- Developers - lists.chirpmyradio.com

Re: [chirp_devel] [PATCH] [TK-270] Allow programming Kenwood commercial UHF radios in the 70cm band. #4709
by Pavel Milanes Costa 03 May '17

03 May '17

Hi, sorry for the delay, the wait is justified. Attached to this email I send to you a short survey about the OEM vs Real limits of some of the Commercial Kenwoods radios. (VHF and UHF). In past days I asked some of my ham fellow to pass by my home and borrow his radios for a few minutes; the test was to put a 0.5 Mhz jumps in the channels of the radios and check where they fail to look the PLL VCOs, sure I tested them on either mode (RX o TX) data shows that RX will go about -6% in the lower edge and is the first to fail in the upper edge with a mean of a +4.0% (in one case TX can work up to 8%!) In short: either VHF or UHF models can tolerate safely a -4% and + 4% as a rule of thumb (working on both RX & TX), data from my experiments shows that in most cases this is safe. As -4.0% is the minimum that will allow to work the ham bands either on VHF as in UHF I will set a +/- 4% on both edges. So, I'm submitting patched to the 3 drivers that support the tested Commercial Kenwood radios, I will create a new issue explaining the situation and data found and will send the 3 independent patches against this issue, I will link the Tom's issue as a subset of this. This will allow to use that radios in Ham bands and yet the OEM ident/model string in the settings area will show the real OEM values, just as Tom suggested. 73 de Pavel CO7WT.

