[chirp_users] Chirp and BaoFeng UV 5R not communicating
On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP.
On Friday all I got was the following message: Radio Did Not Respond.
I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP.
Any suggestions?
Thanks Chuck KJ7INT
On Sat, Aug 22, 2020 at 6:46 PM Charles Gierke cgierke@cox.net wrote:
On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP.
On Friday all I got was the following message: Radio Did Not Respond.
I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP.
Any suggestions?
Thanks Chuck KJ7INT
Hi Chuck,
You will get the exact same error message if you don't plug the 2-pin plug into the radio. So make sure that the 2-pin plug is fully inserted into the socket of the radio. Some have had to put a little pressure on the plug during the cloning process.
Jim KC9HI
Thanks for the suggestion, I cleaned the prongs with alcohol I'll clean the base and try again.
On August 22, 2020 at 3:50 PM Jim Unroe < rock.unroe@gmail.com mailto:rock.unroe@gmail.com > wrote:
On Sat, Aug 22, 2020 at 6:46 PM Charles Gierke < cgierke@cox.net mailto:cgierke@cox.net > wrote: > > > On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP.>> > On Friday all I got was the following message: Radio Did Not Respond.>> > I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP.> >> > Any suggestions?>> > Thanks Chuck KJ7INT> Hi Chuck,You will get the exact same error message if you don't plug the 2-pin plug into the radio. So make sure that the 2-pin plug is fully inserted into the socket of the radio. Some have had to put a little pressure on the plug during the cloning process. Jim KC9HI _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net mailto:cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com
no luck yet. I tried pressure straight into the radio, to the back side of the radio, to the front side of the radio, to the top of the radio and to the bottom of the radio. similar results, the LCD screen blinks and goes back to the beginning screen.
thanks again for the suggestion
On August 22, 2020 at 3:50 PM Jim Unroe < rock.unroe@gmail.com mailto:rock.unroe@gmail.com > wrote:
On Sat, Aug 22, 2020 at 6:46 PM Charles Gierke < cgierke@cox.net mailto:cgierke@cox.net > wrote: > > > On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP.>> > On Friday all I got was the following message: Radio Did Not Respond.>> > I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP.> >> > Any suggestions?>> > Thanks Chuck KJ7INT> Hi Chuck,You will get the exact same error message if you don't plug the 2-pin plug into the radio. So make sure that the 2-pin plug is fully inserted into the socket of the radio. Some have had to put a little pressure on the plug during the cloning process. Jim KC9HI _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net mailto:cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com
Try making sure you vigorously plug the connector into the radio and hold it in while loading from chirp. Also turn the volume up from minimum. Last resort run chirp as adminstrator.
On Sat, Aug 22, 2020, 3:45 PM Charles Gierke cgierke@cox.net wrote:
On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP.
On Friday all I got was the following message: Radio Did Not Respond.
I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP.
Any suggestions?
Thanks Chuck KJ7INT _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Silver Fox at alan.r.hill@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Thanks for the suggestions, I will apply constant pressure. I never tried starting a program as administrator, it is worth a try.
On August 22, 2020 at 4:11 PM Alan Hill alan.r.hill@gmail.com wrote:
Try making sure you vigorously plug the connector into the radio and hold it in while loading from chirp. Also turn the volume up from minimum. Last resort run chirp as adminstrator. On Sat, Aug 22, 2020, 3:45 PM Charles Gierke < cgierke@cox.net mailto:cgierke@cox.net > wrote: > >On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP. On Friday all I got was the following message: Radio Did Not Respond. I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP. Any suggestions? Thanks Chuck KJ7INT _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Silver Fox at alan.r.hill@gmail.com mailto:alan.r.hill@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com > _______________________________________________chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Charles, I have never gotten my radios to sync either and Finely gave up. I even bought 2 cables thinking it was a cable I followed all the instructions just like you. If you succeed, please email me back
Gary A Cox Sent from my iPhone
On Aug 22, 2020, at 4:12 PM, Alan Hill alan.r.hill@gmail.com wrote:
Try making sure you vigorously plug the connector into the radio and hold it in while loading from chirp. Also turn the volume up from minimum. Last resort run chirp as adminstrator.
On Sat, Aug 22, 2020, 3:45 PM Charles Gierke cgierke@cox.net wrote: On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP.
On Friday all I got was the following message: Radio Did Not Respond.
I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP.
Any suggestions?
Thanks Chuck KJ7INT
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Silver Fox at alan.r.hill@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Gary at garyacox@sbcglobal.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Did you check Windows Device Manager to see if your cable shows to be a Prolific cable? If it is, try rolling your driver back to 3.2.0.0. Check www.miklor.com for info. Check under Drivers.
Jardy Dawson WA7JRD
Message sent by....Oh look!! Pretty lights!!
On Aug 23, 2020, at 08:24, Gary A. Cox garyacox@sbcglobal.net wrote:
Charles, I have never gotten my radios to sync either and Finely gave up. I even bought 2 cables thinking it was a cable I followed all the instructions just like you. If you succeed, please email me back
Gary A Cox Sent from my iPhone
On Aug 22, 2020, at 4:12 PM, Alan Hill alan.r.hill@gmail.com wrote:
Try making sure you vigorously plug the connector into the radio and hold it in while loading from chirp. Also turn the volume up from minimum. Last resort run chirp as adminstrator.
On Sat, Aug 22, 2020, 3:45 PM Charles Gierke cgierke@cox.net wrote: On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP.
On Friday all I got was the following message: Radio Did Not Respond.
I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP.
Any suggestions?
