August 2015 - Users - lists.chirpmyradio.com

[chirp_users] Programming IC-W32A
by Delbert Schmidt 20 Aug '15

20 Aug '15

I'm unable to find the correct page to start programming my HT. Can you HELP? Thanks........Del

2 1

[chirp_users] Fw: important
by clarket＠iol.ie 20 Aug '15

20 Aug '15

Hello! Important message, visit http://theunbreakableproject.com/considered.php?e clarket(a)iol.ie

2 1

[chirp_users] Chirp not communicating
by Verne Brown 19 Aug '15

19 Aug '15

Using Macbook Pro with OS 10.10.5 (Yosemite)Chirp 0.4.1Radio - Baofeng UV-5R I've been successful using older mac os' in communicating to this radio in the past I try to download the radio's program i get this error message "An error had occurredcould not open port /dev/cu.vernebrownscomputer-Blu:[Ermo 16]resource busy : '/dev/cu.vernebrownscomputer-Blu' Not sure what I'm doing wrong or forgot to do. did the cable check - it recognizes the type of chip in the cable as the debug instructions.

2 1

[chirp_users] Can I use chirp for icom radios
by Philip Mobile 19 Aug '15

19 Aug '15

Can I use chirp to program my icom 2720 or icom 2820? Thank you for your time, Philip Canterbury Sent from my iPhone

3 3

[chirp_users] repeater programming on UV5R
by Martin Goodrum 19 Aug '15

19 Aug '15

I am having a problem programming a couple of my local 70cm repeaters into my baofang UV5R. The problem is that I can access the repeater but although the repeater responds, as indicated by the green light being lit, I hear no audio. This is because R-CTCss is set to on. These two repeaters do not transmit a CTCss tone so I need to program R-CTCSS off on the radio but so far I have been unsuccessful in doing this! Manually loading the repeater into the radio it all works fine, just using a memory channel programmed with Chirp. It is just two repeaters that give probs. all others are OK. So question is how do I program the R-CTCss off for these two memory channels, but leave T-CTCss active of course. Martin G3ZQU.

2 1

[chirp_users] Loading to a Windows 10 Platform
by Tim Hass 18 Aug '15

18 Aug '15

Has anyone been successful in loading the latest daily build onto a Windows 10 Platform? My efforts have not met with any success. Tim Hass kd8zyw

3 5

[chirp_users] Yaesu FT-1500M
by Mike Ligeza 16 Aug '15

16 Aug '15

Is there any up-date on the progress to add the Yaesu FT-1500M to the list of rigs that CHIRP will work with? -- ............................................... Mike Ligeza - VE3UIL Smiths Falls, ON mike.ligeza(a)gmail.com

1 0

[chirp_users] UV-82 with new firmware.
by Steve Houts 16 Aug '15

16 Aug '15

Have received 3 UV-82 with firmware version N822411N822411. Downloaded from radio the programming template. Entered tones freqs and other info try to up load to radios the new img. image and it says radio model not detected, then I manually enter that it’s a UV-82 and still try to upload to radio and as soon as I do it says firmware not supported. I’ve loaded daily build from yesterday have done a recovery which I think is not need for the 82 and still no luck. Even went so far as to reload the driver program. Not sure what this has done now. I see Pofung is now Baofeng again on units I received. Any help appreciated.

3 2

[chirp_users] bf-9500
by mark worley 15 Aug '15

15 Aug '15

Newbi here, does anyone know if there will be support for the pofung BF9500 Thanks

2 1

[chirp_users] Baofeng UV-5R
by Charles Albert 15 Aug '15

15 Aug '15

Hello, All... I have the above radio and I'm trying to get CHIRP 0.3.1 on Linux to connect to the radio. I'm using an USB cable that shows up as ttyUSB0. None of the lights on the radio change (LED should blink, right?) and CHIRP errors that the radio is not responding. Any ideas where I should start looking? Take Care & 73 Charles KC6UFM

7 13