1 0

[chirp_devel] Build test results: Failure
by Build System 30 Apr '17

30 Apr '17

Tested changes: [Ray Cielencki <rayslinky(a)gmail.com>] [VX-3] fix bank_used issue #1203 This patch works around #1203 -- where banks are not properly marked as used. Additionally, it corrects how bank_used values are calculated. [SASANO Takayoshi <uaa(a)mx5.nisiq.net>] Bug#4771, add high-speed (38400bps) cloning to IC-P7 [SASANO Takayoshi <uaa(a)mx5.nisiq.net>] Bug #4769 remove meaningless _mem.set_raw("\x00" * (_mem.size() / 8)) line, all elements are filled when setting/emptying entry. [Richard Birch <n7uoa.birch(a)gmail.com>] [vx5] Corrected checksum and added prompts Fixes #4749 [Dan Smith <dsmith(a)danplanet.com>] Add Rugged RH5R G2 #0 [Tom Hayward <tom(a)tomh.us>] [id880] Fix typo in charset definition. #281 [Tom Hayward <tom(a)tomh.us>] [thf6a] Support full charset (ASCII). Fixes #141 [Tom Hayward <tom(a)tomh.us>] [id880] Support full charset. Fixes #281 [Tom Hayward <tom(a)tomh.us>] [vx5] Support full charset (ASCII). Fixes #292 [Tom Hayward <tom(a)tomh.us>] [id31a] set used bit when creating new memory, clear when deleting. Fixes #269 [Tom Hayward <tom(a)tomh.us>] Support PyGTK < 2.22 in bank edit. Fixes #231 [Tom Hayward <tom(a)tomh.us>] [d710] [v71] [d72] Fix tone list (not all tones are supported). Fixes #212 [Dan Smith <dsmith(a)danplanet.com>] [vx7] Fix setting memory power levels on 220MHz band Fixes #214 [Dan Smith <dsmith(a)danplanet.com>] fips: Pennsylvania FIPS code was wrong. #117 [Marco Filippi <iz3gme.marco(a)gmail.com>] Consider lower bound frequency of each valid_band as valid Fix bug #181 [Tom Hayward <tom(a)tomh.us>] tmd700: allow 8-char names. Fixes #176 [Dan Smith <dsmith(a)danplanet.com>] Fix the "blind deletion" problem, as well as properly direct copy/paste Fixes #172 [David Griffith <dave(a)661.org>] Bug #155 fix: VX-7 1.25m power levels [David Griffith <dave(a)661.org>] New INSTALL and README files Fixes #122 [Tom Hayward <tom(a)tomh.us>] thd72: only use hardware flow on OS X. Fixes #166 [Marco Filippi <iz3gme.marco(a)gmail.com>] [FT817] Tone freq not set correctly Same as #88 for FT857, to avoid code duplication fix code have been moved from ft857 to its ancestor class Fix bug #163 [Tom Hayward <tom(a)tomh.us>] Fix Mac .app so paths with spaces work. Fixes Bug #145 Full log: Started by an SCM change Building in workspace /var/lib/jenkins/jobs/chirp-test/workspace [workspace] $ hg showconfig paths.default [workspace] $ hg pull --rev default [workspace] $ hg update --clean --rev default 5 files updated, 0 files merged, 0 files removed, 0 files unresolved [workspace] $ hg log --rev . --template {node} [workspace] $ hg log --rev . --template {rev} [workspace] $ hg log --rev 7fe5f7b14be57479d4d37c9e204caf6a076b5d18 [workspace] $ hg log --template "<changeset node='{node}' author='{author|xmlescape}' rev='{rev}' date='{date}'><msg>{desc|xmlescape}</msg><added>{file_adds|stringify|xmlescape}</added><deleted>{file_dels|stringify|xmlescape}</deleted><files>{files|stringify|xmlescape}</files><parents>{parents}</parents></changeset>\n" --rev default:0 --follow --prune 7fe5f7b14be57479d4d37c9e204caf6a076b5d18 No emails were triggered. [workspace] $ /bin/sh -xe /tmp/hudson3045486650759912958.sh [workspace] $ /bin/sh -xe /tmp/hudson8467155497089852769.sh + PATH=/usr/bin:/bin:/usr/local/bin ./run_all_tests.sh test_bit_array (tests.unit.test_bitwise.TestBitType) ... ok test_bit_array_fail (tests.unit.test_bitwise.TestBitType) ... ok test_bitfield_u16 (tests.unit.test_bitwise.TestBitfieldTypes) ... ok test_bitfield_u24 (tests.unit.test_bitwise.TestBitfieldTypes) ... ok test_bitfield_u8 (tests.unit.test_bitwise.TestBitfieldTypes) ... ok test_bitfield_ul16 (tests.unit.test_bitwise.TestBitfieldTypes) ... ok test_bitfield_ul24 (tests.unit.test_bitwise.TestBitfieldTypes) ... ok test_bbcd (tests.unit.test_bitwise.TestBitwiseBCDTypes) ... ok test_bbcd_array (tests.unit.test_bitwise.TestBitwiseBCDTypes) ... ok test_lbcd (tests.unit.test_bitwise.TestBitwiseBCDTypes) ... ok test_lbcd_array (tests.unit.test_bitwise.TestBitwiseBCDTypes) ... ok test_int_array (tests.unit.test_bitwise.TestBitwiseBaseIntTypes) ... ok test_type_u16 (tests.unit.test_bitwise.TestBitwiseBaseIntTypes) ... ok test_type_u24 (tests.unit.test_bitwise.TestBitwiseBaseIntTypes) ... ok test_type_u32 (tests.unit.test_bitwise.TestBitwiseBaseIntTypes) ... ok test_type_u8 (tests.unit.test_bitwise.TestBitwiseBaseIntTypes) ... ok test_type_ul16 (tests.unit.test_bitwise.TestBitwiseBaseIntTypes) ... ok test_type_ul24 (tests.unit.test_bitwise.TestBitwiseBaseIntTypes) ... ok test_type_ul32 (tests.unit.test_bitwise.TestBitwiseBaseIntTypes) ... ok test_char (tests.unit.test_bitwise.TestBitwiseCharTypes) ... ok test_string (tests.unit.test_bitwise.TestBitwiseCharTypes) ... ok test_string_invalid_chars (tests.unit.test_bitwise.TestBitwiseCharTypes) ... ok test_string_wrong_length (tests.unit.test_bitwise.TestBitwiseCharTypes) ... ok test_comment_cppstyle (tests.unit.test_bitwise.TestBitwiseComments) ... ok test_comment_inline_cppstyle (tests.unit.test_bitwise.TestBitwiseComments) ... ok test_missing_semicolon (tests.unit.test_bitwise.TestBitwiseErrors) ... ok test_seek (tests.unit.test_bitwise.TestBitwiseSeek) ... ok test_seekto (tests.unit.test_bitwise.TestBitwiseSeek) ... ok test_struct_one_element (tests.unit.test_bitwise.TestBitwiseStructTypes) ... ok test_struct_two_elements (tests.unit.test_bitwise.TestBitwiseStructTypes) ... ok test_struct_writes (tests.unit.test_bitwise.TestBitwiseStructTypes) ... ok split_tone_encode_test_cross_dtcs_tone (tests.unit.test_chirp_common.TestSplitTone) ... ok split_tone_encode_test_cross_none_dtcs (tests.unit.test_chirp_common.TestSplitTone) ... ok split_tone_encode_test_cross_none_tone (tests.unit.test_chirp_common.TestSplitTone) ... ok split_tone_encode_test_cross_tone_dtcs (tests.unit.test_chirp_common.TestSplitTone) ... ok split_tone_encode_test_cross_tone_tone (tests.unit.test_chirp_common.TestSplitTone) ... ok split_tone_encode_test_dtcs (tests.unit.test_chirp_common.TestSplitTone) ... ok split_tone_encode_test_none (tests.unit.test_chirp_common.TestSplitTone) ... ok split_tone_encode_test_tone (tests.unit.test_chirp_common.TestSplitTone) ... ok split_tone_encode_test_tsql (tests.unit.test_chirp_common.TestSplitTone) ... ok test_split_tone_decode_cross_dtcs_dtcs (tests.unit.test_chirp_common.TestSplitTone) ... ok test_split_tone_decode_cross_dtcs_tone (tests.unit.test_chirp_common.TestSplitTone) ... ok test_split_tone_decode_cross_none_dtcs (tests.unit.test_chirp_common.TestSplitTone) ... ok test_split_tone_decode_cross_none_tone (tests.unit.test_chirp_common.TestSplitTone) ... ok test_split_tone_decode_cross_tone_dtcs (tests.unit.test_chirp_common.TestSplitTone) ... ok test_split_tone_decode_cross_tone_tone (tests.unit.test_chirp_common.TestSplitTone) ... ok test_split_tone_decode_dtcs (tests.unit.test_chirp_common.TestSplitTone) ... ok test_split_tone_decode_none (tests.unit.test_chirp_common.TestSplitTone) ... ok test_split_tone_decode_tone (tests.unit.test_chirp_common.TestSplitTone) ... ok test_split_tone_decode_tsql (tests.unit.test_chirp_common.TestSplitTone) ... ok test_fix_rounded_step_250 (tests.unit.test_chirp_common.TestStepFunctions) ... ok test_fix_rounded_step_500 (tests.unit.test_chirp_common.TestStepFunctions) ... ok test_fix_rounded_step_750 (tests.unit.test_chirp_common.TestStepFunctions) ... ok test_is_12_5 (tests.unit.test_chirp_common.TestStepFunctions) ... ok test_is_2_5 (tests.unit.test_chirp_common.TestStepFunctions) ... ok test_is_5_0 (tests.unit.test_chirp_common.TestStepFunctions) ... ok test_is_6_25 (tests.unit.test_chirp_common.TestStepFunctions) ... ok test_is_fractional_step (tests.unit.test_chirp_common.TestStepFunctions) ... ok test_required_step (tests.unit.test_chirp_common.TestStepFunctions) ... ok test_required_step_fail (tests.unit.test_chirp_common.TestStepFunctions) ... ok test_format_freq (tests.unit.test_chirp_common.TestUtilityFunctions) ... ok