Thanks Chuck KJ7INT
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Silver Fox at alan.r.hill@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Gary at garyacox@sbcglobal.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Jardy at jardy72@yahoo.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
The cable has been working since August 2019. for over a year no problems. perhaps the warranty is up lol
On August 23, 2020 at 8:34 AM Jardy via chirp_users chirp_users@intrepid.danplanet.com wrote:
Did you check Windows Device Manager to see if your cable shows to be a Prolific cable? If it is, try rolling your driver back to 3.2.0.0. Check www.miklor.com for info. Check under Drivers. Jardy Dawson WA7JRD Message sent by....Oh look!! Pretty lights!! > > On Aug 23, 2020, at 08:24, Gary A. Cox <garyacox@sbcglobal.net> wrote:>> > Charles,I have never gotten my radios to sync either and Finely gave up. I even bought 2 cables thinking it was a cable I followed all the instructions just like you. If you succeed, please email me back Gary A Cox Sent from my iPhone > > > On Aug 22, 2020, at 4:12 PM, Alan Hill <alan.r.hill@gmail.com> wrote:> >> > > Try making sure you vigorously plug the connector into the radio and hold it in while loading from chirp. Also turn the volume up from minimum. Last resort run chirp as adminstrator. On Sat, Aug 22, 2020, 3:45 PM Charles Gierke < cgierke@cox.net mailto:cgierke@cox.net > wrote: > > > >On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP. On Friday all I got was the following message: Radio Did Not Respond. I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP. Any suggestions? Thanks Chuck KJ7INT _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Silver Fox at alan.r.hill@gmail.com mailto:alan.r.hill@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com > > > _______________________________________________chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Gary at garyacox@sbcglobal.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com > > _______________________________________________chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Jardy at jardy72@yahoo.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com >
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
If Windows does an update, it might change tho the ‘latest and greatest’ version of the driver. If the cable has a fake Prolific chip in it, that driver is designed to make the fake chip not work, so you have to roll it back to 3.2.0.0. The driver will also be updated if you plug the cable in a different USB port.
Sent from Yahoo Mail for iPhone
On Sunday, August 23, 2020, 11:32, Charles Gierke cgierke@cox.net wrote:
The cable has been working since August 2019. for over a year no problems. perhaps the warranty is up lol
On August 23, 2020 at 8:34 AM Jardy via chirp_users chirp_users@intrepid.danplanet.com wrote:
Did you check Windows Device Manager to see if your cable shows to be a Prolific cable? If it is, try rolling your driver back to 3.2.0.0. Check www.miklor.com for info. Check under Drivers.
Jardy Dawson WA7JRD Message sent by....Oh look!! Pretty lights!!
On Aug 23, 2020, at 08:24, Gary A. Cox garyacox@sbcglobal.net wrote:
Charles, I have never gotten my radios to sync either and Finely gave up. I even bought 2 cables thinking it was a cable I followed all the instructions just like you. If you succeed, please email me back
Gary A Cox Sent from my iPhone
On Aug 22, 2020, at 4:12 PM, Alan Hill alan.r.hill@gmail.com wrote:
Try making sure you vigorously plug the connector into the radio and hold it in while loading from chirp. Also turn the volume up from minimum. Last resort run chirp as adminstrator.
On Sat, Aug 22, 2020, 3:45 PM Charles Gierke < cgierke@cox.net> wrote:
On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP.
On Friday all I got was the following message: Radio Did Not Respond.
I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP.
Any suggestions?
Thanks Chuck KJ7INT _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Silver Fox at alan.r.hill@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Gary at garyacox@sbcglobal.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Jardy at jardy72@yahoo.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Jardy at jardy72@yahoo.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
I have the cable needed to be held into the radio really hard for it to work.
Sent from my iPad
On Aug 23, 2020, at 12:32 PM, Charles Gierke cgierke@cox.net wrote:
The cable has been working since August 2019. for over a year no problems. perhaps the warranty is up lol
On August 23, 2020 at 8:34 AM Jardy via chirp_users chirp_users@intrepid.danplanet.com wrote:
Did you check Windows Device Manager to see if your cable shows to be a Prolific cable? If it is, try rolling your driver back to 3.2.0.0. Check www.miklor.com for info. Check under Drivers.
Jardy Dawson WA7JRD
Message sent by....Oh look!! Pretty lights!!
On Aug 23, 2020, at 08:24, Gary A. Cox garyacox@sbcglobal.net wrote:
Charles, I have never gotten my radios to sync either and Finely gave up. I even bought 2 cables thinking it was a cable I followed all the instructions just like you. If you succeed, please email me back
Gary A Cox Sent from my iPhone
On Aug 22, 2020, at 4:12 PM, Alan Hill alan.r.hill@gmail.com wrote:
Try making sure you vigorously plug the connector into the radio and hold it in while loading from chirp. Also turn the volume up from minimum. Last resort run chirp as adminstrator.
On Sat, Aug 22, 2020, 3:45 PM Charles Gierke < cgierke@cox.net> wrote:
On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP.
On Friday all I got was the following message: Radio Did Not Respond.
I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP.
Any suggestions?
