Developers

Download

developers@lists.chirpmyradio.com

3 participants
2972 discussions

[chirp_devel] Semantics of TSQL?
by Dan Clemmensen 20 Feb '19

20 Feb '19

Help, please. I cannot get this to work without a kludge. When the UI has a tone mode of "TSQL" and rtone and ctone are different, what is the radio supposed to do? My radio had has_ctone = True. The documentation is unclear. TSQL is documented to mean "send and receive the same tone. Use the tone in rtone if has_ctone==False. Use the tone in ctone if has_ctone==true. But the UI (in particular, the CopyAll test csv file) appears to imply that TSQL (ctone!=rtone) should cause transmit the rtone and unsquelch on the ctone.

2 1

[chirp_devel] Build test results: Failure
by Build System 19 Feb '19

19 Feb '19

Tested changes: Changes for Build #780 [Dan Smith <dsmith(a)danplanet.com>] Fix Edges::do_oddsteps() test This test was completely wrong, and not really running for any driver. Realized it was doing something stupid while trying to run it against the CSV driver (which supports DC->daylight). Some radios were claiming to support steps they don't support because they were taking the full list in chirp_common as a default, which is clearly wrong. This patch changes the default to a very conservative set, which may cause some drivers to no longer accept some frequencies that may be valid because they were not declaring their real supported list. This also uncovered at least one buggy driver that can't support anything other than 5kHz step frequencies (ic2730). Found in the pursuit of #495 [Tom Hayward <tom(a)tomh.us>] [id880] Fix typo in charset definition. #281 [Tom Hayward <tom(a)tomh.us>] [thf6a] Support full charset (ASCII). Fixes #141 [Tom Hayward <tom(a)tomh.us>] [id880] Support full charset. Fixes #281 [Tom Hayward <tom(a)tomh.us>] [vx5] Support full charset (ASCII). Fixes #292 [Tom Hayward <tom(a)tomh.us>] [id31a] set used bit when creating new memory, clear when deleting. Fixes #269 [Tom Hayward <tom(a)tomh.us>] Support PyGTK < 2.22 in bank edit. Fixes #231 [Tom Hayward <tom(a)tomh.us>] [d710] [v71] [d72] Fix tone list (not all tones are supported). Fixes #212 [Dan Smith <dsmith(a)danplanet.com>] [vx7] Fix setting memory power levels on 220MHz band Fixes #214 [Dan Smith <dsmith(a)danplanet.com>] fips: Pennsylvania FIPS code was wrong. #117 [Marco Filippi <iz3gme.marco(a)gmail.com>] Consider lower bound frequency of each valid_band as valid Fix bug #181 [Tom Hayward <tom(a)tomh.us>] tmd700: allow 8-char names. Fixes #176 [Dan Smith <dsmith(a)danplanet.com>] Fix the "blind deletion" problem, as well as properly direct copy/paste Fixes #172 [David Griffith <dave(a)661.org>] Bug #155 fix: VX-7 1.25m power levels [David Griffith <dave(a)661.org>] New INSTALL and README files Fixes #122 [Tom Hayward <tom(a)tomh.us>] thd72: only use hardware flow on OS X. Fixes #166 [Marco Filippi <iz3gme.marco(a)gmail.com>] [FT817] Tone freq not set correctly Same as #88 for FT857, to avoid code duplication fix code have been moved from ft857 to its ancestor class Fix bug #163 [Tom Hayward <tom(a)tomh.us>] Fix Mac .app so paths with spaces work. Fixes Bug #145 Full log: [...truncated 292 lines...] Testing BTECH MURS-V1 clone ... ok test_copy_all (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 copy all ... ok test_detect (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 detect ... ok test_edges (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 edges ... skipped 'No mutable memory locations found' test_settings (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 settings ... ok test_banks (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M brute force ... ok test_clone (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M clone ... ok test_copy_all (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M copy all ... ok test_detect (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M detect ... ok test_edges (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M edges ... ok test_settings (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 brute force ... ok test_clone (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 clone ... ok test_copy_all (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 copy all ... ok test_detect (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 detect ... ok test_edges (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 edges ... ok test_settings (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 settings ... ok test_banks (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 brute force ... ok test_clone (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 clone ... ok test_copy_all (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 copy all ... ok test_detect (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 detect ... ok test_edges (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 edges ... ok test_settings (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 settings ... ok test_banks (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 brute force ... ok test_clone (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 clone ... ok test_copy_all (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 copy all ... ok test_detect (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 detect ... ok test_edges (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 edges ... ok test_settings (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomID880H) Testing Icom ID-880H banks ... ok test_brute_force (tests.TestCase_IcomID880H) Testing Icom ID-880H brute force ... ok test_clone (tests.TestCase_IcomID880H) Testing Icom ID-880H clone ... ok test_copy_all (tests.TestCase_IcomID880H) Testing Icom ID-880H copy all ... ok test_detect (tests.TestCase_IcomID880H) Testing Icom ID-880H detect ... ok test_edges (tests.TestCase_IcomID880H) Testing Icom ID-880H edges ... ok test_settings (tests.TestCase_IcomID880H) Testing Icom ID-880H settings ... ok test_banks (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D banks ... ok test_brute_force (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D brute force ... ok test_clone (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D clone ... ok test_copy_all (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D copy all ... ok test_detect (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D detect ... ok test_edges (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D edges ... ok test_settings (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D settings ... ok test_banks (tests.TestCase_RetevisRT26) Testing Retevis RT26 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT26) Testing Retevis RT26 brute force ... ok test_clone (tests.TestCase_RetevisRT26) Testing Retevis RT26 clone ... ok test_copy_all (tests.TestCase_RetevisRT26) Testing Retevis RT26 copy all ... ok test_detect (tests.TestCase_RetevisRT26) Testing Retevis RT26 detect ... ok test_edges (tests.TestCase_RetevisRT26) Testing Retevis RT26 edges ... ok test_settings (tests.TestCase_RetevisRT26) Testing Retevis RT26 settings ... ok test_banks (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R brute force ... ok test_clone (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R clone ... ok test_copy_all (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R copy all ... ok test_detect (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R detect ... ok test_edges (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R edges ... ok test_settings (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R settings ... ok test_banks (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 brute force ... ok test_clone (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 clone ... ok test_copy_all (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 copy all ... ok test_detect (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 detect ... ok test_edges (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 edges ... ok test_settings (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 settings ... ok test_banks (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R brute force ... ok test_clone (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R clone ... ok test_copy_all (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R copy all ... ok test_detect (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R detect ... ok test_edges (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R edges ... ok test_settings (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND brute force ... ok test_clone (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND clone ... ok test_copy_all (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND copy all ... ok test_detect (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND detect ... ok test_edges (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND edges ... ok test_settings (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND settings ... ok test_banks (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H banks ... ok test_brute_force (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H brute force ... ok test_clone (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H clone ... ok test_copy_all (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H copy all ... ok test_detect (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H detect ... ok test_edges (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H edges ... ok test_settings (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H settings ... ok test_banks (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M brute force ... ok test_clone (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M clone ... ok test_copy_all (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M copy all ... ok test_detect (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M detect ... ok test_edges (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M edges ... ok test_settings (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 brute force ... ok test_clone (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 clone ... ok test_copy_all (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 copy all ... ok test_detect (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 detect ... ok test_edges (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 edges ... ok test_settings (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH brute force ... ok test_clone (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH clone ... ok test_copy_all (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH copy all ... ok test_detect (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH detect ... ok test_edges (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH edges ... ok test_settings (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH settings ... ok test_banks (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 brute force ... ok test_clone (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 clone ... ok test_copy_all (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 copy all ... ok test_detect (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 detect ... ok test_edges (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 edges ... ok test_settings (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 settings ... ok test_banks (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 brute force ... ok test_clone (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 clone ... ok test_copy_all (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 copy all ... ok test_detect (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 detect ... ok test_edges (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 edges ... ok test_settings (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 settings ... ok test_banks (tests.TestCase_IcomICT7H) Testing Icom IC-T7H banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICT7H) Testing Icom IC-T7H brute force ... ok test_clone (tests.TestCase_IcomICT7H) Testing Icom IC-T7H clone ... ok test_copy_all (tests.TestCase_IcomICT7H) Testing Icom IC-T7H copy all ... ok test_detect (tests.TestCase_IcomICT7H) Testing Icom IC-T7H detect ... ok test_edges (tests.TestCase_IcomICT7H) Testing Icom IC-T7H edges ... ok test_settings (tests.TestCase_IcomICT7H) Testing Icom IC-T7H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 brute force ... ok test_clone (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 clone ... ok test_copy_all (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 copy all ... ok test_detect (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 detect ... ok test_edges (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 edges ... ok test_settings (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H banks ... ok test_brute_force (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H brute force ... ok test_clone (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H clone ... ok test_copy_all (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H copy all ... ok test_detect (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H detect ... ok test_edges (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H edges ... ok test_settings (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H settings ... ok test_banks (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 banks ... ok test_brute_force (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 brute force ... ok test_clone (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 clone ... ok test_copy_all (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 copy all ... ok test_detect (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 detect ... ok test_edges (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 edges ... ok test_settings (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A brute force ... ok test_clone (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A clone ... ok test_copy_all (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A copy all ... ok test_detect (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A detect ... ok test_edges (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A edges ... ok test_settings (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A settings ... ok test_banks (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 brute force ... ok test_clone (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 clone ... ok test_copy_all (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 copy all ... ok test_detect (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 detect ... ok test_edges (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 edges ... ok test_settings (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 settings ... ok test_banks (tests.TestCase_TYTTH350) Testing TYT TH-350 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTH350) Testing TYT TH-350 brute force ... ok test_clone (tests.TestCase_TYTTH350) Testing TYT TH-350 clone ... ok test_copy_all (tests.TestCase_TYTTH350) Testing TYT TH-350 copy all ... ok test_detect (tests.TestCase_TYTTH350) Testing TYT TH-350 detect ... ok test_edges (tests.TestCase_TYTTH350) Testing TYT TH-350 edges ... ok test_settings (tests.TestCase_TYTTH350) Testing TYT TH-350 settings ... ok test_banks (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 brute force ... ok test_clone (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 clone ... ok test_copy_all (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 copy all ... ok test_detect (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 detect ... ok test_edges (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 edges ... ok test_settings (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 settings ... ok test_banks (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R brute force ... ok test_clone (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R clone ... ok test_copy_all (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R copy all ... ok test_detect (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R detect ... ok test_edges (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R edges ... ok test_settings (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R settings ... ok test_banks (tests.TestCase_RadioddityR2) Testing Radioddity R2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RadioddityR2) Testing Radioddity R2 brute force ... ok test_clone (tests.TestCase_RadioddityR2) Testing Radioddity R2 clone ... ok test_copy_all (tests.TestCase_RadioddityR2) Testing Radioddity R2 copy all ... ok test_detect (tests.TestCase_RadioddityR2) Testing Radioddity R2 detect ... ok test_edges (tests.TestCase_RadioddityR2) Testing Radioddity R2 edges ... ok test_settings (tests.TestCase_RadioddityR2) Testing Radioddity R2 settings ... ok test_banks (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R brute force ... ok test_clone (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R clone ... ok test_copy_all (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R copy all ... ok test_detect (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R detect ... ok test_edges (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R edges ... ok test_settings (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R settings ... ok test_banks (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 brute force ... ok test_clone (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 clone ... ok test_copy_all (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 copy all ... ok test_detect (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 detect ... ok test_edges (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 edges ... ok test_settings (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 settings ... ok test_banks (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M brute force ... ok test_clone (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M clone ... ok test_copy_all (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M copy all ... ok test_detect (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M detect ... ok test_edges (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M edges ... ok test_settings (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M settings ... ok test_banks (tests.TestCase_IcomICP7) Testing Icom IC-P7 banks ... ok test_brute_force (tests.TestCase_IcomICP7) Testing Icom IC-P7 brute force ... ok test_clone (tests.TestCase_IcomICP7) Testing Icom IC-P7 clone ... ok test_copy_all (tests.TestCase_IcomICP7) Testing Icom IC-P7 copy all ... ok test_detect (tests.TestCase_IcomICP7) Testing Icom IC-P7 detect ... ok test_edges (tests.TestCase_IcomICP7) Testing Icom IC-P7 edges ... ok test_settings (tests.TestCase_IcomICP7) Testing Icom IC-P7 settings ... ok test_banks (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus brute force ... ok test_clone (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus clone ... ok test_copy_all (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus copy all ... ok test_detect (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus detect ... ok test_edges (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus edges ... ok test_settings (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus settings ... ok test_banks (tests.TestCase_IcomICW32E) Testing Icom IC-W32E banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICW32E) Testing Icom IC-W32E brute force ... ok test_clone (tests.TestCase_IcomICW32E) Testing Icom IC-W32E clone ... ok test_copy_all (tests.TestCase_IcomICW32E) Testing Icom IC-W32E copy all ... ok test_detect (tests.TestCase_IcomICW32E) Testing Icom IC-W32E detect ... ok test_edges (tests.TestCase_IcomICW32E) Testing Icom IC-W32E edges ... ok test_settings (tests.TestCase_IcomICW32E) Testing Icom IC-W32E settings ... skipped 'Settings not supported' test_banks (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M brute force ... ok test_clone (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M clone ... ok test_copy_all (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M copy all ... ok test_detect (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M detect ... ok test_edges (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M edges ... ok test_settings (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M settings ... ok test_banks (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 brute force ... ok test_clone (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 clone ... ok test_copy_all (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 copy all ... ok test_detect (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 detect ... ok test_edges (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 edges ... ok test_settings (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 brute force ... ok test_clone (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 clone ... ok test_copy_all (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 copy all ... ok test_detect (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 detect ... ok test_edges (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 edges ... ok test_settings (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 settings ... ok test_banks (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 brute force ... ok test_clone (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 clone ... ok test_copy_all (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 copy all ... ok test_detect (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 detect ... ok test_edges (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 edges ... ok test_settings (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 settings ... ok test_banks (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D banks ... ok test_brute_force (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D brute force ... ok test_clone (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D clone ... ok test_copy_all (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D copy all ... ok test_detect (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D detect ... ok test_edges (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D edges ... ok test_settings (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D settings ... ok test_banks (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) brute force ... ok test_clone (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) clone ... ok test_copy_all (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) copy all ... ok test_detect (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) detect ... ok test_edges (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) edges ... ok test_settings (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) settings ... ok test_banks (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D brute force ... ok test_clone (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D clone ... ok test_copy_all (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D copy all ... ok test_detect (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D detect ... ok test_edges (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D edges ... ok test_settings (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 banks ... ok test_brute_force (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 brute force ... ok test_clone (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 clone ... ok test_copy_all (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 copy all ... ok test_detect (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 detect ... ok test_edges (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 edges ... ok test_settings (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 settings ... ok test_banks (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H brute force ... ok test_clone (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H clone ... ok test_copy_all (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H copy all ... ok test_detect (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H detect ... ok test_edges (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H edges ... ok test_settings (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 brute force ... ok test_clone (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 clone ... ok test_copy_all (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 copy all ... ok test_detect (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 detect ... ok test_edges (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 edges ... ok test_settings (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_LeixenVV898) Testing Leixen VV-898 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_LeixenVV898) Testing Leixen VV-898 brute force ... ok test_clone (tests.TestCase_LeixenVV898) Testing Leixen VV-898 clone ... ok test_copy_all (tests.TestCase_LeixenVV898) Testing Leixen VV-898 copy all ... ok test_detect (tests.TestCase_LeixenVV898) Testing Leixen VV-898 detect ... ok test_edges (tests.TestCase_LeixenVV898) Testing Leixen VV-898 edges ... ok test_settings (tests.TestCase_LeixenVV898) Testing Leixen VV-898 settings ... ok test_banks (tests.TestCase_QYTKT7900D) Testing QYT KT7900D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_QYTKT7900D) Testing QYT KT7900D brute force ... ok test_clone (tests.TestCase_QYTKT7900D) Testing QYT KT7900D clone ... ok test_copy_all (tests.TestCase_QYTKT7900D) Testing QYT KT7900D copy all ... ok test_detect (tests.TestCase_QYTKT7900D) Testing QYT KT7900D detect ... ok test_edges (tests.TestCase_QYTKT7900D) Testing QYT KT7900D edges ... ok test_settings (tests.TestCase_QYTKT7900D) Testing QYT KT7900D settings ... ok test_banks (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P brute force ... ok test_clone (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P clone ... ok test_copy_all (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P copy all ... ok test_detect (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P detect ... ok test_edges (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P edges ... ok test_settings (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P settings ... ok test_banks (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 banks ... ok test_brute_force (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 brute force ... ok test_clone (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 clone ... ok test_copy_all (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 copy all ... ok test_detect (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 detect ... ok test_edges (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 edges ... ok test_settings (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomICW32A) Testing Icom IC-W32A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICW32A) Testing Icom IC-W32A brute force ... ok test_clone (tests.TestCase_IcomICW32A) Testing Icom IC-W32A clone ... ok test_copy_all (tests.TestCase_IcomICW32A) Testing Icom IC-W32A copy all ... ok test_detect (tests.TestCase_IcomICW32A) Testing Icom IC-W32A detect ... ok test_edges (tests.TestCase_IcomICW32A) Testing Icom IC-W32A edges ... ok test_settings (tests.TestCase_IcomICW32A) Testing Icom IC-W32A settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 banks ... ok test_brute_force (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 brute force ... ok test_clone (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 clone ... ok test_copy_all (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 copy all ... ok test_detect (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 detect ... ok test_edges (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 edges ... ok test_settings (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 settings ... ok test_banks (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B brute force ... ok test_clone (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B clone ... ok test_copy_all (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B copy all ... ok test_detect (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B detect ... ok test_edges (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B edges ... ok test_settings (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B settings ... ok test_banks (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R brute force ... ok test_clone (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R clone ... ok test_copy_all (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R copy all ... ok test_detect (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R detect ... ok test_edges (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R edges ... ok test_settings (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R settings ... ok test_banks (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 brute force ... ok test_clone (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 clone ... ok test_copy_all (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 copy all ... ok test_detect (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 detect ... ok test_edges (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 edges ... ok test_settings (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 settings ... ok test_banks (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 brute force ... ok test_clone (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 clone ... ok test_copy_all (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 copy all ... ok test_detect (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 detect ... ok test_edges (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 edges ... ok test_settings (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 settings ... ok test_banks (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV brute force ... ok test_clone (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV clone ... ok test_copy_all (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV copy all ... ok test_detect (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV detect ... ok test_edges (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV edges ... ok test_settings (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV settings ... ok test_banks (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 brute force ... ok test_clone (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 clone ... ok test_copy_all (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 copy all ... ok test_detect (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 detect ... ok test_edges (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 edges ... ok test_settings (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 settings ... ok test_banks (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M