test_parse_freq_bad (tests.unit.test_chirp_common.TestUtilityFunctions) ... ok test_parse_freq_decimal (tests.unit.test_chirp_common.TestUtilityFunctions) ... ok test_parse_freq_whitespace (tests.unit.test_chirp_common.TestUtilityFunctions) ... ok test_parse_freq_whole (tests.unit.test_chirp_common.TestUtilityFunctions) ... ok test_ensure_has_calls_almost_full (tests.unit.test_import_logic.DstarTests) ... ok test_ensure_has_calls_empty (tests.unit.test_import_logic.DstarTests) ... ok test_ensure_has_calls_partial (tests.unit.test_import_logic.DstarTests) ... ok test_ensure_has_calls_rptcall_full1 (tests.unit.test_import_logic.DstarTests) ... ok test_ensure_has_calls_rptcall_full2 (tests.unit.test_import_logic.DstarTests) ... ok test_ensure_has_calls_urcall_full (tests.unit.test_import_logic.DstarTests) ... ok test_import_bank (tests.unit.test_import_logic.ImportFieldTests) ... ok test_import_dtcs_diffA_dtcs (tests.unit.test_import_logic.ImportFieldTests) ... ok test_import_dtcs_diffB_dtcs (tests.unit.test_import_logic.ImportFieldTests) ... ok test_import_duplex_negative (tests.unit.test_import_logic.ImportFieldTests) ... ok test_import_duplex_too_big_vhf (tests.unit.test_import_logic.ImportFieldTests) ... ok test_import_duplex_uhf (tests.unit.test_import_logic.ImportFieldTests) ... ok test_import_duplex_vhf (tests.unit.test_import_logic.ImportFieldTests) ... ok test_import_mem (tests.unit.test_import_logic.ImportFieldTests) ... ok test_import_mem_with_errors (tests.unit.test_import_logic.ImportFieldTests) ... ok test_import_mem_with_warnings (tests.unit.test_import_logic.ImportFieldTests) ... ok test_import_mode_invalid (tests.unit.test_import_logic.ImportFieldTests) ... ok test_import_mode_valid_am (tests.unit.test_import_logic.ImportFieldTests) ... ok test_import_mode_valid_fm (tests.unit.test_import_logic.ImportFieldTests) ... ok test_import_name (tests.unit.test_import_logic.ImportFieldTests) ... ok test_import_power_closest (tests.unit.test_import_logic.ImportFieldTests) ... ok test_import_power_no_dst (tests.unit.test_import_logic.ImportFieldTests) ... ok test_import_power_no_src (tests.unit.test_import_logic.ImportFieldTests) ... ok test_import_power_same (tests.unit.test_import_logic.ImportFieldTests) ... ok test_import_tone_diffA_tsql (tests.unit.test_import_logic.ImportFieldTests) ... ok test_import_tone_diffB_tsql (tests.unit.test_import_logic.ImportFieldTests) ... ok test_mapping (tests.unit.test_mappingmodel.TestBaseBank) ... ok test_mapping_eq (tests.unit.test_mappingmodel.TestBaseBank) ... ok test_base_class (tests.unit.test_mappingmodel.TestBaseBankModel) ... ok test_get_name (tests.unit.test_mappingmodel.TestBaseBankModel) ... ok test_mapping (tests.unit.test_mappingmodel.TestBaseMapping) ... ok test_mapping_eq (tests.unit.test_mappingmodel.TestBaseMapping) ... ok test_base_class (tests.unit.test_mappingmodel.TestBaseMappingModel) ... ok test_get_name (tests.unit.test_mappingmodel.TestBaseMappingModel) ... ok test_base_class (tests.unit.test_mappingmodel.TestBaseMappingModelIndexInterface) ... ok test_add_memory_to_mapping (tests.unit.test_mappingmodel.TestIcomBankModel) ... ok test_get_mapping_memories (tests.unit.test_mappingmodel.TestIcomBankModel) ... ok test_get_mappings (tests.unit.test_mappingmodel.TestIcomBankModel) ... ok test_get_memory_mappings (tests.unit.test_mappingmodel.TestIcomBankModel) ... ok test_get_num_mappings (tests.unit.test_mappingmodel.TestIcomBankModel) ... ok test_remove_memory_from_mapping (tests.unit.test_mappingmodel.TestIcomBankModel) ... ok test_remove_memory_from_mapping_no_bank (tests.unit.test_mappingmodel.TestIcomBankModel) ... ok test_remove_memory_from_mapping_wrong_bank (tests.unit.test_mappingmodel.TestIcomBankModel) ... ok test_icom_bank (tests.unit.test_mappingmodel.TestIcomBanks) ... ok test_mapping (tests.unit.test_mappingmodel.TestIcomBanks) ... ok test_mapping_eq (tests.unit.test_mappingmodel.TestIcomBanks) ... ok test_add_memory_to_mapping (tests.unit.test_mappingmodel.TestIcomIndexedBankModel) ... ok test_get_index_bounds (tests.unit.test_mappingmodel.TestIcomIndexedBankModel) ... ok test_get_mapping_memories (tests.unit.test_mappingmodel.TestIcomIndexedBankModel) ... ok test_get_mappings (tests.unit.test_mappingmodel.TestIcomIndexedBankModel) ... ok test_get_memory_index (tests.unit.test_mappingmodel.TestIcomIndexedBankModel) ... ok test_get_memory_mappings (tests.unit.test_mappingmodel.TestIcomIndexedBankModel) ... ok test_get_next_mapping_index (tests.unit.test_mappingmodel.TestIcomIndexedBankModel) ... ok test_get_num_mappings (tests.unit.test_mappingmodel.TestIcomIndexedBankModel) ... ok test_remove_memory_from_mapping (tests.unit.test_mappingmodel.TestIcomIndexedBankModel) ... ok test_remove_memory_from_mapping_no_bank (tests.unit.test_mappingmodel.TestIcomIndexedBankModel) ... ok test_remove_memory_from_mapping_wrong_bank (tests.unit.test_mappingmodel.TestIcomIndexedBankModel) ... ok test_set_memory_index (tests.unit.test_mappingmodel.TestIcomIndexedBankModel) ... ok test_set_memory_index_bad_bank (tests.unit.test_mappingmodel.TestIcomIndexedBankModel) ... ok test_set_memory_index_bad_index (tests.unit.test_mappingmodel.TestIcomIndexedBankModel) ... ok test_auto_tone_mode_cross (tests.unit.test_memedit_edits.TestEdits) ... ok test_auto_tone_mode_dtcs (tests.unit.test_memedit_edits.TestEdits) ... ok test_auto_tone_mode_dtcs_pol (tests.unit.test_memedit_edits.TestEdits) ... ok test_auto_tone_mode_dtcs_rx (tests.unit.test_memedit_edits.TestEdits) ... ok test_auto_tone_mode_tone (tests.unit.test_memedit_edits.TestEdits) ... ok test_auto_tone_mode_tsql (tests.unit.test_memedit_edits.TestEdits) ... ok test_init (tests.unit.test_platform.Win32PlatformTest) ... ok test_serial_ports_bad_portnames (tests.unit.test_platform.Win32PlatformTest) ... ok test_serial_ports_sorted (tests.unit.test_platform.Win32PlatformTest) ... ok test_apply_callback (tests.unit.test_settings.TestSettingContainers) ... ok test_radio_setting (tests.unit.test_settings.TestSettingContainers) ... ok test_radio_setting_group (tests.unit.test_settings.TestSettingContainers) ... ok test_radio_setting_multi (tests.unit.test_settings.TestSettingContainers) ... ok test_changed (tests.unit.test_settings.TestSettingValues) ... ok test_radio_setting_value_boolean (tests.unit.test_settings.TestSettingValues) ... ok test_radio_setting_value_float (tests.unit.test_settings.TestSettingValues) ... ok test_radio_setting_value_integer (tests.unit.test_settings.TestSettingValues) ... ok test_radio_setting_value_list (tests.unit.test_settings.TestSettingValues) ... ok test_radio_setting_value_string (tests.unit.test_settings.TestSettingValues) ... ok test_validate_callback (tests.unit.test_settings.TestSettingValues) ... ok test_delete_hole_with_all (tests.unit.test_shiftdialog.ShiftDialogTest) ... ok test_delete_hole_with_all_full (tests.unit.test_shiftdialog.ShiftDialogTest) ... ok test_delete_hole_with_hole (tests.unit.test_shiftdialog.ShiftDialogTest) ... ok test_delete_hole_without_hole (tests.unit.test_shiftdialog.ShiftDialogTest) ... ok test_insert_hole_with_space (tests.unit.test_shiftdialog.ShiftDialogTest) ... ok test_insert_hole_without_space (tests.unit.test_shiftdialog.ShiftDialogTest) ... ok ---------------------------------------------------------------------- Ran 151 tests in 0.053s OK Patch 'tip' is OK Checking for PEP8 regressions... ./chirp/drivers/icf.py:202:26: E261 at least two spaces before inline comment ./chirp/drivers/icf.py:266:30: E261 at least two spaces before inline comment ./chirp/platform.py:255:80: E501 line too long (82 > 79 characters) ./chirp/ui/mainapp.py:1909:80: E501 line too long (82 > 79 characters) ./chirp/ui/mainapp.py:1965:80: E501 line too long (82 > 79 characters) real 0m7.678s user 0m7.556s sys 0m0.032s ================================================ Tests FAILED: driver tests Build step 'Execute shell' marked build as failure Email was triggered for: Failure Sending email for trigger: Failure