Thanks Chuck KJ7INT
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Silver Fox at alan.r.hill@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Gary at garyacox@sbcglobal.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Jardy at jardy72@yahoo.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Brian at brian@dashley.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
NO luck yet. I held the plug in as far as it would go, no change. I turned the volume up all the way, no luck. I closed CHIRP and re-opened as Administrator,still no luck up or downloading.
thanks for your assistance
On August 22, 2020 at 4:11 PM Alan Hill alan.r.hill@gmail.com wrote:
Try making sure you vigorously plug the connector into the radio and hold it in while loading from chirp. Also turn the volume up from minimum. Last resort run chirp as adminstrator. On Sat, Aug 22, 2020, 3:45 PM Charles Gierke < cgierke@cox.net mailto:cgierke@cox.net > wrote: > >On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP. On Friday all I got was the following message: Radio Did Not Respond. I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP. Any suggestions? Thanks Chuck KJ7INT _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Silver Fox at alan.r.hill@gmail.com mailto:alan.r.hill@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com > _______________________________________________chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Tried beveling the edges, no change. Thanks
On August 23, 2020 at 3:08 PM Don Goodrich don.goodrich@cheerful.com wrote:
1st the volume level has no effect on data transfer... Sometimes a little plastic shaving is needed. Shave carefuly a little off the plastic shroud around the cable male connector where it plugs into the radio as it interferes with the radio's case prventing the connector from solidly seating. This may be the issue here... Don Goodrich don.goodrich@Cheerful.com AF7DG Sent: Sunday, August 23, 2020 at 2:55 PM From: "Charles Gierke" <cgierke@cox.net> To: "Discussion of CHIRP" <chirp_users@intrepid.danplanet.com>, "Alan Hill" <alan.r.hill@gmail.com> Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating NO luck yet. I held the plug in as far as it would go, no change. I turned the volume up all the way, no luck. I closed CHIRP and re-opened as Administrator,still no luck up or downloading. thanks for your assistance > > On August 22, 2020 at 4:11 PM Alan Hill <alan.r.hill@gmail.com> wrote:Try making sure you vigorously plug the connector into the radio and hold it in while loading from chirp. Also turn the volume up from minimum. Last resort run chirp as adminstrator. On Sat, Aug 22, 2020, 3:45 PM Charles Gierke < cgierke@cox.net mailto:cgierke@cox.net > wrote: > > >On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP. On Friday all I got was the following message: Radio Did Not Respond. I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP. Any suggestions? Thanks Chuck KJ7INT _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Silver Fox at alan.r.hill@gmail.com mailto:alan.r.hill@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com > > _______________________________________________chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com > _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Don Goodrich at don.goodrich@cheerful.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
This may assist. Www.Miklor.com/COM/UV_ErrorMess.php
John Www.Miklor.com/UV5R
On Aug 22, 2020, at 6:45 PM, Charles Gierke cgierke@cox.net wrote:
On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP.
On Friday all I got was the following message: Radio Did Not Respond.
I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP.
Any suggestions?
Thanks Chuck KJ7INT
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Hi; I’m new, however this happened to me several times. I found that if I disconnected the cable and started everything from START, it solved my problem every time...Hope this helps...Like I said I am NEW to this. ;} Regards Ron
Sent from Mailhttps://go.microsoft.com/fwlink/?LinkId=550986 for Windows 10
From: John LaMartinamailto:JohnLa@usa.net Sent: August 22, 2020 8:56 PM To: Discussion of CHIRPmailto:chirp_users@intrepid.danplanet.com Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating
This may assist. Www.Miklor.com/COM/UV_ErrorMess.php
John Www.Miklor.com/UV5R
On Aug 22, 2020, at 6:45 PM, Charles Gierke cgierke@cox.net wrote:
On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP.
On Friday all I got was the following message: Radio Did Not Respond.
I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP.
Any suggestions?
Thanks Chuck KJ7INT _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
thanks for the reply. I will be trying everything tomorrow
On August 22, 2020 at 7:10 PM R G mettle777@outlook.com wrote:
Hi; I’m new, however this happened to me several times. I found that if I disconnected the cable and started everything from START, it solved my problem every time...Hope this helps...Like I said I am NEW to this. ;} Regards Ron Sent from Mail https://go.microsoft.com/fwlink/?LinkId=550986 for Windows 10 From: John LaMartina mailto:JohnLa@usa.net Sent: August 22, 2020 8:56 PM To: Discussion of CHIRP mailto:chirp_users@intrepid.danplanet.com Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating This may assist. Www.Miklor.com/COM/UV_ErrorMess.php John Www.Miklor.com/UV5R > >On Aug 22, 2020, at 6:45 PM, Charles Gierke <cgierke@cox.net> wrote: >> > On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP. On Friday all I got was the following message: Radio Did Not Respond. I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP. Any suggestions? Thanks Chuck KJ7INT >_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
hi, no luck. I tried disconnecting the cable and re-inserting the cable. no luck, the problem is occurring between 3 and 4 seconds into the program.
thanks for the suggestion
On August 22, 2020 at 7:10 PM R G mettle777@outlook.com wrote:
Hi; I’m new, however this happened to me several times. I found that if I disconnected the cable and started everything from START, it solved my problem every time...Hope this helps...Like I said I am NEW to this. ;} Regards Ron Sent from Mail https://go.microsoft.com/fwlink/?LinkId=550986 for Windows 10 From: John LaMartina mailto:JohnLa@usa.net Sent: August 22, 2020 8:56 PM To: Discussion of CHIRP mailto:chirp_users@intrepid.danplanet.com Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating This may assist. Www.Miklor.com/COM/UV_ErrorMess.php John Www.Miklor.com/UV5R > >On Aug 22, 2020, at 6:45 PM, Charles Gierke <cgierke@cox.net> wrote: >> > On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP. On Friday all I got was the following message: Radio Did Not Respond. I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP. Any suggestions? Thanks Chuck KJ7INT >_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Aside from pushing in the plug, would a little twisting to seat the prongs be good or bad?