brute force ... ok test_clone (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M clone ... ok test_copy_all (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M copy all ... ok test_detect (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M detect ... ok test_edges (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M edges ... ok test_settings (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M settings ... ok test_banks (tests.TestCase_KYDNC630A) Testing KYD NC-630A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KYDNC630A) Testing KYD NC-630A brute force ... ok test_clone (tests.TestCase_KYDNC630A) Testing KYD NC-630A clone ... ok test_copy_all (tests.TestCase_KYDNC630A) Testing KYD NC-630A copy all ... ok test_detect (tests.TestCase_KYDNC630A) Testing KYD NC-630A detect ... ok test_edges (tests.TestCase_KYDNC630A) Testing KYD NC-630A edges ... ok test_settings (tests.TestCase_KYDNC630A) Testing KYD NC-630A settings ... ok test_banks (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 brute force ... ok test_clone (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 clone ... ok test_copy_all (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 copy all ... ok test_detect (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 detect ... ok test_edges (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 edges ... ok test_settings (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 settings ... ok test_banks (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 brute force ... ok test_clone (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 clone ... ok test_copy_all (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 copy all ... ok test_detect (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 detect ... ok test_edges (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 edges ... ok test_settings (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 settings ... ok test_banks (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 brute force ... ok test_clone (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 clone ... ok test_copy_all (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 copy all ... ok test_detect (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 detect ... ok test_edges (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 edges ... ok test_settings (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M brute force ... ok test_clone (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M clone ... ok test_copy_all (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M copy all ... ok test_detect (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M detect ... ok test_edges (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M edges ... ok test_settings (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H banks ... ok test_brute_force (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H brute force ... ok test_clone (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H clone ... ok test_copy_all (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H copy all ... ok test_detect (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H detect ... ok test_edges (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H edges ... ok test_settings (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 brute force ... ok test_clone (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 clone ... ok test_copy_all (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 copy all ... ok test_detect (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 detect ... ok test_edges (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 edges ... ok test_settings (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 settings ... ok test_banks (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 brute force ... ok test_clone (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 clone ... ok test_copy_all (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 copy all ... ok test_detect (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 detect ... ok test_edges (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 edges ... ok test_settings (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 settings ... ok test_banks (tests.TestCase_IcomID51) Testing Icom ID-51 banks ... ok test_brute_force (tests.TestCase_IcomID51) Testing Icom ID-51 brute force ... ok test_clone (tests.TestCase_IcomID51) Testing Icom ID-51 clone ... ok test_copy_all (tests.TestCase_IcomID51) Testing Icom ID-51 copy all ... ok test_detect (tests.TestCase_IcomID51) Testing Icom ID-51 detect ... ok test_edges (tests.TestCase_IcomID51) Testing Icom ID-51 edges ... ok test_settings (tests.TestCase_IcomID51) Testing Icom ID-51 settings ... ok test_banks (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) brute force ... ok test_clone (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) clone ... ok test_copy_all (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) copy all ... ok test_detect (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) detect ... ok test_edges (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) edges ... ok test_settings (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) settings ... ok test_banks (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR banks ... ok test_brute_force (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR brute force ... ok test_clone (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR clone ... ok test_copy_all (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR copy all ... ok test_detect (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR detect ... ok test_edges (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR edges ... ok test_settings (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR settings ... ok test_banks (tests.TestCase_RadtelT18) Testing Radtel T18 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RadtelT18) Testing Radtel T18 brute force ... ok test_clone (tests.TestCase_RadtelT18) Testing Radtel T18 clone ... ok test_copy_all (tests.TestCase_RadtelT18) Testing Radtel T18 copy all ... ok test_detect (tests.TestCase_RadtelT18) Testing Radtel T18 detect ... ok test_edges (tests.TestCase_RadtelT18) Testing Radtel T18 edges ... ok test_settings (tests.TestCase_RadtelT18) Testing Radtel T18 settings ... ok test_banks (tests.TestCase_BaofengF11) Testing Baofeng F-11 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengF11) Testing Baofeng F-11 brute force ... ok test_clone (tests.TestCase_BaofengF11) Testing Baofeng F-11 clone ... ok test_copy_all (tests.TestCase_BaofengF11) Testing Baofeng F-11 copy all ... ok test_detect (tests.TestCase_BaofengF11) Testing Baofeng F-11 detect ... ok test_edges (tests.TestCase_BaofengF11) Testing Baofeng F-11 edges ... ok test_settings (tests.TestCase_BaofengF11) Testing Baofeng F-11 settings ... ok test_banks (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A brute force ... ok test_clone (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A clone ... ok test_copy_all (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A copy all ... ok test_detect (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A detect ... ok test_edges (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A edges ... ok test_settings (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A settings ... ok test_banks (tests.TestCase_AlincoDJ175) Testing Alinco DJ175 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AlincoDJ175) Testing Alinco DJ175 brute force ... ok test_clone (tests.TestCase_AlincoDJ175) Testing Alinco DJ175 clone ... ok test_copy_all (tests.TestCase_AlincoDJ175) Testing Alinco DJ175 copy all ... ok test_detect (tests.TestCase_AlincoDJ175) Testing Alinco DJ175 detect ... ok test_edges (tests.TestCase_AlincoDJ175) Testing Alinco DJ175 edges ... ok test_settings (tests.TestCase_AlincoDJ175) Testing Alinco DJ175 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 brute force ... ok test_clone (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 clone ... ok test_copy_all (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 copy all ... ok test_detect (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 detect ... ok test_edges (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 edges ... ok test_settings (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 settings ... ok test_banks (tests.TestCase_RetevisRT22) Testing Retevis RT22 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT22) Testing Retevis RT22 brute force ... ok test_clone (tests.TestCase_RetevisRT22) Testing Retevis RT22 clone ... ok test_copy_all (tests.TestCase_RetevisRT22) Testing Retevis RT22 copy all ... ok test_detect (tests.TestCase_RetevisRT22) Testing Retevis RT22 detect ... ok test_edges (tests.TestCase_RetevisRT22) Testing Retevis RT22 edges ... ok test_settings (tests.TestCase_RetevisRT22) Testing Retevis RT22 settings ... ok test_banks (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R banks ... ok test_brute_force (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R brute force ... ok test_clone (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R clone ... ok test_copy_all (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R copy all ... ok test_detect (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R detect ... ok test_edges (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R edges ... ok test_settings (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R settings ... ok test_banks (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG brute force ... ok test_clone (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG clone ... ok test_copy_all (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG copy all ... ok test_detect (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG detect ... ok test_edges (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG edges ... ok test_settings (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG settings ... skipped 'Settings not supported' test_banks (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S brute force ... ok test_clone (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S clone ... ok test_copy_all (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S copy all ... ok test_detect (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S detect ... ok test_edges (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S edges ... ok test_settings (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S settings ... ok test_banks (tests.TestCase_KYDIP620) Testing KYD IP-620 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KYDIP620) Testing KYD IP-620 brute force ... ok test_clone (tests.TestCase_KYDIP620) Testing KYD IP-620 clone ... ok test_copy_all (tests.TestCase_KYDIP620) Testing KYD IP-620 copy all ... ok test_detect (tests.TestCase_KYDIP620) Testing KYD IP-620 detect ... ok test_edges (tests.TestCase_KYDIP620) Testing KYD IP-620 edges ... ok test_settings (tests.TestCase_KYDIP620) Testing KYD IP-620 settings ... ok test_banks (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 banks ... ok test_brute_force (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 brute force ... ok test_clone (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 clone ... ok test_copy_all (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 copy all ... ok test_detect (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 detect ... ok test_edges (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 edges ... ok test_settings (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 settings ... ok test_banks (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 banks ... ok test_brute_force (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 brute force ... ok test_clone (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 clone ... ok test_copy_all (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 copy all ... ok test_detect (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 detect ... ok test_edges (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 edges ... ok test_settings (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 settings ... ok test_banks (tests.TestCase_WouxunKGUV8DPlus) Testing Wouxun KG-UV8D Plus banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUV8DPlus) Testing Wouxun KG-UV8D Plus brute force ... ok test_clone (tests.TestCase_WouxunKGUV8DPlus) Testing Wouxun KG-UV8D Plus clone ... ok test_copy_all (tests.TestCase_WouxunKGUV8DPlus) Testing Wouxun KG-UV8D Plus copy all ... ok test_detect (tests.TestCase_WouxunKGUV8DPlus) Testing Wouxun KG-UV8D Plus detect ... ok test_edges (tests.TestCase_WouxunKGUV8DPlus) Testing Wouxun KG-UV8D Plus edges ... ok test_settings (tests.TestCase_WouxunKGUV8DPlus) Testing Wouxun KG-UV8D Plus settings ... ok test_banks (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D brute force ... ok test_clone (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D clone ... ok test_copy_all (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D copy all ... ok test_detect (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D detect ... ok test_edges (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D edges ... ok test_settings (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D settings ... ok test_banks (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G banks ... ok test_brute_force (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G brute force ... ok test_clone (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G clone ... ok test_copy_all (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G copy all ... ok test_detect (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G detect ... ok test_edges (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G edges ... ok test_settings (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G settings ... ok test_banks (tests.TestCase_QYTKT8900D) Testing QYT KT8900D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_QYTKT8900D) Testing QYT KT8900D brute force ... ok test_clone (tests.TestCase_QYTKT8900D) Testing QYT KT8900D clone ... ok test_copy_all (tests.TestCase_QYTKT8900D) Testing QYT KT8900D copy all ... ok test_detect (tests.TestCase_QYTKT8900D) Testing QYT KT8900D detect ... ok test_edges (tests.TestCase_QYTKT8900D) Testing QYT KT8900D edges ... ok test_settings (tests.TestCase_QYTKT8900D) Testing QYT KT8900D settings ... ok test_banks (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G banks ... ok test_brute_force (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G brute force ... ok test_clone (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G clone ... ok test_copy_all (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G copy all ... ok test_detect (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G detect ... ok test_edges (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G edges ... ok test_settings (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G settings ... ok test_banks (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 banks ... ok test_brute_force (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 brute force ... ok test_clone (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 clone ... ok test_copy_all (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 copy all ... ok test_detect (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 detect ... ok test_edges (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 edges ... ok