- Users - lists.chirpmyradio.com

[chirp_users] zastone zt d9000
by Barry Molkentin 28 Mar '18

28 Mar '18

Hi I'm having trouble getting my computer to talk to my radio. Have tried another chip in the cloning cable but no luck So does Chirp have a programme to suit my radio (Zastone ZT D9000) or can I use another "radio" to trick it into working mode. The error message I get is; "did not except programme MODE" Thanks for any help Barry

2 1

[chirp_users] Is repeaterbook import broken?
by Nolan Darilek 28 Mar '18

28 Mar '18

Was entering the 40+ Travis County, TX repeaters by hand from repeaterbook, and happened to discover that Chirp supports import. Unfortunately, when I use the political region import feature, select Texas, Travis County, 2M band, I get a bunch of channels with no data and the frequency set to 0.00. Am I doing this incorrectly or is the feature no longer working? Thanks.

5 9

[chirp_users] (no subject)
by Kyle 27 Mar '18

27 Mar '18

I am a newbie programming a UV-5r2+ using CHIRP. Could you help me with how to fill in the fields in CHIRP? I am going on a week long backcountry ski trip in British Columbia. The operation area radio frequency given to me is attached below. How do fill in the fields correctly listed in the screen shot of CHIRP below? Or do I not have enough information? I can’t figure out how to get the RX 170.100 and TX 169.110 on the same memory channel. Then I am not sure if I am entering the tone correctly? Thank you! CH RX TX Band User Location Tone - RX Tone - TX 1 170.100 169.110 narrow GAH Cupola Mt 100.0 2 170.100 narrow GAH

6 7

[chirp_users] Can chirp program a kenwood tk-880h
by jquinn53 27 Mar '18

27 Mar '18

Sent via the Samsung Galaxy S® 5 ACTIVE™, an AT&T 4G LTE smartphone

2 1

[chirp_users] CHIRP user with Mac and Wouxun programming issues
by John Pancoast 27 Mar '18

27 Mar '18

Many thanks to Charley KE4QBW and Jeff for addressing my question about a programming cable for my MacBook Air. I will order one from Mark Dunkle and go from there. I’ll report back on my success. Thank you! John kc1iyc

1 0

[chirp_users] Current mac computer, older Wouxun and bad cable
by John Pancoast 27 Mar '18

27 Mar '18

I use Apple Mac computers with the latest OS - 10.13 High Sierra. I bought a used Wouxun KG-UV3D with old programming cable. Needless to say, this combination doesn’t work. I think I have 2 problems: 1) the HT doesn’t communicate with the computer, and 2) the most current CHIRP software doesn’t appear to cover the KG-UV3D, though I could be wrong. RE: #! — I have seen on youtube that many times the older programming cables need to be updated. Can any Mac users suggest the proper cable for my MacBook Air (13-inch, Mid 2012) running OSX 10.13.3 ? RE: #2 — Should I use an older/ earlier release of the CHIRP software? If so, can you help me to access it? Thank you for your attention! John

3 2

[chirp_users] Dan is the man. He'p a man out.
by Dennis Wage 26 Mar '18

26 Mar '18

I don't like the word donate. I prefer: PARTICIPATE Click here to Participate <https://goo.gl/fmFye9> intransitive verb -·pat·ed, -·pat·ing to have or take a part or share with others (in some activity, enterprise, etc.) Dennis M. Wage 245 Corum Hill Road Castalian Springs, TN 37031 (615) 310-4242 Cell (615) 562-5128 Home http://hammondb3organ.net http://overdubs.net

1 0

[chirp_users] New Daily Build
by Build System 26 Mar '18

26 Mar '18

Greetings, A new daily build of CHIRP is available. This includes changes made directly to the tree yesterday, and may include additional features, bug fixes, and/or bugs. If you are interested in trying it, grab it from the following location: http://trac.chirp.danplanet.com/chirp_daily/daily-20180325 A list of the changes included in this build (since the last daily) follows: Changes for Build #521 [Dan Smith <dsmith(a)danplanet.com>] Fix long lines in yaesu_clone.py Related to the patch for #5647 [Nicolas Pike <nicolas.jon.pike(a)gmail.com>] [FT-70] #5329 and issue #5647 Revise handling of empty chunks in yaesu_clone.py #5647 Empty chunks no longer counted towards blocks read. #5329 Can now set correct memory size read request, as no getting empty blocks. Yaesu_clone change proposed by Dan - Thanks! I have only tested it on the FT-70, would be great to see it tested on other Yaesu radios. This replaces my last submitted patch.

2 1

[chirp_users] New Daily Build
by Build System 25 Mar '18

25 Mar '18

Greetings, A new daily build of CHIRP is available. This includes changes made directly to the tree yesterday, and may include additional features, bug fixes, and/or bugs. If you are interested in trying it, grab it from the following location: http://trac.chirp.danplanet.com/chirp_daily/daily-20180313 A list of the changes included in this build (since the last daily) follows: Changes for Build #517 [Nicolas Pike <nicolas.jon.pike(a)gmail.com>] [FT-70] Banks support fixes for New Model #5329 Some pep8 fixes to Sorry. [Ray Cielencki <rayslinky(a)gmail.com>] #5635: fix formatting of previous ft1d patch [Ray Cielencki <rayslinky(a)gmail.com>] #5635: FT2D variant, fix opening message, extend smart beaconing limit [Jim Unroe <rock.unroe(a)gmail.com>] [GMRS-V1] Add support for new BTech GMRS-V1 model (2017 FCC GMRS rules) This patch adds support for the latest BaofengTech GMRS-V1 model that is compliant with the new 2017 FCC GMRS rules. #5625

4 3

[chirp_users] Help
by T Wilson 24 Mar '18

24 Mar '18

I’m at my wits end with my Mac computer. I’m not versed in the commands using the terminal and I’m not very proficient with a Mac computer either but I’m stuck with it. I have a Baofeng bf-888s and started trying to program it using a generic programming cable with no success. The computer would recognize that something was plugged in but that was it. I bought a legit FTDI cable and now the computer recognizes it with all the information included so I believe that the Mac sees it... but using chirp I get the “errno2” error message when I try to download from the radio! I’ve tried drivers, this, that, and I honestly want to throw this Mac in front of a fast moving truck on the freeway! My Mac is running “high Sierra” 10.13.1 Please help!!!!!