On August 22, 2020 at 5:55 PM John LaMartina JohnLa@usa.net wrote:
This may assist. Www.Miklor.com/COM/UV_ErrorMess.php John Www.Miklor.com/UV5R > > On Aug 22, 2020, at 6:45 PM, Charles Gierke <cgierke@cox.net> wrote:>> > On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP. On Friday all I got was the following message: Radio Did Not Respond. I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP. Any suggestions? Thanks Chuck KJ7INT _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com >
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
hi, still no luck. I went to the web site and put a death-grip on the plug and held it in as far as it would go. I trimmed a hair of the edges of the plug to let it seat on the bottom.
thanks for the suggestions
On August 22, 2020 at 5:55 PM John LaMartina JohnLa@usa.net wrote:
This may assist. Www.Miklor.com/COM/UV_ErrorMess.php John Www.Miklor.com/UV5R > > On Aug 22, 2020, at 6:45 PM, Charles Gierke <cgierke@cox.net> wrote:>> > On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP. On Friday all I got was the following message: Radio Did Not Respond. I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP. Any suggestions? Thanks Chuck KJ7INT _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com >
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Might help if we knew where you were located.
On 23 August 2020 at 18:04 Charles Gierke cgierke@cox.net wrote:
hi, still no luck. I went to the web site and put a death-grip on the plug and held it in as far as it would go. I trimmed a hair of the edges of the plug to let it seat on the bottom. thanks for the suggestions > > On August 22, 2020 at 5:55 PM John LaMartina <JohnLa@usa.net> wrote:This may assist. Www.Miklor.com/COM/UV_ErrorMess.php John Www.Miklor.com/UV5R > > > On Aug 22, 2020, at 6:45 PM, Charles Gierke <cgierke@cox.net> wrote:> >> > >On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP. On Friday all I got was the following message: Radio Did Not Respond. I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP. Any suggestions? Thanks Chuck KJ7INT _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com > >>> > _______________________________________________chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com > _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Nigel Gunn, W8IFF at nigel@ngunn.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Nigel A. Gunn, ///shoulders.outwards.resolutions tel +1-937-971-0366 Amateur Radio G8IFF W8IFF and GMRS WRBV701, e-mail nigel@ngunn.net www http://www.ngunn.net
Scottsdale AZ.
On August 23, 2020 at 3:29 PM "Nigel A. Gunn G8IFF/W8IFF" nigel@ngunn.net wrote:
Might help if we knew where you were located. > > On 23 August 2020 at 18:04 Charles Gierke <cgierke@cox.net> wrote:hi, still no luck. I went to the web site and put a death-grip on the plug and held it in as far as it would go. I trimmed a hair of the edges of the plug to let it seat on the bottom. thanks for the suggestions > > > On August 22, 2020 at 5:55 PM John LaMartina <JohnLa@usa.net> wrote:This may assist. Www.Miklor.com/COM/UV_ErrorMess.php John Www.Miklor.com/UV5R > > > > On Aug 22, 2020, at 6:45 PM, Charles Gierke <cgierke@cox.net> wrote:> > >> > > >On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP. On Friday all I got was the following message: Radio Did Not Respond. I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP. Any suggestions? Thanks Chuck KJ7INT _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com > > >> >> > > _______________________________________________chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com > > _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Nigel Gunn, W8IFF at nigel@ngunn.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com>Nigel A. Gunn, ///shoulders.outwards.resolutions tel +1-937-971-0366 Amateur Radio G8IFF W8IFF and GMRS WRBV701, e-mail nigel@ngunn.net www http://www.ngunn.net
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
I forgot that you are on Windows. The windows OS is very poor supporting USB. You might try going into the device manager and tell it to show hidden devices. Once that is done, look at the USB entries and delete all of them that are diminished icons. That is, they are lighter than the other icons. Good luck. Alan
From: chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Charles Gierke Sent: Sunday, August 23, 2020 3:05 PM To: Discussion of CHIRP; John LaMartina Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating
hi, still no luck. I went to the web site and put a death-grip on the plug and held it in as far as it would go. I trimmed a hair of the edges of the plug to let it seat on the bottom.
thanks for the suggestions
On August 22, 2020 at 5:55 PM John LaMartina JohnLa@usa.net wrote: This may assist. Www.Miklor.com/COM/UV_ErrorMess.php
John Www.Miklor.com/UV5R
On Aug 22, 2020, at 6:45 PM, Charles Gierke cgierke@cox.net wrote: On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP. On Friday all I got was the following message: Radio Did Not Respond. I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP.
Any suggestions? Thanks Chuck KJ7INT _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
thanks for the suggestion. Unfortunately, no luck.
Chuck
On August 23, 2020 at 4:26 PM Silverfox alan.r.hill@gmail.com wrote:
I forgot that you are on Windows. The windows OS is very poor supporting USB. You might try going into the device manager and tell it to show hidden devices. Once that is done, look at the USB entries and delete all of them that are diminished icons. That is, they are lighter than the other icons. Good luck. Alan From: chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Charles Gierke Sent: Sunday, August 23, 2020 3:05 PM To: Discussion of CHIRP; John LaMartina Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating hi, still no luck. I went to the web site and put a death-grip on the plug and held it in as far as it would go. I trimmed a hair of the edges of the plug to let it seat on the bottom. thanks for the suggestions <br<![endif] --> </br<![endif]> On August 22, 2020 at 5:55 PM John LaMartina <JohnLa@usa.net> wrote: This may assist. Www.Miklor.com/COM/UV_ErrorMess.php John Www.Miklor.com/UV5R <br<![endif] --> </br<![endif]> On Aug 22, 2020, at 6:45 PM, Charles Gierke <cgierke@cox.net> wrote: > > On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP. On Friday all I got was the following message: Radio Did Not Respond. I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP. Any suggestions? Thanks Chuck KJ7INT _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com >_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Chuck, Have you tried the following? open device manager, and seeing which com ports show, and then unplug the cable, and see which one disappears, so you can select that port in Chirp. HTH.
