 2015 6:46 AM >> Subject: Re: [chirp_users] Mac user - inconsistent ability to contact radio >> >> >>> Done that too - if it worked. >>> >>> The issue is connectivity to the radio. >>> >>> >>>> On 24 Oct 2015, at 14:35, Kearney <mbk7(a)comcast.net> wrote: >>>> >>>> Have you tried to download to a new file? >>>> ----- Original Message ----- >>>> From: <paul.slootweg(a)gmail.com> >>>> To: "Discussion of CHIRP" <chirp_users(a)intrepid.danplanet.com> >>>> Sent: Saturday, October 24, 2015 6:21 AM >>>> Subject: Re: [chirp_users] Mac user - inconsistent ability to contact >>>> radio >>>> >>>> >>>>> Nope. Same radio. (One of the times that download did work!) >>>>> >>>>> Paul >>>>> >>>>>> On 24 Oct 2015, at 14:12, Kearney <mbk7(a)comcast.net> wrote: >>>>>> >>>>>> >>>>>> Paul, was your original img. file created on a different radio? >>>>>> >>>>>> Mike KG7KIQ >>>>>> >>>>>> >>>>>> >>>>>> ----- Original Message ----- >>>>>> From: "Paul Slootweg" <paul.slootweg(a)gmail.com> >>>>>> To: "Discussion of CHIRP" <chirp_users(a)intrepid.danplanet.com> >>>>>> Sent: Friday, October 23, 2015 1:15 AM >>>>>> Subject: Re: [chirp_users] Mac user - inconsistent ability to contact >>>>>> radio >>>>>> >>>>>> >>>>>>> I would have assumed that if the was a compatibility problem, then the >>>>>>> cable/drivers would work 'never', not 'sometimes'. >>>>>>> >>>>>>> As for FTDI cables - unobtanium in the UK. >>>>>>> >>>>>>> Paul >>>>>>> >>>>>>>> On 21 October 2015 at 17:00, Jim Unroe <rock.unroe(a)gmail.com> wrote: >>>>>>>> On Wed, Oct 21, 2015 at 9:43 AM, Paul Slootweg >>>>>>>> <paul.slootweg(a)gmail.com> >>>>>>>> wrote: >>>>>>>>> I have the latest of everything installed, the Prolific drivers show >>>>>>>>> up as started in the Console, and the USB serial device shows up, >>>>>>>>> but >>>>>>>>> I can rarely download (never mind upload.) >>>>>>>>> Radio is UV-5RA >>>>>>>>> >>>>>>>>> Am I missing something? >>>>>>>>> >>>>>>>>> Paul >>>>>>>> >>>>>>>> Paul, >>>>>>>> >>>>>>>> When it comes to Prolific drivers, you don't want the latest. They >>>>>>>> are >>>>>>>> incompatible with the unauthorized Prolific chip copies that are in >>>>>>>> most programming cables (including the "genuine" Baofeng programming >>>>>>>> cable). Try the generic drivers on the MacOS_Tips page or purchase >>>>>>>> the >>>>>>>> 3rd party driver. >>>>>>>> >>>>>>>> http://chirp.danplanet.com/projects/chirp/wiki/MacOS_Tips >>>>>>>> >>>>>>>> https://www.mac-usb-serial.com/ >>>>>>>> >>>>>>>> Or to avoid the hassle of finding and installing a compatible driver, >>>>>>>> get a programming cable with the FTDI chip. >>>>>>>> >>>>>>>> http://www.amazon.com/gp/product/B00HUB0ONK >>>>>>>> >>>>>>>> Jim KC9HI >>>>>>>> _______________________________________________ >>>>>>>> chirp_users mailing list >>>>>>>> chirp_users(a)intrepid.danplanet.com >>>>>>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >>>>>>>> To unsubscribe, send an email to >>>>>>>> chirp_users-unsubscribe(a)intrepid.danplanet.com >>>>>>> _______________________________________________ >>>>>>> chirp_users mailing list >>>>>>> chirp_users(a)intrepid.danplanet.com >>>>>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >>>>>>> To unsubscribe, send an email to >>>>>>> chirp_users-unsubscribe(a)intrepid.danplanet.com >>>>>> >>>>>> _______________________________________________ >>>>>> chirp_users mailing list >>>>>> chirp_users(a)intrepid.danplanet.com >>>>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >>>>>> To unsubscribe, send an email to >>>>>> chirp_users-unsubscribe(a)intrepid.danplanet.com >>>>> _______________________________________________ >>>>> chirp_users mailing list >>>>> chirp_users(a)intrepid.danplanet.com >>>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >>>>> To unsubscribe, send an email to >>>>> chirp_users-unsubscribe(a)intrepid.danplanet.com >>>> >>>> _______________________________________________ >>>> chirp_users mailing list >>>> chirp_users(a)intrepid.danplanet.com >>>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >>>> To unsubscribe, send an email to >>>> chirp_users-unsubscribe(a)intrepid.danplanet.com >>> _______________________________________________ >>> chirp_users mailing list >>> chirp_users(a)intrepid.danplanet.com >>> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >>> To unsubscribe, send an email to >>> chirp_users-unsubscribe(a)intrepid.danplanet.com >> >> _______________________________________________ >> chirp_users mailing list >> chirp_users(a)intrepid.danplanet.com >> http://intrepid.danplanet.com/mailman/listinfo/chirp_users >> To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com