4 4

Re: [chirp_users] chirp_users Digest, Vol 111, Issue 13 - This just kills me (all)
by Christopher F. Beesley 24 Mar '18

24 Mar '18

I've said it before and I'll say it again. The whole concept of programmable devices that can be programmed to destruction by interfering with the 'wrong' memory is flawed from the start and I don't understand why people buy them. The whole concept of programmable devices that require the use of non-standard cables which in turn require the use of out-of-date drivers on the programming device is ridiculous. Why these radios have gained such a following is beyond me. Why most of them have not been returned for refunds the minute they exhibit the faults that I have read about on here time and time again is also beyond me. Whatever happened to Plug And Play? As an example, even the cheapest printer has more complex user-selectable parameters available than most of the programmable radios. Printers come with drivers that work, with user-friendly user-interfaces that only allow the programming of whatever is sensibly programmable, and with hardware interfaces that are connected to the programming device via standard cables available from the average supermarket down the road. When I bought my UV5R it came with a programming cable that didn't work, and an incomprehensible CD full of software that is mostly useless. When I finally got something to work the user-interface to the spread-sheet lookalike was at best clunky - I would describe it as awful. There were no instructions to speak of and no support from the suppliers. When I add up the hours I have spent and apply a reasonable hourly rate it becomes obvious that these radios are not cheap at all. I recently read somewhere that recent handhelds from at least one of the big three suffers from the same problems. That's it then - the end of amateur radio is nigh. My one regret is that me and my UV5R have contributed to that because I did not return it for a refund. (The UV5R is not a particularly good radio anyway. The colour display uses far too much power and cannot cope with bright sunlight. Mono displays are generally far better in both respects, and who really needs colour?) 73, Chris, an Amateur Radio operator since 1973. ________________________________ From: chirp_users-bounces(a)intrepid.danplanet.com <chirp_users-bounces(a)intrepid.danplanet.com> on behalf of chirp_users-request(a)intrepid.danplanet.com <chirp_users-request(a)intrepid.danplanet.com> Sent: 21 March 2018 19:00 To: chirp_users(a)intrepid.danplanet.com Subject: chirp_users Digest, Vol 111, Issue 13 Send chirp_users mailing list submissions to chirp_users(a)intrepid.danplanet.com To subscribe or unsubscribe via the World Wide Web, visit http://intrepid.danplanet.com/mailman/listinfo/chirp_users or, via email, send a message with subject or body 'help' to chirp_users-request(a)intrepid.danplanet.com You can reach the person managing the list at chirp_users-owner(a)intrepid.danplanet.com When replying, please edit your Subject line so it is more specific than "Re: Contents of chirp_users digest..." Today's Topics: 1. Re: This just kills me (ortingwing(a)aol.com) 2. Re: This just kills me (Tycen Stafford) ---------------------------------------------------------------------- Message: 1 Date: Tue, 20 Mar 2018 20:27:29 -0400 From: ortingwing(a)aol.com Subject: Re: [chirp_users] This just kills me To: chirp_users(a)intrepid.danplanet.com Message-ID: <16245f41b90-c89-6623(a)webjas-vab028.srv.aolmail.net> Content-Type: text/plain; charset="utf-8" It's not that the accessories are so much, just that the radio is so inexpensive. Since most of the radios used to cost way more than the UV5, a $50 headset was relatively cheap. The Bluetooth adapter I use is almost $200 by the time I buy the radio cable, and that doesn't include the actual headset. ? https://www.amazon.com/Sena-SR10-10-Bluetooth-Adapter-Two-Way/dp/B008R0LIHO… ? This is not an inexpensive hobby, but adapting the radios to motorcycle use is even more expensive. ? In a message dated 3/20/2018 11:34:29 AM Pacific Standard Time, dwage(a)dwage.com writes: ? This: ? https://www.amazon.com/2-Channel-Remote-Control-Transmitter-Highest/dp/B078… ? costs $15 more than a UV-5R ? Give me a break. ? Dennis M. Wage ? 245 Corum Hill Road Castalian Springs, TN 37031 (615) 310-4242?Cell (615) 562-5128?Home http://hammondb3organ.net http://overdubs.net _______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Ron at ortingwing(a)aol.com To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com

6 6

Re: [chirp_users] FT 857D
by Nick 24 Mar '18

24 Mar '18

Mine identifies the cable as ; Prolific USB to Serial Comm Port (comm 4) as the assigned port.Any help?Nick K7NQB ---------- Original Message ---------- From: Jardy Dawson via chirp_users <chirp_users(a)intrepid.danplanet.com> To: Discussion of CHIRP <chirp_users(a)intrepid.danplanet.com> Subject: Re: [chirp_users] FT 857D Date: Sat, 24 Mar 2018 10:42:29 -0700 What does Device Manager say your cable is? Jardy DawsonWA7JRD Ham Radio Message sent by... Oh who the heck really cares? On Mar 24, 2018, at 09:56, Jody Wallace <w6nla.socal(a)gmail.com> wrote: No, can't read from the radio. Win 10. I open chirp; click on radio/ download from radio; check port, vendor and model; click OK; Instructions pop up, and I follow them; after I click "Send" after about 4 seconds the radio says "Error".73'sMr. Jody Wallacew6nla.com On Sat, Mar 24, 2018 at 9:47 AM, Jardy Dawson via chirp_users <chirp_users(a)intrepid.danplanet.com> wrote: Can you read from the radio? You need to do that before you write to the radio. What operating system are you using? If Windows, check your cable on Device Manager. If it shows your cable is a Prolific, roll your driver back to 3.2.0.0. This can be found at www.miklor.com. Jardy DawsonWA7JRD Ham Radio Message sent by... Oh who the heck really cares? On Mar 24, 2018, at 09:28, Jody Wallace <w6nla.socal(a)gmail.com> wrote: I'm having trouble programming my FT 857D with Chirp. When I click "Send" on the radio, it says "Error" after a couple of seconds. Any help appreciated! 73'sMr. Jody Wallacew6nla.com_______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Jardy at jardy72(a)yahoo.com To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com _______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Jody L Wallace at w6nla.socal(a)gmail.com To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com_______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Jardy at jardy72(a)yahoo.com To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com ____________________________________________________________ Constant Fatigue Is A Warning Sign â€“ See The Simple Fix gundrymd.com http://thirdpartyoffers.netzero.net/TGL3231/5ab69207c3b92120713bbst04duc