Glenn
----- Original Message ----- From: Charles Gierke To: Discussion of CHIRP ; Silverfox ; John LaMartina Sent: Monday, August 24, 2020 7:43 PM Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating
thanks for the suggestion. Unfortunately, no luck.
Chuck
On August 23, 2020 at 4:26 PM Silverfox alan.r.hill@gmail.com wrote:
I forgot that you are on Windows. The windows OS is very poor supporting USB. You might try going into the device manager and tell it to show hidden devices. Once that is done, look at the USB entries and delete all of them that are diminished icons. That is, they are lighter than the other icons.
Good luck.
Alan
From: chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Charles Gierke Sent: Sunday, August 23, 2020 3:05 PM To: Discussion of CHIRP; John LaMartina Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating
hi, still no luck. I went to the web site and put a death-grip on the plug and held it in as far as it would go. I trimmed a hair of the edges of the plug to let it seat on the bottom.
thanks for the suggestions
<!--[endif]-->
On August 22, 2020 at 5:55 PM John LaMartina JohnLa@usa.net wrote:
This may assist.
Www.Miklor.com/COM/UV_ErrorMess.php
John
Www.Miklor.com/UV5R
<!--[endif]-->
On Aug 22, 2020, at 6:45 PM, Charles Gierke cgierke@cox.net wrote:
On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP.
On Friday all I got was the following message: Radio Did Not Respond.
I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP.
Any suggestions?
Thanks Chuck KJ7INT
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
--------------------------------------------------------------------------------
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Glenn at glennervin@cableone.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Opened Device Manager, Ports (COM & LPT) "USB-SERIAL CH340(COM3)" I've always used COM 3 and it worked fine until last Wednesday.
On August 24, 2020 at 5:48 PM Glenn K0LNY glennervin@cableone.net wrote:
Chuck, Have you tried the following? open device manager, and seeing which com ports show, and then unplug the cable, and see which one disappears, so you can select that port in Chirp. HTH. Glenn ----- Original Message ----- From: Charles Gierke mailto:cgierke@cox.net To: Discussion of CHIRP mailto:chirp_users@intrepid.danplanet.com ; Silverfox mailto:alan.r.hill@gmail.com ; John LaMartina mailto:JohnLa@usa.net Sent: Monday, August 24, 2020 7:43 PM Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating thanks for the suggestion. Unfortunately, no luck. Chuck > > On August 23, 2020 at 4:26 PM Silverfox < alan.r.hill@gmail.com mailto:alan.r.hill@gmail.com > wrote:I forgot that you are on Windows. The windows OS is very poor supporting USB. You might try going into the device manager and tell it to show hidden devices. Once that is done, look at the USB entries and delete all of them that are diminished icons. That is, they are lighter than the other icons. Good luck. Alan From: chirp_users-bounces@intrepid.danplanet.com mailto:chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Charles Gierke Sent: Sunday, August 23, 2020 3:05 PM To: Discussion of CHIRP; John LaMartina Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating hi, still no luck. I went to the web site and put a death-grip on the plug and held it in as far as it would go. I trimmed a hair of the edges of the plug to let it seat on the bottom. thanks for the suggestions <!--[endif]--> On August 22, 2020 at 5:55 PM John LaMartina <JohnLa@usa.net> wrote: This may assist. Www.Miklor.com/COM/UV_ErrorMess.php John Www.Miklor.com/UV5R <!--[endif]--> On Aug 22, 2020, at 6:45 PM, Charles Gierke <cgierke@cox.net> wrote: > > > On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP. On Friday all I got was the following message: Radio Did Not Respond. I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP. Any suggestions? Thanks Chuck KJ7INT _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com > >_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com >> > _______________________________________________chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com >--------------------------------------------- _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Glenn at glennervin@cableone.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Have you had a Windows update that has taken your CH340 driver out? Windows has a habit of removing unsigned drivers.
On 24 August 2020 at 20:57 Charles Gierke cgierke@cox.net wrote:
Opened Device Manager, Ports (COM & LPT) "USB-SERIAL CH340(COM3)" I've always used COM 3 and it worked fine until last Wednesday. > > On August 24, 2020 at 5:48 PM Glenn K0LNY <glennervin@cableone.net> wrote:Chuck, Have you tried the following? open device manager, and seeing which com ports show, and then unplug the cable, and see which one disappears, so you can select that port in Chirp. HTH. Glenn ----- Original Message ----- From: Charles Gierke mailto:cgierke@cox.net To: Discussion of CHIRP mailto:chirp_users@intrepid.danplanet.com ; Silverfox mailto:alan.r.hill@gmail.com ; John LaMartina mailto:JohnLa@usa.net Sent: Monday, August 24, 2020 7:43 PM Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating thanks for the suggestion. Unfortunately, no luck. Chuck > > > On August 23, 2020 at 4:26 PM Silverfox < alan.r.hill@gmail.com mailto:alan.r.hill@gmail.com > wrote:I forgot that you are on Windows. The windows OS is very poor supporting USB. You might try going into the device manager and tell it to show hidden devices. Once that is done, look at the USB entries and delete all of them that are diminished icons. That is, they are lighter than the other icons. Good luck. Alan From: chirp_users-bounces@intrepid.danplanet.com mailto:chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Charles Gierke Sent: Sunday, August 23, 2020 3:05 PM To: Discussion of CHIRP; John LaMartina Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating hi, still no luck. I went to the web site and put a death-grip on the plug and held it in as far as it would go. I trimmed a hair of the edges of the plug to let it seat on the bottom. thanks for the suggestions <!--[endif]--> On August 22, 2020 at 5:55 PM John LaMartina <JohnLa@usa.net> wrote: This may assist. Www.Miklor.com/COM/UV_ErrorMess.php John Www.Miklor.com/UV5R <!--[endif]--> On Aug 22, 2020, at 6:45 PM, Charles Gierke <cgierke@cox.net> wrote: > > > >On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP. On Friday all I got was the following message: Radio Did Not Respond. I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP. Any suggestions? Thanks Chuck KJ7INT _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com > > >_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com > >> > > _______________________________________________chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com > >--------------------------------------------- _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Glenn at glennervin@cableone.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com >> > _______________________________________________chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com > _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Nigel Gunn, W8IFF at nigel@ngunn.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Nigel A. Gunn, ///shoulders.outwards.resolutions tel +1-937-971-0366 Amateur Radio G8IFF W8IFF and GMRS WRBV701, e-mail nigel@ngunn.net www http://www.ngunn.net