test_settings (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomIC208H) Testing Icom IC-208H banks ... ok test_brute_force (tests.TestCase_IcomIC208H) Testing Icom IC-208H brute force ... ok test_clone (tests.TestCase_IcomIC208H) Testing Icom IC-208H clone ... ok test_copy_all (tests.TestCase_IcomIC208H) Testing Icom IC-208H copy all ... ok test_detect (tests.TestCase_IcomIC208H) Testing Icom IC-208H detect ... ok test_edges (tests.TestCase_IcomIC208H) Testing Icom IC-208H edges ... ok test_settings (tests.TestCase_IcomIC208H) Testing Icom IC-208H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomID31A) Testing Icom ID-31A banks ... ok test_brute_force (tests.TestCase_IcomID31A) Testing Icom ID-31A brute force ... ok test_clone (tests.TestCase_IcomID31A) Testing Icom ID-31A clone ... ok test_copy_all (tests.TestCase_IcomID31A) Testing Icom ID-31A copy all ... ok test_detect (tests.TestCase_IcomID31A) Testing Icom ID-31A detect ... ok test_edges (tests.TestCase_IcomID31A) Testing Icom ID-31A edges ... ok test_settings (tests.TestCase_IcomID31A) Testing Icom ID-31A settings ... ok test_banks (tests.TestCase_TYTTH7800) Testing TYT TH-7800 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTH7800) Testing TYT TH-7800 brute force ... ok test_clone (tests.TestCase_TYTTH7800) Testing TYT TH-7800 clone ... ok test_copy_all (tests.TestCase_TYTTH7800) Testing TYT TH-7800 copy all ... ok test_detect (tests.TestCase_TYTTH7800) Testing TYT TH-7800 detect ... ok test_edges (tests.TestCase_TYTTH7800) Testing TYT TH-7800 edges ... ok test_settings (tests.TestCase_TYTTH7800) Testing TYT TH-7800 settings ... ok test_banks (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H banks ... ok test_brute_force (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H brute force ... ok test_clone (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H clone ... ok test_copy_all (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H copy all ... ok test_detect (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H detect ... ok test_edges (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H edges ... ok test_settings (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H settings ... ok test_banks (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K brute force ... ok test_clone (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K clone ... ok test_copy_all (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K copy all ... ok test_detect (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K detect ... ok test_edges (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K edges ... ok test_settings (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K settings ... ok test_banks (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 brute force ... ok test_clone (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 clone ... ok test_copy_all (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 copy all ... ok test_detect (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 detect ... ok test_edges (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 edges ... ok test_settings (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 settings ... ok test_banks (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A banks ... ok test_brute_force (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A brute force ... ok test_clone (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A clone ... ok test_copy_all (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A copy all ... ok test_detect (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A detect ... ok test_edges (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A edges ... ERROR test_settings (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A settings ... ok test_banks (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R brute force ... ok test_clone (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R clone ... ok test_copy_all (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R copy all ... ok test_detect (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R detect ... ok test_edges (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R edges ... ok test_settings (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R settings ... ok test_banks (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 brute force ... ok test_clone (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 clone ... ok test_copy_all (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 copy all ... ok test_detect (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 detect ... ok test_edges (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 edges ... ok test_settings (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 settings ... ok test_banks (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 banks ... ok test_brute_force (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 brute force ... ok test_clone (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 clone ... ok test_copy_all (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 copy all ... ok test_detect (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 detect ... ok test_edges (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 edges ... ok test_settings (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A brute force ... ok test_clone (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A clone ... ok test_copy_all (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A copy all ... ok test_detect (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A detect ... ok test_edges (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A edges ... ok test_settings (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A settings ... ok test_banks (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE banks ... ok test_brute_force (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE brute force ... ok test_clone (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE clone ... ok test_copy_all (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE copy all ... ok test_detect (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE detect ... ok test_edges (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE edges ... ok test_settings (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE settings ... ok test_banks (tests.TestCase_IcomICT70) Testing Icom IC-T70 banks ... ok test_brute_force (tests.TestCase_IcomICT70) Testing Icom IC-T70 brute force ... ok test_clone (tests.TestCase_IcomICT70) Testing Icom IC-T70 clone ... ok test_copy_all (tests.TestCase_IcomICT70) Testing Icom IC-T70 copy all ... ok test_detect (tests.TestCase_IcomICT70) Testing Icom IC-T70 detect ... ok test_edges (tests.TestCase_IcomICT70) Testing Icom IC-T70 edges ... ok test_settings (tests.TestCase_IcomICT70) Testing Icom IC-T70 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R brute force ... ok test_clone (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R clone ... ok test_copy_all (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R copy all ... ok test_detect (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R detect ... ok test_edges (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R edges ... ok test_settings (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D banks ... ok test_brute_force (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D brute force ... ok test_clone (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D clone ... ok test_copy_all (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D copy all ... ok test_detect (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D detect ... ok test_edges (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D edges ... ok test_settings (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D settings ... ok test_banks (tests.TestCase_RetevisRT23) Testing Retevis RT23 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT23) Testing Retevis RT23 brute force ... ok test_clone (tests.TestCase_RetevisRT23) Testing Retevis RT23 clone ... ok test_copy_all (tests.TestCase_RetevisRT23) Testing Retevis RT23 copy all ... ok test_detect (tests.TestCase_RetevisRT23) Testing Retevis RT23 detect ... ok test_edges (tests.TestCase_RetevisRT23) Testing Retevis RT23 edges ... ok test_settings (tests.TestCase_RetevisRT23) Testing Retevis RT23 settings ... ok test_banks (tests.TestCase_PuxingPX777) Testing Puxing PX-777 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_PuxingPX777) Testing Puxing PX-777 brute force ... ok test_clone (tests.TestCase_PuxingPX777) Testing Puxing PX-777 clone ... ok test_copy_all (tests.TestCase_PuxingPX777) Testing Puxing PX-777 copy all ... ok test_detect (tests.TestCase_PuxingPX777) Testing Puxing PX-777 detect ... ok test_edges (tests.TestCase_PuxingPX777) Testing Puxing PX-777 edges ... ok test_settings (tests.TestCase_PuxingPX777) Testing Puxing PX-777 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomID800H) Testing Icom ID-800H banks ... ok test_brute_force (tests.TestCase_IcomID800H) Testing Icom ID-800H brute force ... ok test_clone (tests.TestCase_IcomID800H) Testing Icom ID-800H clone ... ok test_copy_all (tests.TestCase_IcomID800H) Testing Icom ID-800H copy all ... ok test_detect (tests.TestCase_IcomID800H) Testing Icom ID-800H detect ... ok test_edges (tests.TestCase_IcomID800H) Testing Icom ID-800H edges ... ok test_settings (tests.TestCase_IcomID800H) Testing Icom ID-800H settings ... ok test_banks (tests.TestCase_AlincoDR235T) Testing Alinco DR235T banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AlincoDR235T) Testing Alinco DR235T brute force ... ok test_clone (tests.TestCase_AlincoDR235T) Testing Alinco DR235T clone ... ok test_copy_all (tests.TestCase_AlincoDR235T) Testing Alinco DR235T copy all ... ok test_detect (tests.TestCase_AlincoDR235T) Testing Alinco DR235T detect ... ok test_edges (tests.TestCase_AlincoDR235T) Testing Alinco DR235T edges ... ok test_settings (tests.TestCase_AlincoDR235T) Testing Alinco DR235T settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D brute force ... ok test_clone (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D clone ... ok test_copy_all (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D copy all ... ok test_detect (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D detect ... ok test_edges (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D edges ... ok test_settings (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D settings ... ok test_banks (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 banks ... ok test_brute_force (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 brute force ... ok test_clone (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 clone ... ok test_copy_all (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 copy all ... ok test_detect (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 detect ... ok test_edges (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 edges ... ok test_settings (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus brute force ... ok test_clone (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus clone ... ok test_copy_all (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus copy all ... ok test_detect (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus detect ... ok test_edges (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus edges ... ok test_settings (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus settings ... ok test_banks (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B brute force ... ok test_clone (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B clone ... ok test_copy_all (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B copy all ... ok test_detect (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B detect ... ok test_edges (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B edges ... ok test_settings (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B settings ... ok test_banks (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R banks ... ok test_brute_force (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R brute force ... ok test_clone (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R clone ... ok test_copy_all (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R copy all ... ok test_detect (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R detect ... ok test_edges (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R edges ... ok test_settings (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R settings ... ok test_banks (tests.TestCase_RetevisRT21) Testing Retevis RT21 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT21) Testing Retevis RT21 brute force ... ok test_clone (tests.TestCase_RetevisRT21) Testing Retevis RT21 clone ... ok test_copy_all (tests.TestCase_RetevisRT21) Testing Retevis RT21 copy all ... ok test_detect (tests.TestCase_RetevisRT21) Testing Retevis RT21 detect ... ok test_edges (tests.TestCase_RetevisRT21) Testing Retevis RT21 edges ... ok test_settings (tests.TestCase_RetevisRT21) Testing Retevis RT21 settings ... ok test_banks (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) brute force ... ok test_clone (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) clone ... ok test_copy_all (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) copy all ... ok test_detect (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) detect ... ok test_edges (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) edges ... ok test_settings (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) settings ... ok ====================================================================== ERROR: test_edges (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A edges ---------------------------------------------------------------------- Traceback (most recent call last): File "tests/__init__.py", line 53, in test_edges self._runtest(run_tests.TestCaseEdges) File "tests/__init__.py", line 40, in _runtest testcase.run() File "tests/run_tests.py", line 625, in run self.do_oddsteps(rf) File "tests/run_tests.py", line 580, in do_oddsteps self.compare_mem(m, n, ignore=['tuning_step']) File "tests/run_tests.py", line 248, in compare_mem raise TestFailedError(msg, details) TestFailedError: Field `freq' is `145855000', expected `145856250' ---------------------------------------------------------------------- Ran 819 tests in 217.929s FAILED (errors=1, skipped=116) ERROR: InvocationError for command '/chirp/.tox/driver/bin/python -munittest -vb tests' (exited with code 1) style create: /chirp/.tox/style style installdeps: pep8==1.6.2 style inst: /chirp/.tox/.tmp/package/1/chirp-0.3.0dev.zip style installed: DEPRECATION: Python 2.7 will reach the end of its life on January 1st, 2020. Please upgrade your Python as Python 2.7 won't be maintained after that date. A future version of pip will drop support for Python 2.7.,chirp==0.3.0.dev0,filelock==3.0.10,Mako==1.0.3,MarkupSafe==0.23,mercurial==3.7.3,pep8==1.6.2,pluggy==0.8.1,py==1.7.0,pygobject==3.20.0,pyserial==3.0.1,six==1.12.0,toml==0.10.0,tox==3.7.0,virtualenv==16.4.0 style run-test-pre: PYTHONHASHSEED='1266642300' style runtests: commands[0] | python ./tools/cpep8.py ___________________________________ summary ____________________________________ unit: commands succeeded ERROR: driver: commands failed style: commands succeeded Build step 'Execute shell' marked build as failure Email was triggered for: Failure Sending email for trigger: Failure