2 1

[chirp_users] FT 857D
by Jody Wallace 24 Mar '18

24 Mar '18

I'm having trouble programming my FT 857D with Chirp. When I click "Send" on the radio, it says "Error" after a couple of seconds. Any help appreciated! 73's Mr. Jody Wallace w6nla.com

3 5

[chirp_users] New Daily Build
by Build System 24 Mar '18

24 Mar '18

Greetings, A new daily build of CHIRP is available. This includes changes made directly to the tree yesterday, and may include additional features, bug fixes, and/or bugs. If you are interested in trying it, grab it from the following location: http://trac.chirp.danplanet.com/chirp_daily/daily-20180324 A list of the changes included in this build (since the last daily) follows: Changes for Build #520 [Jim Unroe <rock.unroe(a)gmail.com>] [LT725UV] Add support for Baojie BJ-218 and clones. This patch adds support for Baojie BJ-218 and clones. It also adds VFO, DTMF and miscellaneous other settings Applies to fixes #5595, #5407 and #4645

1 0

Re: [chirp_users] This just kills me... chirp_users Digest, Vol 111, Issue 15
by Christopher F. Beesley 23 Mar '18

23 Mar '18

Firstof all .CSV is NOT a microsoft format, end of story. In fact, it hardly justifies being called a format when the only thing that makes it different from any old text is a lot of commas. The .DOC format is not microsoft either, I believe they stole it from WordStar in the same way that they stole the name PageMaker, mangled RS232 hardware handshaking, and failed completely to wire a DIN plug properly on their early keyboards. Thanks to Brandon Clark, P? P?, and others for their support re: This just kills me... Trevor Holyoak - I feel that you have given me an unjustified low score on technical aptitude, please allow me to correct that impression. I have worked as an Electronics Design Engineer for most of my working life. As a hobbyist, I have built radios from scratch, I have worked with valves ranging in size from Nuvistors to 4CX250B's and all sorts of transistors. I have modified the Trio 2300G, the Liner 2, and a wartime VHF Tx/Rx of uncertain origin that tuned the IF using a variable capacitor in each IF stage to select stations. I once put together a rats'-nest PLL using a popular chip of the early 80's and then wrote a program on the BBC Micro to prove that it would decode packet radio signals. I put the extra 'dot' on the frequency display of the Icom IC211E and modified the fast/slow tuning button to make it push on/push off. There were many many more such modifications and experiments back then. I also made a strobe light using the Xenon tube out of an old camera flash gun. It wouldn't work with the trigger voltage provided inside the flash gun, but hooking it up to a handy motorcycle ignition coil solved that little problem! The only thing was that when I touched the metal shaft of the speed control pot I got a bit of a tingle up my arm. This made the strobe light difficult to use - a leather glove helped but was not ideal. I used a PIC microcontroller to enable me to plug an analogue joystick into a mouse port, so I could then fly the virtual Sopwith Camel properly! I wrote the program for that little device, it worked a treat! The hardware just fitted into the really small size of die-cast aluminium box, the long thin one, complete with a 9-way 'D' connector at each end. Powered by the computer mouse port, it needed no batteries. The point is, all of those modifications provided IMPROVEMENTS to existing equipment and the experiments provided USEFUL RESULTS which could either be expanded, or would suggest that the whole idea should be abandoned. Neither the modifications nor the experiments were required because the brand-new paid-for equipment did not work straight out of the box. I did not need to scratch around searching for third-party software because the supplied software was no good, all in Chinese, or both. None of the modifications or experiments were a waste of my time, time which should never have been required in the first place. And this is where the difference is between all those things and the Chinese radios that sparked this discussion. The radios waste my time unnecessarily, it is time that has to be used in order to make the radios work properly. No improvements are made, and no useful results are obtained. I also repair motorcycle electrical systems and restore vintage reel-to-reel tape recorders amongst many other practical activities. Life isn't all about electronics! Now I see that you have to use an old version of Python to run Chirp on some computers! Don't get me wrong, I think Chirp is great. But I have to feel sorry for Dan at times... 73 all, Chris ________________________________ From: chirp_users-bounces(a)intrepid.danplanet.com <chirp_users-bounces(a)intrepid.danplanet.com> on behalf of chirp_users-request(a)intrepid.danplanet.com <chirp_users-request(a)intrepid.danplanet.com> Sent: 23 March 2018 19:00 To: chirp_users(a)intrepid.danplanet.com Subject: chirp_users Digest, Vol 111, Issue 15 Send chirp_users mailing list submissions to chirp_users(a)intrepid.danplanet.com To subscribe or unsubscribe via the World Wide Web, visit http://intrepid.danplanet.com/mailman/listinfo/chirp_users or, via email, send a message with subject or body 'help' to chirp_users-request(a)intrepid.danplanet.com You can reach the person managing the list at chirp_users-owner(a)intrepid.danplanet.com When replying, please edit your Subject line so it is more specific than "Re: Contents of chirp_users digest..." Today's Topics: 1. This just kills me.... (P? P?) 2. Re: chirp_users Digest, Vol 111, Issue 14 (Brandon Clark) 3. Re: chirp_users Digest, Vol 111, Issue 14 (Trevor Holyoak) 4. iso usb problems (Phil) 5. Re: iso usb problems (Chuck Hast) 6. Re: chirp_users Digest, Vol 111, Issue 14 (Nigel A. Gunn G8IFF/W8IFF) 7. Re: iso usb problems (Nigel A. Gunn G8IFF/W8IFF) 8. Re: chirp_users Digest, Vol 111, Issue 14 (Aubrey Turner) 9. Re: chirp_users Digest, Vol 111, Issue 14 (John Kemker) 10. Re: chirp_users Digest, Vol 111, Issue 14 (Al Jones) 11. Re: chirp_users Digest, Vol 111, Issue 14 (Nigel A. Gunn G8IFF/W8IFF) 12. Re: chirp_users Digest, Vol 111, Issue 14 (Aubrey Turner) 13. Re: iso usb problems (Jim Unroe) 14. Re: chirp_users Digest, Vol 111, Issue 14 (Dan Brown) 15. Re: Chirp wont launch in MacOS (Neil Harrington) 16. Re: chirp_users Digest, Vol 111, Issue 14 (Nigel A. Gunn G8IFF/W8IFF) 17. Re: iso usb problems (Glenn At Home) 18. Re: chirp_users Digest, Vol 111, Issue 14 (Tom Henderson) ---------------------------------------------------------------------- Message: 1 Date: Thu, 22 Mar 2018 13:32:43 -0700 From: P? P? <lr60(a)yahoo.com> Subject: [chirp_users] This just kills me.... To: "chirp_users(a)intrepid.danplanet.com" <chirp_users(a)intrepid.danplanet.com> Message-ID: <20180322203246.E2C7324F60(a)intrepid.danplanet.com> Content-Type: text/plain; charset="utf-8" The problem with programming the radios has nothing to do with the radios or the software. It is because of WAR!!! If you look at the start end of your radio programming CABLE, you will see a bulbous end which contains a small USB-TTL converter. The Manufacturers of those ?chips? also wrote software to handle the conversion process. Along comes ANOTHER Chinese Manufacturer who reverse engineers the chips (without paying for R+D) and puts them out for even cheaper. The original chip maker then puts out software that will identify the fake chips and fail to operate, thus creating the problems for hams. Even the radio manufacturers have jumped on the cheap bandwagon and incorporated the fake chips in their own cables. So, WAR has broken out, back and forth. (I converted most of mine to FTDI chips as they have the fewest driver issues.) There is a trend in even more recent radio makers to provide a straight thru cable with NO USB-TTL chip in the cable. All that is done in the radio and the makers have full control over that in their OWN software. So far I have seen this in the Radioddity?s GD-77 and RD-5R. Unfortunately, (HINT, HINT, HINT) CHIRP won?t work with these DMR radios (YET???!!!) So, the moral of this story is WAR is BAD! (Or CHIRP, please rid me of the quirks of Chinese software.) NH6BF Sent from Mail for Windows 10