Installed driver is the latest version
On August 24, 2020 at 6:09 PM "Nigel A. Gunn G8IFF/W8IFF" nigel@ngunn.net wrote:
Have you had a Windows update that has taken your CH340 driver out? Windows has a habit of removing unsigned drivers. > > On 24 August 2020 at 20:57 Charles Gierke <cgierke@cox.net> wrote:Opened Device Manager, Ports (COM & LPT) "USB-SERIAL CH340(COM3)" I've always used COM 3 and it worked fine until last Wednesday. > > > On August 24, 2020 at 5:48 PM Glenn K0LNY <glennervin@cableone.net> wrote:Chuck, Have you tried the following? open device manager, and seeing which com ports show, and then unplug the cable, and see which one disappears, so you can select that port in Chirp. HTH. Glenn ----- Original Message ----- From: Charles Gierke mailto:cgierke@cox.net To: Discussion of CHIRP mailto:chirp_users@intrepid.danplanet.com ; Silverfox mailto:alan.r.hill@gmail.com ; John LaMartina mailto:JohnLa@usa.net Sent: Monday, August 24, 2020 7:43 PM Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating thanks for the suggestion. Unfortunately, no luck. Chuck > > > > On August 23, 2020 at 4:26 PM Silverfox < alan.r.hill@gmail.com mailto:alan.r.hill@gmail.com > wrote:I forgot that you are on Windows. The windows OS is very poor supporting USB. You might try going into the device manager and tell it to show hidden devices. Once that is done, look at the USB entries and delete all of them that are diminished icons. That is, they are lighter than the other icons. Good luck. Alan From: chirp_users-bounces@intrepid.danplanet.com mailto:chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Charles Gierke Sent: Sunday, August 23, 2020 3:05 PM To: Discussion of CHIRP; John LaMartina Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating hi, still no luck. I went to the web site and put a death-grip on the plug and held it in as far as it would go. I trimmed a hair of the edges of the plug to let it seat on the bottom. thanks for the suggestions <!--[endif]--> On August 22, 2020 at 5:55 PM John LaMartina <JohnLa@usa.net> wrote: This may assist. Www.Miklor.com/COM/UV_ErrorMess.php John Www.Miklor.com/UV5R <!--[endif]--> On Aug 22, 2020, at 6:45 PM, Charles Gierke <cgierke@cox.net> wrote: > > > > >On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP. On Friday all I got was the following message: Radio Did Not Respond. I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP. Any suggestions? Thanks Chuck KJ7INT _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com > > > >_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com > > >> > > > _______________________________________________chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com > > >--------------------------------------------- _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Glenn at glennervin@cableone.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com > >> > > _______________________________________________chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com > > _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Nigel Gunn, W8IFF at nigel@ngunn.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com>Nigel A. Gunn, ///shoulders.outwards.resolutions tel +1-937-971-0366 Amateur Radio G8IFF W8IFF and GMRS WRBV701, e-mail nigel@ngunn.net www http://www.ngunn.net
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Hello,
I have programed well over a hundred UV-5x radios and have had both easy and hard times programing them.
One thing that I learned is to slow down, waiting about 10 seconds between actions taken on the computer. This solve most of the error problems.
If that does not work, most of the rest to the time ,it is solved by pushing the programing cable into the radio and keep pressure on the cable until the pride is programed. I have to push it VERY hard.
On a windows machines you have to select the right com port (I am mostly a mac person so I find the right port by trial and error).
As an aside, using more that 60 cables to program the radios, I have only found one cable that was defective, so that is most likely, not the problem. ----- Peter J. McClosky, N7IY Eugene, Oregon pmcclosky@earthlink.net n7iy@arrl.net http://home.earthlink.net/~pmcclosky/
On Aug 24, 2020, at 5:43 PM, Charles Gierke cgierke@cox.net wrote:
thanks for the suggestion. Unfortunately, no luck.
Chuck
On August 23, 2020 at 4:26 PM Silverfox <alan.r.hill@gmail.com mailto:alan.r.hill@gmail.com> wrote:
I forgot that you are on Windows. The windows OS is very poor supporting USB. You might try going into the device manager and tell it to show hidden devices. Once that is done, look at the USB entries and delete all of them that are diminished icons. That is, they are lighter than the other icons. Good luck. Alan
From: chirp_users-bounces@intrepid.danplanet.com mailto:chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Charles Gierke Sent: Sunday, August 23, 2020 3:05 PM To: Discussion of CHIRP; John LaMartina Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating
hi, still no luck. I went to the web site and put a death-grip on the plug and held it in as far as it would go. I trimmed a hair of the edges of the plug to let it seat on the bottom.
thanks for the suggestions
On August 22, 2020 at 5:55 PM John LaMartina <JohnLa@usa.net mailto:JohnLa@usa.net> wrote:
This may assist. Www.Miklor.com/COM/UV_ErrorMess.php http://www.miklor.com/COM/UV_ErrorMess.php
John Www.Miklor.com/UV5R http://www.miklor.com/UV5R
On Aug 22, 2020, at 6:45 PM, Charles Gierke <cgierke@cox.net mailto:cgierke@cox.net> wrote:
On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP.