3 3

[chirp_users] Baofeng Radio
by Dave Sunde 29 Oct '15

29 Oct '15

I just bought some additional Baofeng radios (BF-F9 V2+) and am trying to program them using the latest Daily Build Chirp software. I downloaded from my old radio but when I uploaded to my new radio the labels did not come through. Am I missing something? Someone else programmed my original radio and I don't know what software they used. Everything else seems to work okay. It is just the labels that are missing. Dave Sunde KG7RYA

3 2

[chirp_users] Programmers
by Todd Hicks 28 Oct '15

28 Oct '15

Looking for programmers for these two radios: HYS TC-666 Hongda HD-8800 I lost the original CD's. Any help cross referencing these radios would be greatly appreciated.

2 1

[chirp_users] Mac woe's
by Peter Crigan 28 Oct '15

28 Oct '15

Hi There, love your work, I am new to ham radio. I have just purchased a TYT TH-9800 I have managed to make chirp work via my windows PC but I would like to use it on my mac book air. I have down loaded the latest version but it does not show the th-9800 in the drop down box. I have been trying to understand what 'daily builds' are but am lost with that one. I also saw that you say that there are some issues with Mac (surprise surprise) Any help would be greatly appreciated. I am planning on getting several other radios soon, if this software is a usefull as it appears I will be more than happy to donate to assist you with your good work. Many thanks VK3-KWB Peter Crigan Claudius Constructions Pty Ltd Office/Factory Address: 55 Boundary Road, North Melbourne Vic 3051 Postal Address : PO Box 2112, Hotham Hill Vic 3051 Phone - Office : 03-9942 7364 Fax : 03-8610 0167 Mobile : 0407 322 096 (business hours) peter(a)claudius.com.au

4 3

Re: [chirp_users] FW: Chirp not talking to radio - Ubuntu 14.04
by kc6iih 27 Oct '15

27 Oct '15

Windows 10 is great. No problems . I like the start and search windows. Good to have them back where they belong. Jock A. Soutar KC6IIH Sent via the Samsung Galaxy S™ III, an AT&T 4G LTE smartphone <div>-------- Original message --------</div><div>From: Wenlock Burton <wenlock.burton(a)hotmail.com> </div><div>Date:10/27/2015 1:43 PM (GMT-08:00) </div><div>To: Discussion of CHIRP <chirp_users(a)intrepid.danplanet.com> </div><div>Subject: Re: [chirp_users] FW: Chirp not talking to radio - Ubuntu 14.04 </div><div> </div>Hi Jim at al, Ok, found on the page relating to manual download that I need to type "chirpw" to run Chirp. Would have been helpful to have that information on the download page, but never mind, got it running now and download from the radio works fine. Btw, best thing about Linux is that I can use hardware that doesn't work in Windows. Like the adaptor for a led badge that uses a fake USB/serial chip. Another best thing is that Windows 8.1 is abusing my HD and I can't use the computer due to it. MS have been unable to offer a fix so I am now a Ubuntu user. Kind of fun finding what I can run without windows. Not too bad really! Thanks for your help and sorry to have bugged you Wenlock VK3YWB > Date: Tue, 27 Oct 2015 06:16:17 -0400 > From: rock.unroe(a)gmail.com > To: chirp_users(a)intrepid.danplanet.com > Subject: Re: [chirp_users] FW: Chirp not talking to radio - Ubuntu 14.04 > > On Tue, Oct 27, 2015 at 12:03 AM, Wenlock Burton > <wenlock.burton(a)hotmail.com> wrote: > > > > > > ________________________________ > > > > Hi, > > > > Just installed Chirp on Ubuntu 14.04 and can't get it to read anything from > > the radio. > > > > Wenlock, > > My CHIRP daily-20151023 works fine in the Ubuntu 14.4LTS virtual > machine that I created. > > Did you install CHIRP daily-20151023 from the PPA as instructed on the > CHIRP download page (see "Ubuntu Linux Users")? That will get you the > latest version of CHIRP (the same version that you most likely > downloaded and installed for "Windows"). > > Or did you install CHIRP v0.3.1 (released back in April of 2013) from > the Ubuntu Software Center? > > Jim KC9HI > _______________________________________________ > chirp_users mailing list > chirp_users(a)intrepid.danplanet.com > http://intrepid.danplanet.com/mailman/listinfo/chirp_users > To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com