1 0

Re: [chirp_users] chirp_users Digest, Vol 111, Issue 15
by Brandon Clark 23 Mar '18

23 Mar '18

Not to interrupt this fascinating discussion on who owns csv files, but to get back to the point . . . As one respondent correctly pointed out, ham radio is supposed to require some technical attitude. I think that's true, and that it is a good thing for the hobby. However, my opinion is that the difficulty of interfacing with and programming radios exists because the process is fundamentally overcomplicated and cumbersome, not because it requires more skill than some hams have. It's just a bad model for how to accomplish the process, and we all know it hurts the hobby by discouraging new hams. By comparison, I could buy a $50 burner phone and a $5 USB cord and interface that phone with any modern computer system to transfer data. Plug and play. Middle school kids build $30 raspberry pi systems that log weather, track motion, and do all kinds of cool things. But to program a $1,000 radio I have to search eBay for a cable, locate drivers somewhere in the bowels of the internet, and then download an image from the device. Honestly ask yourself this, if you had to do all these steps in order to get music downloaded on your phone how many people would just say, "heck no, it isn't worth it!" Probably a lot. Ham radio is all about finding challenges; that's true. But if the hobby is going to survive long term there has to be accessible avenues to at least get started in the hobby. HT and mobile rigs can't be using 80's tech forever, or it will make us look like dinosaurs, and keep new hams away. Let them build radios from kits, terminate cables, and make homebrew vacuum tubes from bubble gum and shot glasses when they get more advanced. Brandon

4 4

Re: [chirp_users] chirp_users Digest, Vol 111, Issue 14
by Brandon Clark 23 Mar '18

23 Mar '18

> > I couldn't agree more with your observations Chris. The state of programming in ham radio is embarrassing at best, I would bet that everyone on this board knows someone who started in radio, got a handheld, and then left the Hobby and discussed because they could not get it programmed. That kind of thing is not at all uncommon and goes beyond embarrassing to the point of being harmful to the Hobby. The problem in radio right now is that every manufacture insists on being an island and not working together. System Fusion, d-star, p25, and so forth. These are all great modes that have their place but where is the manufacturer willing to put their pride down and openly allow licensing to everybody to use "their" mode? And everyone wonders why digital voice never catches on. The programming situation is even worse. The only radio I have owned which uses a standard USB cable is a Kenwood aprs HT. Not exactly an entry-level radio. And in the complexities of software, and it becomes a nightmare. Radios needs to behave like phones, plug them into the computer with a USB cable and then simply drag and drop your CSV file into the right folder for the radio to read it. Not exactly state-of-the-art technology these days, yet ham radio manufacturers are still reliving the 80s. How many of those new hands who quit the hobby would still be hands if they could program as easily as they could save photos on their cell phone? Brandon > > I've said it before and I'll say it again. The whole concept of > programmable devices that can be programmed to destruction by interfering > with the 'wrong' memory is flawed from the start and I don't understand why > people buy them. The whole concept of programmable devices that require the > use of non-standard cables which in turn require the use of out-of-date > drivers on the programming device is ridiculous. Why these radios have > gained such a following is beyond me. Why most of them have not been > returned for refunds the minute they exhibit the faults that I have read > about on here time and time again is also beyond me. Whatever happened to > Plug And Play? > > As an example, even the cheapest printer has more complex user-selectable > parameters available than most of the programmable radios. Printers come > with drivers that work, with user-friendly user-interfaces that only allow > the programming of whatever is sensibly programmable, and with hardware > interfaces that are connected to the programming device via standard cables > available from the average supermarket down the road. When I bought my UV5R > it came with a programming cable that didn't work, and an incomprehensible > CD full of software that is mostly useless. When I finally got something to > work the user-interface to the spread-sheet lookalike was at best clunky - > I would describe it as awful. There were no instructions to speak of and no > support from the suppliers. > > When I add up the hours I have spent and apply a reasonable hourly rate it > becomes obvious that these radios are not cheap at all. > > I recently read somewhere that recent handhelds from at least one of the > big three suffers from the same problems. That's it then - the end of > amateur radio is nigh. My one regret is that me and my UV5R have > contributed to that because I did not return it for a refund. > > (The UV5R is not a particularly good radio anyway. The colour display uses > far too much power and cannot cope with bright sunlight. Mono displays are > generally far better in both respects, and who really needs colour?) > > 73, Chris, an Amateur Radio operator since 1973. > > > ________________________________ >