On Friday all I got was the following message: Radio Did Not Respond.
I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP.
Any suggestions?
Thanks Chuck KJ7INT
chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net mailto:johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net mailto:cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net mailto:cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Peter at pmcclosky@earthlink.net mailto:pmcclosky@earthlink.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com
HI, I followed your advice and took it slow. I waited a minimum of 10 seconds, I put a strangle hold on the plug and radio to insure the plug was fully into the socket. I double checked the USB plug was in the USB socket and it was connected to the Win 10 computer as COM 3.
the radio is still not connecting to CHIRP. About 3 seconds after starting the download, the radio seems to shut itself off and restart.
thanks for your time and help. Chuck
On August 24, 2020 at 6:09 PM "Peter J. McClosky" pmcclosky@earthlink.net wrote:
Hello, I have programed well over a hundred UV-5x radios and have had both easy and hard times programing them. One thing that I learned is to slow down, waiting about 10 seconds between actions taken on the computer. This solve most of the error problems. If that does not work, most of the rest to the time ,it is solved by pushing the programing cable into the radio and keep pressure on the cable until the pride is programed. I have to push it VERY hard. On a windows machines you have to select the right com port (I am mostly a mac person so I find the right port by trial and error). As an aside, using more that 60 cables to program the radios, I have only found one cable that was defective, so that is most likely, not the problem. ----- Peter J. McClosky, N7IY Eugene, Oregon pmcclosky@earthlink.net mailto:pmcclosky@earthlink.net n7iy@arrl.net http://home.earthlink.net/~pmcclosky/ > > On Aug 24, 2020, at 5:43 PM, Charles Gierke < cgierke@cox.net mailto:cgierke@cox.net > wrote:thanks for the suggestion. Unfortunately, no luck. Chuck > > > On August 23, 2020 at 4:26 PM Silverfox < alan.r.hill@gmail.com mailto:alan.r.hill@gmail.com > wrote:I forgot that you are on Windows. The windows OS is very poor supporting USB. You might try going into the device manager and tell it to show hidden devices. Once that is done, look at the USB entries and delete all of them that are diminished icons. That is, they are lighter than the other icons. Good luck. Alan From: chirp_users-bounces@intrepid.danplanet.com mailto:chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Charles Gierke Sent: Sunday, August 23, 2020 3:05 PM To: Discussion of CHIRP; John LaMartina Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating hi, still no luck. I went to the web site and put a death-grip on the plug and held it in as far as it would go. I trimmed a hair of the edges of the plug to let it seat on the bottom. thanks for the suggestions On August 22, 2020 at 5:55 PM John LaMartina <JohnLa@usa.net mailto:JohnLa@usa.net > wrote: This may assist. Www.Miklor.com/COM/UV_ErrorMess.php http://www.miklor.com/COM/UV_ErrorMess.php John Www.Miklor.com/UV5R http://www.miklor.com/UV5R On Aug 22, 2020, at 6:45 PM, Charles Gierke <cgierke@cox.net mailto:cgierke@cox.net > wrote: > > > > On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP. On Friday all I got was the following message: Radio Did Not Respond. I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP. Any suggestions? Thanks Chuck KJ7INT _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net mailto:johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com > > >_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net mailto:cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com > >> > > _______________________________________________chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net mailto:cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com > > _______________________________________________chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Peter at pmcclosky@earthlink.net mailto:pmcclosky@earthlink.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com >
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Hi Chuck, Could it be that your battery is the problem? Can you keep it in the charging cradle while doing the Chirp work? HTH. Glenn ----- Original Message ----- From: Charles Gierke To: Discussion of CHIRP ; Peter J. McClosky Sent: Tuesday, August 25, 2020 1:27 PM Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating
HI, I followed your advice and took it slow. I waited a minimum of 10 seconds, I put a strangle hold on the plug and radio to insure the plug was fully into the socket. I double checked the USB plug was in the USB socket and it was connected to the Win 10 computer as COM 3.
the radio is still not connecting to CHIRP. About 3 seconds after starting the download, the radio seems to shut itself off and restart.
thanks for your time and help. Chuck
On August 24, 2020 at 6:09 PM "Peter J. McClosky" pmcclosky@earthlink.net wrote:
Hello,
I have programed well over a hundred UV-5x radios and have had both easy and hard times programing them.
One thing that I learned is to slow down, waiting about 10 seconds between actions taken on the computer. This solve most of the error problems.
If that does not work, most of the rest to the time ,it is solved by pushing the programing cable into the radio and keep pressure on the cable until the pride is programed. I have to push it VERY hard.
On a windows machines you have to select the right com port (I am mostly a mac person so I find the right port by trial and error).
As an aside, using more that 60 cables to program the radios, I have only found one cable that was defective, so that is most likely, not the problem.
----- Peter J. McClosky, N7IY Eugene, Oregon pmcclosky@earthlink.net n7iy@arrl.net http://home.earthlink.net/~pmcclosky/
On Aug 24, 2020, at 5:43 PM, Charles Gierke < cgierke@cox.net> wrote:
thanks for the suggestion. Unfortunately, no luck.