1 5

[chirp_devel] [PATCH] [ic2730] Support frequencies requiring a tuning step of 6.25 kHz. Fixes #6457
by Rhett Robinson 19 Feb '19

19 Feb '19

# HG changeset patch # User Rhett Robinson <rrhett(a)gmail.com> # Date 1550534826 28800 # Mon Feb 18 16:07:06 2019 -0800 # Node ID 90b4b9e47859a9623d4861f7f1021ba40d870eb2 # Parent b4e8134947c6447fb464d9de662dfc729affde9f [ic2730] Support frequencies requiring a tuning step of 6.25 kHz. Fixes #6457 This radio stores some flags indicating the tuning step of the frequency, and the frequency as a multiple of the tuning step. This patch adds support for a frequency that is a multiple of 6.25 kHz for both the frequency and offset. Still missing is support for a multiple of 25/3 kHz. diff -r b4e8134947c6 -r 90b4b9e47859 chirp/drivers/ic2730.py --- a/chirp/drivers/ic2730.py Sun Feb 17 20:30:59 2019 -0800 +++ b/chirp/drivers/ic2730.py Mon Feb 18 16:07:06 2019 -0800 @@ -25,11 +25,12 @@ # - weather channel alert MEM_FORMAT = """ struct { - u24 freq; + u24 freq_flags:6 + freq:18; u16 offset; u8 tune_step:4, - unknown5:3, - mode:1; + unknown5:2, + mode:2; u8 unknown6:2, rtone:6; u8 unknown7:2, @@ -86,7 +87,7 @@ TMODES = ["", "Tone", "??0", "TSQL", "??1", "DTCS", "TSQL-R", "DTCS-R", "DTC.OFF", "TON.DTC", "DTC.TSQ", "TON.TSQ"] DUPLEX = ["", "-", "+"] -MODES = ["FM", "NFM"] +MODES = ["FM", "NFM", "AM", "NAM"] DTCSP = ["NN", "NR", "RN", "RR"] AUTOREPEATER = ["OFF", "DUP", "DUP.TON"] @@ -209,9 +210,19 @@ mem.empty = True return mem - # Frequencies are stored as kHz/5 - mem.freq = int(_mem.freq) * 5000 - mem.offset = int(_mem.offset) * 5000 + # _mem.freq is stored as a multiple of a tuning step + frequency_flags = int(_mem.freq_flags) + frequency_multiplier = 5000 + offset_multiplier = 5000 + if frequency_flags & 0x08: + frequency_multiplier = 6250 + if frequency_flags & 0x01: + offset_multiplier = 6250 + # flag of 0x10 is related to tuning step of 25./3, but it is not exact, + # so skip this for now + + mem.freq = int(_mem.freq) * frequency_multiplier + mem.offset = int(_mem.offset) * offset_multiplier mem.rtone = chirp_common.TONES[_mem.rtone] mem.ctone = chirp_common.TONES[_mem.ctone] mem.tmode = TMODES[_mem.tmode] @@ -257,8 +268,18 @@ if was_empty: _wipe_memory(_mem, "\x00") - _mem.freq = mem.freq / 5000 - _mem.offset = mem.offset / 5000 + frequency_flags = 0x00 + frequency_multiplier = 5000 + offset_multiplier = 5000 + if mem.freq % 5000 != 0 and mem.freq % 6250 == 0: + frequency_flags |= 0x08 + frequency_multiplier = 6250 + if mem.offset % 5000 != 0 and mem.offset % 6250 == 0: + frequency_flags |= 0x01 + offset_multiplier = 6250 + _mem.freq = mem.freq / frequency_multiplier + _mem.offset = mem.offset / offset_multiplier + _mem.freq_flags = frequency_flags _mem.rtone = chirp_common.TONES.index(mem.rtone) _mem.ctone = chirp_common.TONES.index(mem.ctone) _mem.tmode = TMODES.index(mem.tmode)

1 0

[chirp_devel] New driver for FT-4 and FT-65 #4787
by Dan Clemmensen 18 Feb '19

18 Feb '19

I cannot figure out how to submit an entirely new driver, so Its here as an attachment, along with the .img file. This driver runs and passes the pep and tox tests on both Python 2 and Python 3. I am of course clueless about any python 2 and Python3 subtleties . There is no radio version and/or ID testing: I don't know how and I only have one radio. There is no frequency enforcement for the VFO and Home channels. There is no frequency validation for low<high for the PMS channels The FT-65 is assumed to be (almost) identical to the FT-4. The FT-65 has 4 programmable keys instead of 2 (I coded for these) and some settings I did not code for. I will get to those when I have more access to a FT-65 My UI for the programmable keys is is horrible. The code in not as Pythonic as it should be. I'm basically a C programmer.

2 6

[chirp_devel] python2/3 MemoryMap?
by Dan Clemmensen 18 Feb '19

18 Feb '19

I'm trying to write a driver that works with both Python 2 and Python 3. It works and passes all tests, but it cannot create a memory savable memory map when it downloads from the radio. I can choose MemoryMapBytes, which works in Py3, or MemoryMap, which is implemented in both but which results in a mmap that cannot be written to a file. I'm now officially lost, which is my usual state. Any suggestions?