8 11

[chirp_users] iso usb problems
by Phil 22 Mar '18

22 Mar '18

Hi All I'm facing repeated problems creating a chirp usb system. I've checked my download is correct. Burning is another story. Has anyone burned the iso recently? I've been using Debian, but just now switched to latest Mint. I have tried unetbootin, "Disks", and various other tools. I get messages saying this is not a bootable disk. How can I seriously validate the steps and accuracy of my burning process? Hopefully yours Phil VK4AJK

5 4

[chirp_users] Chirp wont launch in MacOS
by Neil Harrington 22 Mar '18

22 Mar '18

I followed all the directions (including downloading a new python package) and the search does not provide a remedy. Adding in the log file Appreciate the help. Neils-MacBook-Air:~ neilharrington$ /Users/neilharrington/Downloads/chirp-daily-20180316-8.app/Contents/MacOS/chirp ; exit; WARNING: Icon not found Traceback (most recent call last): File "/Users/neilharrington/Downloads/chirp-daily-20180316-8.app/Contents/MacOS/../Resources/chirp/chirpw", line 126, in <module> a = mainapp.ChirpMain() File "/Users/neilharrington/Downloads/chirp-daily-20180316-8.app/Contents/Resources/chirp/chirp/ui/mainapp.py", line 2019, in __init__ self._init_macos(mbar) File "/Users/neilharrington/Downloads/chirp-daily-20180316-8.app/Contents/Resources/chirp/chirp/ui/mainapp.py", line 1961, in _init_macos LOG.error("No MacOS support: %s" % e) NameError: global name 'e' is not defined logout Saving session... ...copying shared history... ...saving history...truncating history files... ...completed. -- Neil D. Harrington 650.353.3722 linkedin.com/in/neildharrington

2 2

[chirp_users] This just kills me....
by P² P² 22 Mar '18

22 Mar '18

The problem with programming the radios has nothing to do with the radios or the software. It is because of WAR!!! If you look at the start end of your radio programming CABLE, you will see a bulbous end which contains a small USB-TTL converter. The Manufacturers of those “chips” also wrote software to handle the conversion process. Along comes ANOTHER Chinese Manufacturer who reverse engineers the chips (without paying for R+D) and puts them out for even cheaper. The original chip maker then puts out software that will identify the fake chips and fail to operate, thus creating the problems for hams. Even the radio manufacturers have jumped on the cheap bandwagon and incorporated the fake chips in their own cables. So, WAR has broken out, back and forth. (I converted most of mine to FTDI chips as they have the fewest driver issues.) There is a trend in even more recent radio makers to provide a straight thru cable with NO USB-TTL chip in the cable. All that is done in the radio and the makers have full control over that in their OWN software. So far I have seen this in the Radioddity’s GD-77 and RD-5R. Unfortunately, (HINT, HINT, HINT) CHIRP won’t work with these DMR radios (YET???!!!) So, the moral of this story is WAR is BAD! (Or CHIRP, please rid me of the quirks of Chinese software.) NH6BF Sent from Mail for Windows 10

1 0

[chirp_users] This just kills me
by Dennis Wage 21 Mar '18

21 Mar '18

This: https://www.amazon.com/2-Channel-Remote-Control-Transmitter-Highest/dp/B078… costs $15 more than a UV-5R Give me a break. Dennis M. Wage 245 Corum Hill Road Castalian Springs, TN 37031 (615) 310-4242 Cell (615) 562-5128 Home http://hammondb3organ.net http://overdubs.net

4 4

[chirp_users] OT headphone output
by Dennis Wage 20 Mar '18

20 Mar '18

Hello, If this is too off topic, scold me and I'll never do it again. I have a UV-5R. I love this $25 radio for what it is, except. I want to use headphones. However I cannot stand to have audio in just one ear. Plus I drive noisy lawn gear and tractors. I use ear buds with gun muffs over the ear. Microphone will come later when I get my technician test passed. The head phone output is 2.5mm TRS (this alone bugs the crap out of me.) In addition, the tip only carries audio and the ring is TX data. When the radio is scanning there is a low frequency thump in time with the scan that comes out the data port ring. If I plug a 2.5mm TS the data port ring will short to the sleeve. I'm not sure this is good idea. So, I think my only option is to buy a 2.5mm TRS and make a mono cord that only uses the tip. I can then split it to a stereo TRS 3.5mm female to plug my earbuds into. Any other ideas would be appreciated. Dennis M. Wage 245 Corum Hill Road Castalian Springs, TN 37031 (615) 310-4242 Cell (615) 562-5128 Home http://hammondb3organ.net http://overdubs.net

3 3

[chirp_users] Programming TYT TH 9000
by Allen Stines 19 Mar '18

19 Mar '18

I have a TH 9000 that I am trying to program with CHIRP. According to software, the radio 9000_144 is supported by Chrip, however, when I try to read from radio, it says, "unsupported model." Any ideas? I have used Chirp in the past to program this radio using Windows 7, which is what I am using now. Allen Stines, aka 00 KF4ZDS Assistant Chief, Big Pine VFD (Cell) 828-712-6554 <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_cam…> Virus-free. www.avg.com <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_cam…> <#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>

3 5

[chirp_users] TH-9800
by P² P² 19 Mar '18

19 Mar '18

I have a TH-9800 that I have programmed with CHIRP for years…never had a problem. The cable that is used looks like a standard USB to mini USB cable. It is NOT. It has a USB to TTL converter inside it… Sent from Mail for Windows 10

1 0

[chirp_users] New Daily Build
by Build System 16 Mar '18

16 Mar '18

Greetings, A new daily build of CHIRP is available. This includes changes made directly to the tree yesterday, and may include additional features, bug fixes, and/or bugs. If you are interested in trying it, grab it from the following location: http://trac.chirp.danplanet.com/chirp_daily/daily-20180316 A list of the changes included in this build (since the last daily) follows: Changes for Build #519 [Nicolas Pike <nicolas.jon.pike(a)gmail.com>] [FT-70] New Model #5329 Always Save/Display as memory name (For the moment..) [Dan Smith <dsmith(a)danplanet.com>] Fix tox unit test requirement for mox library #0