1 0

[chirp_users] IC92AD Error retrieving bank names
by Wenlock Burton 27 Oct '15

27 Oct '15

Hi, I spoke too soon, Chirp read all the memories but when I clicked the Banks(Band A) tab it read bank data but the terminal reported: ERROR: 'NoneType' object has no attribute 'split' Exception in thread Thread-3: Traceback (most recent call last): File "/usr/lib/python2.7/threading.py", line 810, in __bootstrap_inner self.run() File "/usr/lib/pymodules/python2.7/chirp/ui/common.py", line 261, in run job.execute(self.radio) File "/usr/lib/pymodules/python2.7/chirp/ui/bankedit.py", line 138, in execute mappings = self.__model.get_memory_mappings(mem) File "/usr/lib/pymodules/python2.7/chirp/drivers/icf.py", line 544, in get_memory_mappings index = self._radio._get_bank(memory.number) File "/usr/lib/pymodules/python2.7/chirp/drivers/ic9x.py", line 83, in _get_bank return mem._bank AttributeError: Memory instance has no attribute '_bank' Chirp was unresponsive after that. It happened after downloading all the bank A memories, it looks like Chirp is trying to read more memory locations than the radio has. Wenlock

1 0

[chirp_users] FW: Chirp not talking to radio - Ubuntu 14.04
by Wenlock Burton 27 Oct '15

27 Oct '15

Hi, Just installed Chirp on Ubuntu 14.04 and can't get it to read anything from the radio. I have confirmed the cable works, both the RS-92 software and the Windows version of Chirp running in Wine can talk to the radio 100%. The USB to Serial cable is a genuine chip, not one of the fakes and works in Windows and Linux just not with the Ubuntu version of Chirp. It has also been used with the Icom Android app on a tablet and phone. All lines have Error in the Name field and no data is shown from the radio in any cell. Also, there doesn't appear to be any communication with the radio as the light on the adaptor doesn't light at any time. It lights when RS-92 is talking to the radio and when the Windows version of Chirp is talking to the radio. The com port is /dev/ttyUSB0, working with the other software but not with Chirp Ubuntu. If it's any help this is what repeats many times in the log file: Exception running RadioJob: 'NoneType' object has no attribute '__getitem__' -- Exception: -- Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/chirpui/common.py", line 111, in _execute result = func(*self.args, **self.kwargs) File "/usr/lib/python2.7/dist-packages/chirp/ic9x_icf.py", line 63, in get_memory return ic9x_icf_ll.get_memory(self._mmap, number) File "/usr/lib/python2.7/dist-packages/chirp/ic9x_icf_ll.py", line 123, in get_memory mmap = get_raw_memory(_mmap, number) File "/usr/lib/python2.7/dist-packages/chirp/ic9x_icf_ll.py", line 47, in get_raw_memory return MemoryMap(mmap[offset:offset+size]) TypeError: 'NoneType' object has no attribute '__getitem__' ------ Job Args: (25,) Job KWArgs: {} Job Called from: File "/usr/bin/chirpw", line 154, in <module> gtk.main() File "/usr/lib/python2.7/dist-packages/chirpui/memedit.py", line 1175, in <lambda> refresh.connect("clicked", lambda x: self.prefill()) File "/usr/lib/python2.7/dist-packages/chirpui/memedit.py", line 1036, in prefill job = common.RadioJob(handler, "get_memory", i) Thanks Wenlock VK3YWB

3 4

[chirp_users] iCloud Drive?
by Bill Cherepy 26 Oct '15

26 Oct '15

I would like to save my files to iCloud Drive, but I can’t find a way to do this. I put a couple of files there and I can’t find iCloud Drive in the Open File system in Chirp. Anyone have any ideas? Thanks, Bilol WB4WTN

10 14

Re: [chirp_users] iCloud Drive?
by kc6iih 26 Oct '15

26 Oct '15

MAC without cheese is not very good. JOCK KC6IIH Sent from my Samsung Galaxy Tab®|PRO -------- Original message -------- From: "Peter J. McClosky" <pmcclosky(a)earthlink.net> Date:10/25/2015 12:06 PM (GMT-08:00) To: Discussion of CHIRP <chirp_users(a)intrepid.danplanet.com> Subject: Re: [chirp_users] iCloud Drive? Have you tried to export it as a .csv file, and then uploading it? ----- Peter J. McClosky, N7IY Eugene, Oregon pmcclosky(a)earthlink.net n7iy(a)arrl.net http://home.earthlink.net/~pmcclosky/ On Oct 25, 2015, at 10:08 AM, Bill Cherepy <jcherepy(a)gmail.com> wrote: I guess I should have mentioned I am using a Mac. I see iCloud Drive as a folder in Finder and can move files to and from it as I do any other Folder. Bill WB4WTN On Oct 25, 2015, at 1:02 PM, Todd Bloomingdale <tbloomingdale(a)gmail.com> wrote: Bill is the Icloud drive web based or does it install a software on the computer? Reason I'm asking is I use Google Drive, and when I open such as save as or open, itbshiwsbup under the drives folder to click in. If it is exclusive web based I do not believe there is a way to have CHIRP go to a web address. On Oct 24, 2015 8:47 PM, "Bill Cherepy" <jcherepy(a)gmail.com> wrote: I would like to save my files to iCloud Drive, but I can’t find a way to do this. I put a couple of files there and I can’t find iCloud Drive in the Open File system in Chirp. Anyone have any ideas? Thanks, Bilol WB4WTN _______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com _______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com _______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com