2 6

[chirp_devel] Tones and DTCS
by Dan Clemmensen 17 Feb '19

17 Feb '19

There are 11 possible combinations recognized by CHIRP: all nine combinations of (none, tone, dtcs) for transmit, and (none, tone, dtcs) for receive, and for the Tone->Tone and DTCS->DTCS cases, the tx and rx are either equal or not equal. The FT-4 radio can support nine of these eleven cases, all except Tone->DTCS and DTCS->Tone. I need my code to do three things: 1) work correctly with the UI for all cases 2) pass the BruteForce unit test 3) pass the CopyAll unit test. I can write code that does any two of these three things, but not all three. This one fails BruteForce: TONE_MODES = ["", "Tone", "TSQL", "DTCS", "DTCS-R", "TSQL-R", "Cross"] CROSS_MODES = ["Tone->Tone", "DTCS->", "DTCS->DTCS", "->DTCS"] BruteForce wants to always get back what it gives you. This one causes the UI to inhibit certain inputs: TONE_MODES = ["", "Tone", "TSQL", "DTCS", "DTCS-R", "TSQL-R", "Cross"] CROSS_MODES = [, "DTCS->DTCS", "->DTCS"] This is interesting because if you get the inputs into the columns by loading a spreadsheet as in the CopyAll test, (e.g., TSQL, 100.0 88.5) CHIRP happily sends it to the driver, but yyou cannot enter it.

1 0

[chirp_devel] Fix for IC2730
by Dan Smith 16 Feb '19

16 Feb '19

Hi Rhett, Apologies if you've already seen it, but I just wanted to call your attention to this issue if not: https://chirp.danplanet.com/issues/6457 In summary, I fixed one of our tests that wasn't actually running, which uncovered an issue with the 2730 driver. As a result, that driver is now failing tests on the master branch and I'd really like to get it fixed up as soon as possible and I'm hoping you can help. Thanks! --Dan

2 2

[chirp_devel] Speed up init for slow computers?
by Dan Clemmensen 16 Feb '19

16 Feb '19

My eventual target is a Raspberry Pi Zero W. It is slow. I only need to support a very few radio types, so I tried removing all of the driver files for the other radios. This fails because ui/mainapp.py imports some of the files, some of which import others. The rest of CHIRP is indifferent, but not mainapp.py. My workaround is to copy in the required files, which is silly. 17 files are needed. of these two files (generic_csv.py and repeaterbook.py) are arguably not actually drivers. and could perhaps be moved up to the chirp.hg/chirp directory. (17 is still a lot better than 125 or so.) Proposal: recode mainapp.py to operate without these files when they are not present. If this is acceptable, I can give it a try. I think this is in the spirit of the CHIRP architecture.