1 0

[chirp_users] New Daily Build
by Build System 14 Mar '18

14 Mar '18

Greetings, A new daily build of CHIRP is available. This includes changes made directly to the tree yesterday, and may include additional features, bug fixes, and/or bugs. If you are interested in trying it, grab it from the following location: http://trac.chirp.danplanet.com/chirp_daily/daily-20180314 A list of the changes included in this build (since the last daily) follows: Changes for Build #518 [Mathias Weyland <lt-betrieb(a)hb9uf.ch>] [Alinco DJ-G7] Code cleanup to pass linter tests Related to #5275

2 1

Re: [chirp_users] OT, BTECH UV-50X3
by Rich Messeder 10 Mar '18

10 Mar '18

Sorry...skimmed this as 5x3, not 50x3...but I saw a post last year that complained that there is no voice mode. ~R~ On 2018-03-10 11:44:+0000, Rich Messeder wrote: >My 5x3s speak the menu. > >73 de ~Rich~ NE1EE ARES AEC >Short email? No html? Here's why: http://emailcharter.org/ > >On 2018-03-09 20:22:-0800, Darby Collier wrote: > >>The 50X2 does not, beeps only - likely the same for that one. >> >>On Mar 9, 2018 20:18, "Glenn At Home" <<mailto:GlennErvin@cableone.net>GlennErvin(a)cableone.net> wrote: >>Hi All, >>Does anyone know if this radio speaks the menus like the Baofeng HT units do? >>You might reply off-list on this since it's not really Chirp related. >>Thanks. > >_______________________________________________ >chirp_users mailing list >chirp_users(a)intrepid.danplanet.com >http://intrepid.danplanet.com/mailman/listinfo/chirp_users >This message was sent to Rich NE1EE at ne1ee(a)hotmail.com >To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com 73 de ~Rich~ NE1EE ARES AEC Short email? No html? Here's why: http://emailcharter.org/

1 0

Re: [chirp_users] OT, BTECH UV-50X3
by Rich Messeder 10 Mar '18

10 Mar '18

My 5x3s speak the menu. 73 de ~Rich~ NE1EE ARES AEC Short email? No html? Here's why: http://emailcharter.org/ On 2018-03-09 20:22:-0800, Darby Collier wrote: >The 50X2 does not, beeps only - likely the same for that one. > >On Mar 9, 2018 20:18, "Glenn At Home" <<mailto:GlennErvin@cableone.net>GlennErvin(a)cableone.net> wrote: >Hi All, >Does anyone know if this radio speaks the menus like the Baofeng HT units do? >You might reply off-list on this since it's not really Chirp related. >Thanks.

1 0

[chirp_users] OT, BTECH UV-50X3
by Glenn At Home 09 Mar '18

09 Mar '18

Hi All, Does anyone know if this radio speaks the menus like the Baofeng HT units do? You might reply off-list on this since it's not really Chirp related. Thanks.

2 1

[chirp_users] New Radio / Use
by Gene Vincent 09 Mar '18

09 Mar '18

Just got a new BTECH 5x3. It is my understanding that there is no other software available except CHIRP. Is there anyway to adjust radio menu items with CHIRP? Listing a few as examples: TX-RX display color, channel display mode (CH#,Freq,Name), I don't see any way to set DTMF alerts, which is the main reason I bought this radio. Thanks in advance.

4 4

[chirp_users] Global Skip/Other Fields with Menues
by Gene Vincent 09 Mar '18

09 Mar '18

I accidentally got the "skIp" field to change all channels entered so far to skip. I don't know how I managed that. I also managed to get them all changed back. With my laptop, not realizing which key combination I hit. Can someone please tell me how to make the channels all skip or all narrow band, etc. using just that column? Thanks.

2 1

[chirp_users] Yaesu ft2900
by RolyT 09 Mar '18

09 Mar '18

I was recommended to put an old driver 3.2 into my PC windows 7 pro for the patch lead.. It took some getting in but I still get the same message error cant find header. any more ideas would be great otherwise why list the radio on chirp ? Cheers Roly T G0UKS --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus

2 2

[chirp_users] New Daily Build
by Build System 09 Mar '18

09 Mar '18

Greetings, A new daily build of CHIRP is available. This includes changes made directly to the tree yesterday, and may include additional features, bug fixes, and/or bugs. If you are interested in trying it, grab it from the following location: http://trac.chirp.danplanet.com/chirp_daily/daily-20180309 A list of the changes included in this build (since the last daily) follows: Changes for Build #516 [nicolas jon pike <nicolas.jon.pike(a)gmail.com>] New Model #5329 FT70 Driver I now have enough of the driver working to be useful. Read / write memories, a number of the settings, and import from RepeaterBook work. Saving modes dn,vw and AMS in memory channels, do not currently work. Banks have not been tested - may now work, VFO settings not implemented (etc) I have also raised a request for C4FM to be added to CHIRP Modes. [Mathias Weyland <lt-betrieb(a)hb9uf.ch>] [Alinco DJ-G7] Introduce empty flag, mode & frequency range checks. At the time I was adding support for the DJ-G7 radio, I was not aware of a flag that was used to hide memory channels in the main band. The main band only supports a subset of modes and frequencies on this radio. My original code used this flag improperly, such that a channel was never hidden from the main band regardless of its settings. This does not do any harm to the radio, but such a memory channel is useless in the main band due to hardware constraints. More importantly, the original programming software by Alinco crashes when operating on a memory map pulled from a radio programmed with chirp if the flag is not used correctly. After some discussions with and advice from Emiel, I have completed a patch that adds proper support for this flag. The patch is attached. See #5275 for a more in-depth discussion of the issue.