1 1

[chirp_devel] [PATCH] previous patch for bug #4687 causes PEP8 regression problem,
by SASANO Takayoshi 30 Apr '17

30 Apr '17

# HG changeset patch # User SASANO Takayoshi <uaa(a)mx5.nisiq.net> # Date 1493583918 -32400 # Mon May 01 05:25:18 2017 +0900 # Node ID 709a6b83ea0f9241f9b7007afcb6bf21ea73dc3c # Parent 50a123640cf59047c2e8f91f4a87cb3e9380dfdb previous patch for bug #4687 causes PEP8 regression problem, "E261 at least two spaces before inline comment". Replace a tab character to two spaces to fix the problem. diff -r 50a123640cf5 -r 709a6b83ea0f chirp/drivers/icf.py --- a/chirp/drivers/icf.py Fri Apr 28 23:10:50 2017 +0900 +++ b/chirp/drivers/icf.py Mon May 01 05:25:18 2017 +0900 @@ -199,7 +199,7 @@ pipe.write(frame) pipe.flush() - pipe.read(len(frame)) # discard echoback + pipe.read(len(frame)) # discard echoback return frame @@ -263,7 +263,7 @@ LOG.debug("Starting HiSpeed Clone:\n%s" % util.hexprint(buf)) radio.pipe.write(buf) radio.pipe.flush() - radio.pipe.read(len(buf)) # discard echoback + radio.pipe.read(len(buf)) # discard echoback def _clone_from_radio(radio):

1 0

[chirp_devel] [PATCH] [VX-3] fix bank_used issue #1203
by Ray Cielencki 28 Apr '17

28 Apr '17

# HG changeset patch # User Ray Cielencki <rayslinky(a)gmail.com> # Date 1493420374 14400 # Fri Apr 28 18:59:34 2017 -0400 # Node ID 269ddc3236ca0971cbdc704ec52f193ef9092fb7 # Parent 7fe5f7b14be57479d4d37c9e204caf6a076b5d18 [VX-3] fix bank_used issue #1203 This patch works around #1203 -- where banks are not properly marked as used. Additionally, it corrects how bank_used values are calculated. diff -r 7fe5f7b14be5 -r 269ddc3236ca chirp/drivers/vx3.py --- a/chirp/drivers/vx3.py Thu Apr 13 17:31:54 2017 -0700 +++ b/chirp/drivers/vx3.py Fri Apr 28 18:59:34 2017 -0400 @@ -141,11 +141,18 @@ u8 banks_unk1; #seekto 0x0356; -u32 banks_unk2; +struct { + u32 unmask; +} banks_unmask1; #seekto 0x0409; u8 banks_unk3; +#seekto 0x0416; +struct { + u32 unmask; +} banks_unmask2; + #seekto 0x04CA; struct { u8 memory[16]; @@ -300,7 +307,11 @@ channels_in_bank.add(memory.number) self._update_bank_with_channel_numbers(bank, channels_in_bank) _bank_used = self._radio._memobj.bank_used[bank.index] - _bank_used.in_use = 0x0000 + _bank_used.in_use = ((len(channels_in_bank) - 1) * 2) + _banks_unmask1 = self._radio._memobj.banks_unmask1 + _banks_unmask2 = self._radio._memobj.banks_unmask2 + _banks_unmask1.unmask = 0x0017FFFF + _banks_unmask2.unmask = 0x0017FFFF def remove_memory_from_mapping(self, memory, bank): channels_in_bank = self._get_channel_numbers_in_bank(bank) @@ -311,8 +322,10 @@ (memory.number, bank)) self._update_bank_with_channel_numbers(bank, channels_in_bank) - if not channels_in_bank: - _bank_used = self._radio._memobj.bank_used[bank.index] + _bank_used = self._radio._memobj.bank_used[bank.index] + if channels_in_bank: + _bank_used.in_use = ((len(channels_in_bank) - 1) * 2) + else: _bank_used.in_use = 0xFFFF def get_mapping_memories(self, bank):

1 0

[chirp_devel] [PATCH] Bug#4771, add high-speed (38400bps) cloning to IC-P7
by SASANO Takayoshi 28 Apr '17