Chuck
On August 23, 2020 at 4:26 PM Silverfox < alan.r.hill@gmail.com> wrote:
I forgot that you are on Windows. The windows OS is very poor supporting USB. You might try going into the device manager and tell it to show hidden devices. Once that is done, look at the USB entries and delete all of them that are diminished icons. That is, they are lighter than the other icons. Good luck. Alan
From: chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Charles Gierke Sent: Sunday, August 23, 2020 3:05 PM To: Discussion of CHIRP; John LaMartina Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating
hi, still no luck. I went to the web site and put a death-grip on the plug and held it in as far as it would go. I trimmed a hair of the edges of the plug to let it seat on the bottom.
thanks for the suggestions
<!--[endif]--> On August 22, 2020 at 5:55 PM John LaMartina JohnLa@usa.net wrote:
This may assist. Www.Miklor.com/COM/UV_ErrorMess.php
John Www.Miklor.com/UV5R
<!--[endif]--> On Aug 22, 2020, at 6:45 PM, Charles Gierke cgierke@cox.net wrote:
On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP.
On Friday all I got was the following message: Radio Did Not Respond.
I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP.
Any suggestions?
Thanks Chuck KJ7INT
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Peter at pmcclosky@earthlink.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
--------------------------------------------------------------------------------
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Glenn at glennervin@cableone.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Just tried your suggestion. same problem
thanks for trying
On August 25, 2020 at 11:31 AM Glenn K0LNY glennervin@cableone.net wrote:
Hi Chuck, Could it be that your battery is the problem? Can you keep it in the charging cradle while doing the Chirp work? HTH. Glenn ----- Original Message ----- From: Charles Gierke mailto:cgierke@cox.net To: Discussion of CHIRP mailto:chirp_users@intrepid.danplanet.com ; Peter J. McClosky mailto:pmcclosky@earthlink.net Sent: Tuesday, August 25, 2020 1:27 PM Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating HI, I followed your advice and took it slow. I waited a minimum of 10 seconds, I put a strangle hold on the plug and radio to insure the plug was fully into the socket. I double checked the USB plug was in the USB socket and it was connected to the Win 10 computer as COM 3. the radio is still not connecting to CHIRP. About 3 seconds after starting the download, the radio seems to shut itself off and restart. thanks for your time and help. Chuck > > On August 24, 2020 at 6:09 PM "Peter J. McClosky" <pmcclosky@earthlink.net> wrote:Hello, I have programed well over a hundred UV-5x radios and have had both easy and hard times programing them. One thing that I learned is to slow down, waiting about 10 seconds between actions taken on the computer. This solve most of the error problems. If that does not work, most of the rest to the time ,it is solved by pushing the programing cable into the radio and keep pressure on the cable until the pride is programed. I have to push it VERY hard. On a windows machines you have to select the right com port (I am mostly a mac person so I find the right port by trial and error). As an aside, using more that 60 cables to program the radios, I have only found one cable that was defective, so that is most likely, not the problem. ----- Peter J. McClosky, N7IY Eugene, Oregon pmcclosky@earthlink.net mailto:pmcclosky@earthlink.net n7iy@arrl.net http://home.earthlink.net/~pmcclosky/ > > > On Aug 24, 2020, at 5:43 PM, Charles Gierke < cgierke@cox.net mailto:cgierke@cox.net > wrote:thanks for the suggestion. Unfortunately, no luck. Chuck > > > > On August 23, 2020 at 4:26 PM Silverfox < alan.r.hill@gmail.com mailto:alan.r.hill@gmail.com > wrote:I forgot that you are on Windows. The windows OS is very poor supporting USB. You might try going into the device manager and tell it to show hidden devices. Once that is done, look at the USB entries and delete all of them that are diminished icons. That is, they are lighter than the other icons. Good luck. Alan From: chirp_users-bounces@intrepid.danplanet.com mailto:chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Charles Gierke Sent: Sunday, August 23, 2020 3:05 PM To: Discussion of CHIRP; John LaMartina Subject: Re: [chirp_users] Chirp and BaoFeng UV 5R not communicating hi, still no luck. I went to the web site and put a death-grip on the plug and held it in as far as it would go. I trimmed a hair of the edges of the plug to let it seat on the bottom. thanks for the suggestions <!--[endif]--> On August 22, 2020 at 5:55 PM John LaMartina <JohnLa@usa.net mailto:JohnLa@usa.net > wrote: This may assist. Www.Miklor.com/COM/UV_ErrorMess.php http://www.miklor.com/COM/UV_ErrorMess.php John Www.Miklor.com/UV5R http://www.miklor.com/UV5R <!--[endif]--> On Aug 22, 2020, at 6:45 PM, Charles Gierke <cgierke@cox.net mailto:cgierke@cox.net > wrote: > > > > > On Wednesday my 2 BaoFeng UV 5R radios could download and upload to CHIRP. On Friday all I got was the following message: Radio Did Not Respond. I tried reloading the latest version of CHIRP, no change. I tried an earlier version of CHIRP, no change. I reloaded the latest version back, no change. Visually the radio's red light blinks then the LED display blinks then the error message shows up on CHIRP. Any suggestions? Thanks Chuck KJ7INT _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net mailto:johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com > > > >_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net mailto:cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com > > >> > > > _______________________________________________chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net mailto:cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com > > > _______________________________________________chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Peter at pmcclosky@earthlink.net mailto:pmcclosky@earthlink.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com > >>> > _______________________________________________chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com >--------------------------------------------- _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Glenn at glennervin@cableone.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck at cgierke@cox.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
participants (14)
-
Alan Hill -
Brian Erickson -
Charles Gierke -
Don Goodrich -
Gary A. Cox -
Glenn K0LNY -
Jardy -
Jardy Dawson
-
Jim Unroe -
John LaMartina -
Nigel A. Gunn G8IFF/W8IFF -
Peter J. McClosky -
R G -
Silverfox