1 0

[chirp_users] Memory channel
by Kevin 08 Mar '18

08 Mar '18

I have a Yeasu FT-857d, I was able to load all the repeaters I wanted in from importing from repeaterbook, My questions is, is there a easy way to rename the channels to the frequency instead of the repeater call sign?Thanks in advance.Kevin KI7MOC

2 1

Re: [chirp_users] MAC & Yaesu FT2d? (Michael Sanford)
by Kell Bodholt 08 Mar '18

08 Mar '18

I'm a recent Chirp (mac version) user that is running macOS and a FT-2DR. As stated by others, get the RT Systems usb cable and download the RT Systems macOS drivers from the RT Systems website, together with the instructions. I did this and my MacBook Air recognizes the usb driver and I'm able to use Chirp in the macOS environment (not in a parallel environment). RT Systems USB-68 programming cable for the FT-2DR: https://www.rtsystemsinc.com/USB-68-Programming-Cable-p/usb-68.htm RT Systems USB-68 macOS drivers: https://www.rtsystemsinc.com/kb_results.asp?ID=9 Hope this helps. Kell -----Original Message----- From: <chirp_users-bounces(a)intrepid.danplanet.com> on behalf of <chirp_users-request(a)intrepid.danplanet.com> Reply-To: <chirp_users(a)intrepid.danplanet.com> Date: Thursday, March 8, 2018 at 12:02 PM To: <chirp_users(a)intrepid.danplanet.com> Subject: chirp_users Digest, Vol 111, Issue 4 MAC & Yaesu FT2d? (Michael Sanford)

1 0

[chirp_users] More info to solve the Macbook 10.9.5/Yaesu ft2900 MARS expanded/valley enterprises cable "no joy"
by Peter Ryan 07 Mar '18

07 Mar '18

D.J. Ring has been very helpful in his ongoing patient advice on this issue, and asked me to outline the drivers on my 10.9.5 Macbook. I have zero background in computers and such, and so much of the advice from others goes right over my head, and I am sure many others. Here is the list of drivers on my Mac with the Valley Ent. cable plugged in. USB Hi-Speed Bus Apple USB-EHCI OxO aa9and an aa6, and an OxO5ac, and an OxO aa7 FT232R vender ID: FTDIlocation: OxO620000000 / 3 BRCM2046 HubOxOa5c (Broadcom)location: OxO610000000 / 2 then some other Apple related "keyboard" and "IR Receiver" related stuff. NOTHING ELSE!Does that mean I have all that I need in order to program my Yaesu 2900R on CHIRP or not?

2 1

[chirp_users] Has ANYONE actually succeeded in programming a Yaesu FT2900 on CHIRP?
by Peter Ryan 07 Mar '18

07 Mar '18

If there is anyone who has actually SUCCEEDED in programming the FT2900R on CHIRP with a Macbook (10.5.5 Maverick here), would you please offer a reply here? My query last week received no responses. And I am reading mixed messages and member's thoughts and opinions on the subject in yesterday's other member's parallel question, but we have not seen anything from anyone who has actually succeeded with a Mac and a Valley Enterprises cable. I suspect there are several here who would profit from a "step-by-step" tutorial from a member who has. It is listed as a programmable radio on Chirp, but at this point, I am starting to wonder why. Thanks in advance for your help on this. :)

3 2

[chirp_users] Baofeng UV-6 "refused to send second block 0x1ec0"
by Charley Bratton 07 Mar '18

07 Mar '18

While attempting to run the initial download for a group of new recently received Baofeng UV-6 radios, all are responding with “radio refused to send second block 0x1ec0” right at the tail end of the download... I’m using the most recent CHIRP build for Mac. I’ve attempted multiple Macs, no difference. I’ve attempted older 2017 versions of CHIRP, no difference. The cable I’m using works for other Baofengs, including UV-6 units we purchased 5 months ago, just not these particular UV-6 units. These units are clearly labeled UV-6 (not UV-6R). Tried the UV-6R setting just in case, but the download didn’t start. Any suggestions? -Charley KE4QBW

1 1

[chirp_users] MAC & Yaesu FT2d?
by J 07 Mar '18

07 Mar '18

Running CHIRP on a MacBook Pro running 10.7.?. I can access my FT60R but the FT2D is throwing an error code about the USB port not being installed? Any help would be greatly appreciated. John KY4BSL

2 3

[chirp_users] Yaesu ft2900 no connection
by RolyT 07 Mar '18

07 Mar '18

Why doe’s Chirp have the Yaesu FT2900 listed as one that can be programmed. I purchased a lead with disc, the disc has programs for other radios but the one for Yaesu is in Chinese so hoped that Chirp would do the job. It fails with the error—cannot find header and since then after searching around at least 2 years ago people were having problems but looking through them no one seems to have an answer. Am I doing something wrong, I have a Boafeng and that works fine. --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus

3 2

[chirp_users] Thanks to the group
by Brandon Clark 04 Mar '18

04 Mar '18

Thanks to the Chirp developers for supporting this project. There was a bit of a learning curve for me, but I finally got three of my radios programmed using Chirp. (I had been using RT Systems before but switched to Chirp when I switched my systems to Linux.) I recently moved to Alaska so I've had to not just rearrange channels, but do a complete reprogram of all repeaters, nodes, and simplex frequencies. To any other fellow Chirp-newbies out there this was the process I used: 1. Find cables that worked with my radios (the RT Systems ones wouldn't), 2. Download what was already programmed in my radios, 3. Export to a CSV file so I would have the formatting right, 4. Work with the new channels I wanted in LibreOffice: 1. Change the layout of my spreadsheets from the way RTSys was arranged to the way Chirp is laid out, 5. Paste values into the CSV exports, 6. Import into Chirp, 7. Upload into the radios, I still have an Icom Ht that I'm having communication issues with (no pun intended), but once I get that worked out I should be in business. Anyway, thanks to the developers for making an open source and cross platform programming option. 73, Brandon Clark, KL7BSC

2 1

[chirp_users] CSV file.
by Dennis Wage 02 Mar '18

02 Mar '18

The answer to my question is pretty apparent, but I want to double check. In the CSV file I'm assuming that some, most or all of the numeric columns cannot be blank or set to zero. Example: Changing tone mode to (None) in Chirp is blank in csv. However if I change rToneFreq, cToneFreq which are now unused to 0 or blank I get an error when importing. So when tone mode is set to none rToneFreq cToneFreq are simply ignored? Dennis M. Wage 245 Corum Hill Road Castalian Springs, TN 37031 (615) 310-4242 Cell (615) 562-5128 Home http://hammondb3organ.net http://overdubs.net