28 Apr '17

# HG changeset patch # User SASANO Takayoshi <uaa(a)mx5.nisiq.net> # Date 1493388650 -32400 # Fri Apr 28 23:10:50 2017 +0900 # Node ID 50a123640cf59047c2e8f91f4a87cb3e9380dfdb # Parent 83a16e525434395133159a5ef1095604a75082cb Bug#4771, add high-speed (38400bps) cloning to IC-P7 diff -r 83a16e525434 -r 50a123640cf5 chirp/drivers/icp7.py --- a/chirp/drivers/icp7.py Fri Apr 28 22:43:23 2017 +0900 +++ b/chirp/drivers/icp7.py Fri Apr 28 23:10:50 2017 +0900 @@ -98,6 +98,7 @@ _num_banks = 18 _bank_class = ICP7Bank + _can_hispeed = True def _get_bank(self, loc): _bank = self._memobj.banks[loc] @@ -131,6 +132,7 @@ rf.valid_skips = ["", "S", "P"] rf.valid_tuning_steps = TUNING_STEPS rf.valid_name_length = 6 + rf.has_settings = True rf.has_ctone = True rf.has_bank = True rf.has_bank_index = True

1 0

[chirp_devel] Noob, want to add a driver, getting started questions
by Stephanie Maks 28 Apr '17

28 Apr '17

Hi all, I'm new to Chirp, and looking to set up a driver for my favorite radio - the Yaesu FT-8000. I have lots of experience coding, and am familiar with Python. I have read the developer docs and I'm trying to follow the 'Using existing Chirp code' procedure, but running into a snag. I see there's a driver for the FT-8100, and it's my understanding that the 8100 was based on the 8000, with the main differences being the 8100 has twice as many memories, and a removable front panel. Using the 8100 driver, I can initiate a download from the FT-8000 but when the FT-8000 stops sending its data (it is sending less data than the 8100 driver expects) instead of giving me the option to save the 'incomplete' dump, the process just times out and fails, and the incomplete capture is lost. I can see the progress bar advances to about 75% then it stops, and then I get the error that the radio stopped responding and the download is gone. Contrary to the instructions in the 'Add a Radio' document, I never get the chance to save the image. Is there a toggle or setting I need to switch somewhere, or some code I need to change, that will let me save 'incomplete' reads rather than Chirp just dropping them after it times out? FWIW I am running on OSX 10.12.4 and using the latest version of Chirp, 20170420 at the moment. I can confirm that my set-up works fine on other radios; I have successfully used the same cable and Chirp to program a Yaesu FT-7900. Thank you! 73 de Stephanie va3uxb

2 2

[chirp_devel] [PATCH] Bug #4769
by SASANO Takayoshi 28 Apr '17

28 Apr '17

# HG changeset patch # User SASANO Takayoshi <uaa(a)mx5.nisiq.net> # Date 1493387003 -32400 # Fri Apr 28 22:43:23 2017 +0900 # Node ID 83a16e525434395133159a5ef1095604a75082cb # Parent 7fe5f7b14be57479d4d37c9e204caf6a076b5d18 Bug #4769 remove meaningless _mem.set_raw("\x00" * (_mem.size() / 8)) line, all elements are filled when setting/emptying entry. diff -r 7fe5f7b14be5 -r 83a16e525434 chirp/drivers/icp7.py --- a/chirp/drivers/icp7.py Thu Apr 13 17:31:54 2017 -0700 +++ b/chirp/drivers/icp7.py Fri Apr 28 22:43:23 2017 +0900 @@ -187,8 +187,6 @@ _skp = self._memobj.skips[byte] _psk = self._memobj.pskips[byte] - _mem.set_raw("\x00" * (_mem.size() / 8)) - if mem.empty: _usd |= bit