1 0

[chirp_users] Mac user - inconsistent ability to contact radio
by Paul Slootweg 24 Oct '15

24 Oct '15

I have the latest of everything installed, the Prolific drivers show up as started in the Console, and the USB serial device shows up, but I can rarely download (never mind upload.) Radio is UV-5RA Am I missing something? Paul

6 9

[chirp_users] Change Number of Channels To Display?
by bill＠riess.us 23 Oct '15

23 Oct '15

It has been my experience that the number of channels displayed will stay to the max for the radio if you do the following: 1 Download from the radio 2 Change displayed channels to "Show Empty" (optional) 3 Set number of channels to max number for the radio 4 Save the configuration to .img file Now whenever I open that .img file it always displays them all. Note this is on a Windows (10) machine. I currently run CHiRP version daily-20151020. Hope that solves it! 73 Bill Bill(a)Riess.us <mailto:Bill@Riess.us> Callsign: KW9WR

1 0

Re: [chirp_users] Mac user - inconsistent ability to contact radio
by kc6iih 23 Oct '15

23 Oct '15

Cheap cables with bad prolific chips rarely work. JOCK KC6IIH Sent from my Samsung Galaxy Tab®|PRO -------- Original message -------- From: Ryan Tourge <ryan.tourge(a)gmail.com> Date:10/21/2015 7:31 AM (GMT-08:00) To: Discussion of CHIRP <chirp_users(a)intrepid.danplanet.com> Subject: Re: [chirp_users] Mac user - inconsistent ability to contact radio Push real hard on the connector? On Wed, Oct 21, 2015 at 9:43 AM, Paul Slootweg <paul.slootweg(a)gmail.com> wrote: I have the latest of everything installed, the Prolific drivers show up as started in the Console, and the USB serial device shows up, but I can rarely download (never mind upload.) Radio is UV-5RA Am I missing something? Paul _______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com

4 3

[chirp_users] New Daily Build
by Build System 23 Oct '15

23 Oct '15

Greetings, A new daily build of CHIRP is available. This includes changes made directly to the tree yesterday, and may include additional features, bug fixes, and/or bugs. If you are interested in trying it, grab it from the following location: http://trac.chirp.danplanet.com/chirp_daily/daily-20151023 A list of the changes included in this build (since the last daily) follows: Changes for Build #368 [Dan Smith <dsmith(a)danplanet.com>] Fix renamed ID-51A test image Fallout from #1961 [Marco Filippi <iz3gme.marco(a)gmail.com>] [FT60] Support for split offset greater then 12.75Mhz Radio stores offset in 15 bits, not 8 as previously supposed Fix #2911 [Dan Smith <dsmith(a)danplanet.com>] Add Icom ID-51A Plus test image from Eric Dropps Related to #1961 [Eric Dropps <kc1ckh(a)kc1ckh.com>] [ID-51][ID-51 Plus] Add support for ID-51 Plus/Anniversary Edition (Fix #1961) This patch adds support for the Icom ID-51 Anniversary and Plus Editions Due to memory size conflicts, this also contains an update to the ID-51 driver that enhances detetion logic. The ID-51 has also been renamed from ID-51A as the A and E editions are identical (image-wise) Confirmed and tested with both a real ID-51A Plus and an ID-51E Plus

1 0

[chirp_users] Baofeng Name Display
by Marty Boroff 23 Oct '15

23 Oct '15

I am able to download my BF-F8HP. I add an name to a repeater listed. I then upload to the radio but see no name on that memory address. Marty WD9GYM

3 3

Re: [chirp_users] Baofeng Name Display
by Kc6iih＠aol.com 23 Oct '15

23 Oct '15

Do you have the radio set to show name or frequency ? It needs to be set to channel mode, In a message dated 10/22/2015 6:01:21 P.M. Pacific Daylight Time, martin.boroff(a)gmail.com writes: I am able to download my BF-F8HP. I add an name to a repeater listed. I then upload to the radio but see no name on that memory address. Marty WD9GYM _______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com

1 0