3 4

[chirp_users] Problems connecting Yaesu FT-2900r
by Peter Ryan 01 Mar '18

01 Mar '18

Hi Guys: I just received my Valley Enterprise Yaesu FT-2900R cable (RPC-YM6-UF). Upon trying to connect CHIRP on my MACBOOK 10.9.5 Maverick XOS, and the MARS-modified 2900R radio, I get an error message of: "Could not open port (error #2)...no such file or directory."I am successful with connecting my Yaesu FT-60 to the Mac, and I did not make any changes to the computer before attempting to hook up the FT-2900R, but with the FT-2900 cable plugged in, I do get an new extra choice in my drop down menu "RADIO: Download from radio" "serial" box choices. The FT-60 works using the original "/DEV/cu.usbserial", but the FT-2900R fails to work with either that older choice, or the new choice of "/DEV/cu.usbserial-A107368". I have gone to the various CHIRP help forums, and there is a lot about using a build made before some date before circa 06/2016 for a MARS "modded" radio, but that seems to relate only to a PC using Windows. The MacBook info didn't seem to relate to a need for an earlier "build". Indeed, I couldn't find any new builds for a MAC since 2016. What am I doing wrong? Thanks for your help in advance.MacBook 10.9.5Yaesu Ft-2900R mobile radio Valley Ent. FT-1900/2900 FTDI cable

1 0

Re: [chirp_users] Skip Channels Scan Baofeng UV-5R (HN5RV01) (1FB297)
by Darby Collier 27 Feb '18

27 Feb '18

Yes. On Feb 27, 2018 07:01, "Dennis Wage" <dwage(a)dwage.com> wrote: Should skip (S) work on this radio? Dennis M. Wage 245 Corum Hill Road Castalian Springs, TN 37031 (615) 310-4242 Cell (615) 562-5128 Home http://hammondb3organ.net http://overdubs.net _______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to DarbyInGreen at collier.darby(a)gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@ intrepid.danplanet.com

5 5

[chirp_users] Unable to Connect
by Richard Gaun 27 Feb '18

27 Feb '18

For the first time in many years I'm unable to read or program my UV-82. I keep getting a "com" error When trying to download. Just yesterday I successfully use the software to program several other radios. Help!!! Thanks. Rich +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Richard P Gaun, III P.O. Box 382 Youngtown, Arizona 85363 Cell & Text 480-273-3755 The information contained within the referenced, linked, or directed email communication is intended to be a confidential communication between the original sender and recipient(s), and is to be treated as confidential. Any and all works, ideas, or copy within are not to be used in any manner other by which they were intended. If you believe you have received this or any other email in error, please contact me at the above email. ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

3 2

[chirp_users] Skip Channels Scan Baofeng UV-5R (HN5RV01) (1FB297)
by Dennis Wage 27 Feb '18

27 Feb '18

Should skip (S) work on this radio? Dennis M. Wage 245 Corum Hill Road Castalian Springs, TN 37031 (615) 310-4242 Cell (615) 562-5128 Home http://hammondb3organ.net http://overdubs.net

1 0

Re: [chirp_users] chirp_users Digest, Vol 110, Issue 17
by C.S. Arthur 23 Feb '18

23 Feb '18

to Scott Brady: my cheap junk programming cable that refused to work had an ‘official’ looking Baofeng label on it. the 12 dollar special i bought from BaoTech or one of those real Baofeng vendors works flawlessly. dont be misled by labels (Baofeng UV-5TPS) C.S. Arthur csarthur(a)gmail.com KE7EFS > > Message: 7 > Date: Thu, 22 Feb 2018 17:45:04 -0700 > From: Scott Brady <utahkarate(a)gmail.com> > Subject: [chirp_users] Trouble with iOS 10.13.3 > To: chirp_users(a)intrepid.danplanet.com > Message-ID: > <CAHpcEUh0PUFAbL+tYRavs8kYPZvZJHi35+AbCFdv4G+2t92Qtw(a)mail.gmail.com> > Content-Type: text/plain; charset="utf-8" > > Hello, > > I have been trying in vain to get my radio to talk with CHIRP on my Macbook > Pro running 10.13.3. I have downloaded and installed the latest cable > drivers and the latest CHIRP build. I have verified that the cable is > recognized, but when I try to download from the radio, even with the > correct radio (UV-5RV2+) and port (/dev/cu.usbserial), it simply hangs and > says that the radio did not respond. All of the software works great on my > PC, but I have been trying to get the Mac version to work for a long time > with no luck. I have scanned countless forums and mail lists, but I have > yet to find a solution. The cable I have is a Baofeng cable (it says > Baofeng right on it), so I assume that this is not a cheap junk cable. I > have attached the debug log below. Can anyone help please!! >

1 0

[chirp_users] Trouble with iOS 10.13.3
by Scott Brady 23 Feb '18

23 Feb '18

Hello, I have been trying in vain to get my radio to talk with CHIRP on my Macbook Pro running 10.13.3. I have downloaded and installed the latest cable drivers and the latest CHIRP build. I have verified that the cable is recognized, but when I try to download from the radio, even with the correct radio (UV-5RV2+) and port (/dev/cu.usbserial), it simply hangs and says that the radio did not respond. All of the software works great on my PC, but I have been trying to get the Mac version to work for a long time with no luck. I have scanned countless forums and mail lists, but I have yet to find a solution. The cable I have is a Baofeng cable (it says Baofeng right on it), so I assume that this is not a cheap junk cable. I have attached the debug log below. Can anyone help please!!

2 4

[chirp_users] Alinco Cable Experience?
by Brandon Clark 22 Feb '18

22 Feb '18

Hello group, I'm probably going to be purchasing an Alinco DJ-G7 soon, and I was wondering if the Alinco brand cable (part # ERW-7) works with Chirp? Has anyone used it before? The instructions for it indicate that it uses an FTDI driver, so I would think it has a genuine FTDI chip in it. 73, Brandon

2 1

[chirp_users] CHIRP w a Motorola CDM750
by George Tucker 22 Feb '18

22 Feb '18

Does anyone have any experience using CHIRP with a Motorola CDM750 or any of its generation of radios? GeorgeW6HAF

3 2