1 0

[chirp_devel] KG-UV9D Checksum
by dropkick23＠gmail.com 24 Apr '17

24 Apr '17

I have been looking at Wouxun KG-UV9D trying to determine the record checksum calculation. I have tried a couple of CRC-8 online calculators without success. I also used https://github.com/sitsec/bruteforce-crc on 223 memory records hoping to find one polynomial that worked for all records, best was 30 of 223. Examples: read request record sent to radio all have checksum of 0x38: 7D 84 FF 03 58 58 38 38 7D 84 FF 03 5C 5C 3C 38 7D 84 FF 03 10 50 30 38 7D 84 FF 03 11 51 31 38 7D 84 FF 03 14 54 34 38 7D 84 FF 03 15 55 35 38 Memory records last byte is checksum: 7D 84 00 62 58 18 E7 18 E7 18 E7 18 E7 18 E7 18 E7 18 E7 1A E5 1A E5 1A E5 1A E5 1A E5 1A E5 1A E5 1A E5 18 E7 18 E7 18 E7 18 E7 18 E7 18 E7 18 E7 18 E7 1A E5 1A E5 1A E5 1A E5 1A E5 1A E5 1A E5 1A E5 18 E7 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 10 7D 84 00 62 58 D8 27 D8 27 D8 27 D8 27 D8 27 D8 27 D8 27 DA 25 DA DA 22 2A 32 32 CA C2 DA DA DA DA DA 39 E9 15 EA EA 12 1A 02 02 FA F2 EA EA EA EA EA 09 D9 25 DA DA 22 2A 32 32 CA C2 DA DA DA DA DA 39 E9 15 EA EA EA EA EA EA EA EA EA BD D8 B9 CD A5 C0 B2 83 D4 B1 D0 A4 CC A9 DB E9 BE DB BA CE A6 C3 B1 83 8E 7D 84 00 62 58 98 98 60 68 70 70 88 80 98 98 98 98 98 7B AB 57 A8 A8 50 58 40 40 B8 B0 A8 A8 A8 A8 A8 4B 9B 67 98 98 60 68 70 70 88 80 98 98 98 98 98 7B AB 57 A8 A8 50 58 40 40 B8 B0 A8 A8 A8 A8 A8 4B 9B 67 98 CF AA CB BF D7 B2 C0 F4 A3 C6 A7 D3 BB DE AC 99 CE AB CA BE D6 B3 C1 F7 A0 C5 A4 D0 B8 DD AF 98 96 If the checksum calculation can be determined, I believe it will also apply to other Newer Wouxun radios KG-UV8D Plus is one example. It has a different checksum calculation than the KG-UV8D with is a simple (sum mod 0xff) I have been looking at this on and off for a few months now and feel I have reached a dead end on the checksum calculation. Any help would be welcomed. Fred dropkick23(a)gmail.com

1 0

[chirp_devel] [PATCH] [TK-270] Allow programming Kenwood commercial radios up to 10 MHz out of band. #4709
by Tom Hayward 24 Apr '17

24 Apr '17

# HG changeset patch # User Tom Hayward <tom(a)tomh.us> # Date 1492129341 25200 # Thu Apr 13 17:22:21 2017 -0700 # Node ID 791293b5a0101a7be61cafdc1b41cdd0a431cfd8 # Parent 0019ce490c8e92b4099393a4c83c3f4e3c11d10a [TK-270] Allow programming Kenwood commercial radios up to 10 MHz out of band. #4709 diff -r 0019ce490c8e -r 791293b5a010 chirp/drivers/tk270.py --- a/chirp/drivers/tk270.py Thu Apr 13 17:13:38 2017 -0700 +++ b/chirp/drivers/tk270.py Thu Apr 13 17:22:21 2017 -0700 @@ -413,17 +413,12 @@ # indentify the radio variant and set the enviroment to it's values try: self._upper, low, high, self._kind = self.VARIANTS[rid] - self._range = [low * 1000000, high * 1000000] + self._range = [(low - 10) * 1000000, (high + 10) * 1000000] # put the VARIANT in the class, clean the model / CHs / Type # in the same layout as the KPG program - self._VARIANT = self.MODEL + " [" + str(self._upper) + "CH]: " - self._VARIANT += self._kind + ", " - self._VARIANT += str(self._range[0]/1000000) + "-" - self._VARIANT += str(self._range[1]/1000000) + " Mhz" - - # DEBUG - #print self._VARIANT + self._VARIANT = "%s [%dCH]: %s, %d-%d Mhz" % ( + self.MODEL, self._upper, self._kind, low, high) except KeyError: LOG.debug("Wrong Kenwood radio, ID or unknown variant")

2 3

[chirp_devel] Fix to #4749
by Richard Birch 21 Apr '17

21 Apr '17

Here is the corrected patch to bug #4749. Previous patch fixed the problem, but for the wrong reason.

1 0