1 0

[chirp_devel] Build test results: Successful
by Build System 15 Feb '19

15 Feb '19

Tested changes: Changes for Build #778 [Dan Smith <dsmith(a)danplanet.com>] Remove old win32 build scripts that are not used anymore and likey no longer work #0 [Tom Hayward <tom(a)tomh.us>] [id880] Fix typo in charset definition. #281 [Tom Hayward <tom(a)tomh.us>] [thf6a] Support full charset (ASCII). Fixes #141 [Tom Hayward <tom(a)tomh.us>] [id880] Support full charset. Fixes #281 [Tom Hayward <tom(a)tomh.us>] [vx5] Support full charset (ASCII). Fixes #292 [Tom Hayward <tom(a)tomh.us>] [id31a] set used bit when creating new memory, clear when deleting. Fixes #269 [Tom Hayward <tom(a)tomh.us>] Support PyGTK < 2.22 in bank edit. Fixes #231 [Tom Hayward <tom(a)tomh.us>] [d710] [v71] [d72] Fix tone list (not all tones are supported). Fixes #212 [Dan Smith <dsmith(a)danplanet.com>] [vx7] Fix setting memory power levels on 220MHz band Fixes #214 [Dan Smith <dsmith(a)danplanet.com>] fips: Pennsylvania FIPS code was wrong. #117 [Marco Filippi <iz3gme.marco(a)gmail.com>] Consider lower bound frequency of each valid_band as valid Fix bug #181 [Tom Hayward <tom(a)tomh.us>] tmd700: allow 8-char names. Fixes #176 [Dan Smith <dsmith(a)danplanet.com>] Fix the "blind deletion" problem, as well as properly direct copy/paste Fixes #172 [David Griffith <dave(a)661.org>] Bug #155 fix: VX-7 1.25m power levels [David Griffith <dave(a)661.org>] New INSTALL and README files Fixes #122 [Tom Hayward <tom(a)tomh.us>] thd72: only use hardware flow on OS X. Fixes #166 [Marco Filippi <iz3gme.marco(a)gmail.com>] [FT817] Tone freq not set correctly Same as #88 for FT857, to avoid code duplication fix code have been moved from ft857 to its ancestor class Fix bug #163 [Tom Hayward <tom(a)tomh.us>] Fix Mac .app so paths with spaces work. Fixes Bug #145 Changes for Build #779 [Dan Smith <dsmith(a)danplanet.com>] Add a test for deleting memories and a radio feature flag for radios that can't Shockingly we were missing an automated test for memory delete. Adding that uncovered several issues in various drivers. Some drivers explicitly do not do delete operations, so mark those in radiofeatures so we can skip the test for them. Related to #6455 #6453 #6451 #6449 [Dan Smith <dsmith(a)danplanet.com>] Fix TH-UV3R-25 memory delete The driver was calling set_raw() with the wrong size data Fixes #6455 [Dan Smith <dsmith(a)danplanet.com>] Fix FT50 calling missing method during memory delete Fixes #6453 [Dan Smith <dsmith(a)danplanet.com>] Make Boblov X3plus properly detect its own deleted memories Fixes #6451 [Dan Smith <dsmith(a)danplanet.com>] Fix set_memory() to always clear extra flags, even if not specified This would cause a set_memory() with no mem.extra to leave values unset, which means a subsequent get_memory() would try to index the feature arrays with a large number. Fixes #6449 [Dan Smith <dsmith(a)danplanet.com>] Change the browser widget to use an HPaned instead of HBox This means the tree panel can be resized, and is necessary for GTK3 to look and behave sanely. Related to work for #495 [Tom Hayward <tom(a)tomh.us>] [id880] Fix typo in charset definition. #281 [Tom Hayward <tom(a)tomh.us>] [thf6a] Support full charset (ASCII). Fixes #141 [Tom Hayward <tom(a)tomh.us>] [id880] Support full charset. Fixes #281 [Tom Hayward <tom(a)tomh.us>] [vx5] Support full charset (ASCII). Fixes #292 [Tom Hayward <tom(a)tomh.us>] [id31a] set used bit when creating new memory, clear when deleting. Fixes #269 [Tom Hayward <tom(a)tomh.us>] Support PyGTK < 2.22 in bank edit. Fixes #231 [Tom Hayward <tom(a)tomh.us>] [d710] [v71] [d72] Fix tone list (not all tones are supported). Fixes #212 [Dan Smith <dsmith(a)danplanet.com>] [vx7] Fix setting memory power levels on 220MHz band Fixes #214 [Dan Smith <dsmith(a)danplanet.com>] fips: Pennsylvania FIPS code was wrong. #117 [Marco Filippi <iz3gme.marco(a)gmail.com>] Consider lower bound frequency of each valid_band as valid Fix bug #181 [Tom Hayward <tom(a)tomh.us>] tmd700: allow 8-char names. Fixes #176 [Dan Smith <dsmith(a)danplanet.com>] Fix the "blind deletion" problem, as well as properly direct copy/paste Fixes #172 [David Griffith <dave(a)661.org>] Bug #155 fix: VX-7 1.25m power levels [David Griffith <dave(a)661.org>] New INSTALL and README files Fixes #122 [Tom Hayward <tom(a)tomh.us>] thd72: only use hardware flow on OS X. Fixes #166 [Marco Filippi <iz3gme.marco(a)gmail.com>] [FT817] Tone freq not set correctly Same as #88 for FT857, to avoid code duplication fix code have been moved from ft857 to its ancestor class Fix bug #163 [Tom Hayward <tom(a)tomh.us>] Fix Mac .app so paths with spaces work. Fixes Bug #145 Full log: [...truncated 274 lines...] Testing Icom ID-51 Plus banks ... ok test_brute_force (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus brute force ... ok test_clone (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus clone ... ok test_copy_all (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus copy all ... ok test_detect (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus detect ... ok test_edges (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus edges ... ok test_settings (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus settings ... ok test_banks (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 brute force ... ok test_clone (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 clone ... ok test_copy_all (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 copy all ... ok test_detect (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 detect ... ok test_edges (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 edges ... skipped 'No mutable memory locations found' test_settings (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 settings ... ok test_banks (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M brute force ... ok test_clone (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M clone ... ok test_copy_all (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M copy all ... ok test_detect (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M detect ... ok test_edges (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M edges ... ok test_settings (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 brute force ... ok test_clone (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 clone ... ok test_copy_all (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 copy all ... ok test_detect (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 detect ... ok test_edges (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 edges ... ok test_settings (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 settings ... ok test_banks (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 brute force ... ok test_clone (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 clone ... ok test_copy_all (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 copy all ... ok test_detect (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 detect ... ok test_edges (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 edges ... ok test_settings (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 settings ... ok test_banks (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 brute force ... ok test_clone (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 clone ... ok test_copy_all (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 copy all ... ok test_detect (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 detect ... ok test_edges (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 edges ... ok test_settings (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomID880H) Testing Icom ID-880H banks ... ok test_brute_force (tests.TestCase_IcomID880H) Testing Icom ID-880H brute force ... ok test_clone (tests.TestCase_IcomID880H) Testing Icom ID-880H clone ... ok test_copy_all (tests.TestCase_IcomID880H) Testing Icom ID-880H copy all ... ok test_detect (tests.TestCase_IcomID880H) Testing Icom ID-880H detect ... ok test_edges (tests.TestCase_IcomID880H) Testing Icom ID-880H edges ... ok test_settings (tests.TestCase_IcomID880H) Testing Icom ID-880H settings ... ok test_banks (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D banks ... ok test_brute_force (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D brute force ... ok test_clone (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D clone ... ok test_copy_all (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D copy all ... ok test_detect (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D detect ... ok test_edges (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D edges ... ok test_settings (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D settings ... ok test_banks (tests.TestCase_RetevisRT26) Testing Retevis RT26 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT26) Testing Retevis RT26 brute force ... ok test_clone (tests.TestCase_RetevisRT26) Testing Retevis RT26 clone ... ok test_copy_all (tests.TestCase_RetevisRT26) Testing Retevis RT26 copy all ... ok test_detect (tests.TestCase_RetevisRT26) Testing Retevis RT26 detect ... ok test_edges (tests.TestCase_RetevisRT26) Testing Retevis RT26 edges ... ok test_settings (tests.TestCase_RetevisRT26) Testing Retevis RT26 settings ... ok test_banks (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R brute force ... ok test_clone (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R clone ... ok test_copy_all (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R copy all ... ok test_detect (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R detect ... ok test_edges (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R edges ... ok test_settings (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R settings ... ok test_banks (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 brute force ... ok test_clone (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 clone ... ok test_copy_all (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 copy all ... ok test_detect (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 detect ... ok test_edges (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 edges ... ok test_settings (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 settings ... ok test_banks (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R brute force ... ok test_clone (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R clone ... ok test_copy_all (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R copy all ... ok test_detect (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R detect ... ok test_edges (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R edges ... ok test_settings (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND brute force ... ok test_clone (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND clone ... ok test_copy_all (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND copy all ... ok test_detect (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND detect ... ok test_edges (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND edges ... ok test_settings (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND settings ... ok test_banks (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H banks ... ok test_brute_force (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H brute force ... ok test_clone (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H clone ... ok test_copy_all (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H copy all ... ok test_detect (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H detect ... ok test_edges (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H edges ... ok test_settings (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H settings ... ok test_banks (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M brute force ... ok test_clone (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M clone ... ok test_copy_all (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M copy all ... ok test_detect (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M detect ... ok test_edges (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M edges ... ok test_settings (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 brute force ... ok test_clone (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 clone ... ok test_copy_all (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 copy all ... ok test_detect (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 detect ... ok test_edges (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 edges ... ok test_settings (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH brute force ... ok test_clone (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH clone ... ok test_copy_all (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH copy all ... ok test_detect (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH detect ... ok test_edges (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH edges ... ok test_settings (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH settings ... ok test_banks (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 brute force ... ok test_clone (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 clone ... ok test_copy_all (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 copy all ... ok test_detect (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 detect ... ok test_edges (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 edges ... ok test_settings (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 settings ... ok test_banks (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 brute force ... ok test_clone (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 clone ... ok test_copy_all (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 copy all ... ok test_detect (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 detect ... ok test_edges (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 edges ... ok test_settings (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 settings ... ok test_banks (tests.TestCase_IcomICT7H) Testing Icom IC-T7H banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICT7H) Testing Icom IC-T7H brute force ... ok test_clone (tests.TestCase_IcomICT7H) Testing Icom IC-T7H clone ... ok test_copy_all (tests.TestCase_IcomICT7H) Testing Icom IC-T7H copy all ... ok test_detect (tests.TestCase_IcomICT7H) Testing Icom IC-T7H detect ... ok test_edges (tests.TestCase_IcomICT7H) Testing Icom IC-T7H edges ... ok test_settings (tests.TestCase_IcomICT7H) Testing Icom IC-T7H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 brute force ... ok test_clone (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 clone ... ok test_copy_all (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 copy all ... ok test_detect (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 detect ... ok test_edges (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 edges ... ok test_settings (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H banks ... ok test_brute_force (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H brute force ... ok test_clone (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H clone ... ok test_copy_all (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H copy all ... ok test_detect (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H detect ... ok test_edges (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H edges ... ok test_settings (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H settings ... ok test_banks (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 banks ... ok test_brute_force (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 brute force ... ok test_clone (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 clone ... ok test_copy_all (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 copy all ... ok test_detect (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 detect ... ok test_edges (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 edges ... ok test_settings (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A brute force ... ok test_clone (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A clone ... ok test_copy_all (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A copy all ... ok test_detect (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A detect ... ok test_edges (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A edges ... ok test_settings (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A settings ... ok test_banks (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 brute force ... ok test_clone (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 clone ... ok test_copy_all (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 copy all ... ok test_detect (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 detect ... ok test_edges (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 edges ... ok test_settings (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 settings ... ok test_banks (tests.TestCase_TYTTH350) Testing TYT TH-350 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTH350) Testing TYT TH-350 brute force ... ok test_clone (tests.TestCase_TYTTH350) Testing TYT TH-350 clone ... ok test_copy_all (tests.TestCase_TYTTH350) Testing TYT TH-350 copy all ... ok test_detect (tests.TestCase_TYTTH350) Testing TYT TH-350 detect ... ok test_edges (tests.TestCase_TYTTH350) Testing TYT TH-350 edges ... ok test_settings (tests.TestCase_TYTTH350) Testing TYT TH-350 settings ... ok test_banks (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 brute force ... ok test_clone (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 clone ... ok test_copy_all (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 copy all ... ok test_detect (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 detect ... ok test_edges (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 edges ... ok test_settings (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 settings ... ok test_banks (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R brute force ... ok test_clone (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R clone ... ok test_copy_all (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R copy all ... ok test_detect (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R detect ... ok test_edges (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R edges ... ok test_settings (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R settings ... ok test_banks (tests.TestCase_RadioddityR2) Testing Radioddity R2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RadioddityR2) Testing Radioddity R2 brute force ... ok test_clone (tests.TestCase_RadioddityR2) Testing Radioddity R2 clone ... ok test_copy_all (tests.TestCase_RadioddityR2) Testing Radioddity R2 copy all ... ok test_detect (tests.TestCase_RadioddityR2) Testing Radioddity R2 detect ... ok test_edges (tests.TestCase_RadioddityR2) Testing Radioddity R2 edges ... ok test_settings (tests.TestCase_RadioddityR2) Testing Radioddity R2 settings ... ok test_banks (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R brute force ... ok test_clone (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R clone ... ok test_copy_all (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R copy all ... ok test_detect (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R detect ... ok test_edges (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R edges ... ok test_settings (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R settings ... ok test_banks (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 brute force ... ok test_clone (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 clone ... ok test_copy_all (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 copy all ... ok test_detect (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 detect ... ok test_edges (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 edges ... ok test_settings (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 settings ... ok test_banks (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M brute force ... ok test_clone (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M clone ... ok test_copy_all (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M copy all ... ok test_detect (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M detect ... ok test_edges (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M edges ... ok test_settings (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M settings ... ok test_banks (tests.TestCase_IcomICP7) Testing Icom IC-P7 banks ... ok test_brute_force (tests.TestCase_IcomICP7) Testing Icom IC-P7 brute force ... ok test_clone (tests.TestCase_IcomICP7) Testing Icom IC-P7 clone ... ok test_copy_all (tests.TestCase_IcomICP7) Testing Icom IC-P7 copy all ... ok test_detect (tests.TestCase_IcomICP7) Testing Icom IC-P7 detect ... ok test_edges (tests.TestCase_IcomICP7) Testing Icom IC-P7 edges ... ok test_settings (tests.TestCase_IcomICP7) Testing Icom IC-P7 settings ... ok test_banks (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus brute force ... ok test_clone (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus clone ... ok test_copy_all (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus copy all ... ok test_detect (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus detect ... ok test_edges (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus edges ... ok test_settings (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus settings ... ok test_banks (tests.TestCase_IcomICW32E) Testing Icom IC-W32E banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICW32E) Testing Icom IC-W32E brute force ... ok test_clone (tests.TestCase_IcomICW32E) Testing Icom IC-W32E clone ... ok test_copy_all (tests.TestCase_IcomICW32E) Testing Icom IC-W32E copy all ... ok test_detect (tests.TestCase_IcomICW32E) Testing Icom IC-W32E detect ... ok test_edges (tests.TestCase_IcomICW32E) Testing Icom IC-W32E edges ... ok test_settings (tests.TestCase_IcomICW32E) Testing Icom IC-W32E settings ... skipped 'Settings not supported' test_banks (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M brute force ... ok test_clone (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M clone ... ok test_copy_all (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M copy all ... ok test_detect (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M detect ... ok test_edges (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M edges ... ok test_settings (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M settings ... ok test_banks (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 brute force ... ok test_clone (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 clone ... ok test_copy_all (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 copy all ... ok test_detect (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 detect ... ok test_edges (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 edges ... ok test_settings (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 brute force ... ok test_clone (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 clone ... ok test_copy_all (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 copy all ... ok test_detect (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 detect ... ok test_edges (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 edges ... ok test_settings (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 settings ... ok test_banks (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 brute force ... ok test_clone (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 clone ... ok test_copy_all (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 copy all ... ok test_detect (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 detect ... ok test_edges (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 edges ... ok test_settings (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 settings ... ok test_banks (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D banks ... ok test_brute_force (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D brute force ... ok test_clone (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D clone ... ok test_copy_all (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D copy all ... ok test_detect (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D detect ... ok test_edges (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D edges ... ok test_settings (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D settings ... ok test_banks (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) brute force ... ok test_clone (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) clone ... ok test_copy_all (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) copy all ... ok test_detect (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) detect ... ok test_edges (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) edges ... ok test_settings (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) settings ... ok test_banks (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D brute force ... ok test_clone (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D clone ... ok test_copy_all (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D copy all ... ok test_detect (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D detect ... ok test_edges (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D edges ... ok test_settings (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 banks ... ok test_brute_force (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 brute force ... ok test_clone (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 clone ... ok test_copy_all (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 copy all ... ok test_detect (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 detect ... ok test_edges (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 edges ... ok test_settings (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 settings ... ok test_banks (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H brute force ... ok test_clone (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H clone ... ok test_copy_all (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H copy all ... ok test_detect (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H detect ... ok test_edges (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H edges ... ok test_settings (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 brute force ... ok test_clone (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 clone ... ok test_copy_all (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 copy all ... ok test_detect (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 detect ... ok test_edges (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 edges ... ok test_settings (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_LeixenVV898) Testing Leixen VV-898 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_LeixenVV898) Testing Leixen VV-898 brute force ... ok test_clone (tests.TestCase_LeixenVV898) Testing Leixen VV-898 clone ... ok test_copy_all (tests.TestCase_LeixenVV898) Testing Leixen VV-898 copy all ... ok test_detect (tests.TestCase_LeixenVV898) Testing Leixen VV-898 detect ... ok test_edges (tests.TestCase_LeixenVV898) Testing Leixen VV-898 edges ... ok test_settings (tests.TestCase_LeixenVV898) Testing Leixen VV-898 settings ... ok test_banks (tests.TestCase_QYTKT7900D) Testing QYT KT7900D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_QYTKT7900D) Testing QYT KT7900D brute force ... ok test_clone (tests.TestCase_QYTKT7900D) Testing QYT KT7900D clone ... ok test_copy_all (tests.TestCase_QYTKT7900D) Testing QYT KT7900D copy all ... ok test_detect (tests.TestCase_QYTKT7900D) Testing QYT KT7900D detect ... ok test_edges (tests.TestCase_QYTKT7900D) Testing QYT KT7900D edges ... ok test_settings (tests.TestCase_QYTKT7900D) Testing QYT KT7900D settings ... ok test_banks (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P brute force ... ok test_clone (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P clone ... ok test_copy_all (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P copy all ... ok test_detect (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P detect ... ok test_edges (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P edges ... ok test_settings (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P settings ... ok test_banks (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 banks ... ok test_brute_force (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 brute force ... ok test_clone (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 clone ... ok test_copy_all (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 copy all ... ok test_detect (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 detect ... ok test_edges (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 edges ... ok test_settings (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomICW32A) Testing Icom IC-W32A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICW32A) Testing Icom IC-W32A brute force ... ok test_clone (tests.TestCase_IcomICW32A) Testing Icom IC-W32A clone ... ok test_copy_all (tests.TestCase_IcomICW32A) Testing Icom IC-W32A copy all ... ok test_detect (tests.TestCase_IcomICW32A) Testing Icom IC-W32A detect ... ok test_edges (tests.TestCase_IcomICW32A) Testing Icom IC-W32A edges ... ok test_settings (tests.TestCase_IcomICW32A) Testing Icom IC-W32A settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 banks ... ok test_brute_force (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 brute force ... ok test_clone (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 clone ... ok test_copy_all (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 copy all ... ok test_detect (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 detect ... ok test_edges (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 edges ... ok test_settings (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 settings ... ok test_banks (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B brute force ... ok test_clone (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B clone ... ok test_copy_all (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B copy all ... ok test_detect (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B detect ... ok test_edges (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B edges ... ok test_settings (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B settings ... ok test_banks (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R brute force ... ok test_clone (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R clone ... ok test_copy_all (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R copy all ... ok test_detect (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R detect ... ok test_edges (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R edges ... ok test_settings (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R settings ... ok test_banks (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 brute force ... ok test_clone (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 clone ... ok test_copy_all (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 copy all ... ok test_detect (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 detect ... ok test_edges (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 edges ... ok test_settings (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 settings ... ok test_banks (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 brute force ... ok test_clone (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 clone ... ok test_copy_all (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 copy all ... ok test_detect (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 detect ... ok test_edges (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 edges ... ok test_settings (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 settings ... ok test_banks (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV brute force ... ok test_clone (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV clone ... ok test_copy_all (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV copy all ... ok test_detect (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV detect ... ok test_edges (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV edges ... ok test_settings (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV settings ... ok test_banks (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 brute force ... ok test_clone (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 clone ... ok test_copy_all (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 copy all ... ok test_detect (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 detect ... ok test_edges (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 edges ... ok test_settings (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 settings ... ok test_banks (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M brute force ... ok test_clone (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M clone ... ok test_copy_all (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M copy all ... ok test_detect (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M detect ... ok test_edges (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M edges ... ok test_settings (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M settings ... ok test_banks (tests.TestCase_KYDNC630A) Testing KYD NC-630A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KYDNC630A) Testing KYD NC-630A brute force ... ok test_clone (tests.TestCase_KYDNC630A) Testing KYD NC-630A clone ... ok test_copy_all (tests.TestCase_KYDNC630A) Testing KYD NC-630A copy all ... ok test_detect (tests.TestCase_KYDNC630A) Testing KYD NC-630A detect ... ok test_edges (tests.TestCase_KYDNC630A) Testing KYD NC-630A edges ... ok test_settings (tests.TestCase_KYDNC630A) Testing KYD NC-630A settings ... ok test_banks (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 brute force ... ok test_clone (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 clone ... ok test_copy_all (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 copy all ... ok test_detect (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 detect ... ok test_edges (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 edges ... ok test_settings (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 settings ... ok test_banks (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 brute force ... ok test_clone (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 clone ... ok test_copy_all (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 copy all ... ok test_detect (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 detect ... ok test_edges (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 edges ... ok test_settings (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 settings ... ok test_banks (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 brute force ... ok test_clone (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 clone ... ok test_copy_all (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 copy all ... ok test_detect (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 detect ... ok test_edges (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 edges ... ok test_settings (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M brute force ... ok test_clone (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M clone ... ok test_copy_all (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M copy all ... ok test_detect (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M detect ... ok test_edges (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M edges ... ok test_settings (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H banks ... ok test_brute_force (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H brute force ... ok test_clone (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H clone ... ok test_copy_all (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H copy all ... ok test_detect (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H detect ... ok test_edges (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H edges ... ok test_settings (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 brute force ... ok test_clone (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 clone ... ok test_copy_all (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 copy all ... ok test_detect (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 detect ... ok test_edges (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 edges ... ok test_settings (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 settings ... ok test_banks (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 brute force ... ok test_clone (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 clone ... ok test_copy_all (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 copy all ... ok test_detect (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 detect ... ok test_edges (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 edges ... ok test_settings (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 settings ... ok test_banks (tests.TestCase_IcomID51) Testing Icom ID-51 banks ... ok test_brute_force (tests.TestCase_IcomID51) Testing Icom ID-51 brute force ... ok test_clone (tests.TestCase_IcomID51) Testing Icom ID-51 clone ... ok test_copy_all (tests.TestCase_IcomID51) Testing Icom ID-51 copy all ... ok test_detect (tests.TestCase_IcomID51) Testing Icom ID-51 detect ... ok test_edges (tests.TestCase_IcomID51) Testing Icom ID-51 edges ... ok test_settings (tests.TestCase_IcomID51) Testing Icom ID-51 settings ... ok test_banks (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) brute force ... ok test_clone (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) clone ... ok test_copy_all (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) copy all ... ok test_detect (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) detect ... ok test_edges (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) edges ... ok test_settings (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) settings ... ok test_banks (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR banks ... ok test_brute_force (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR brute force ... ok test_clone (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR clone ... ok test_copy_all (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR copy all ... ok test_detect (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR detect ... ok test_edges (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR edges ... ok test_settings (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR settings ... ok test_banks (tests.TestCase_RadtelT18) Testing Radtel T18 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RadtelT18) Testing Radtel T18 brute force ... ok test_clone (tests.TestCase_RadtelT18) Testing Radtel T18 clone ... ok test_copy_all (tests.TestCase_RadtelT18) Testing Radtel T18 copy all ... ok test_detect (tests.TestCase_RadtelT18) Testing Radtel T18 detect ... ok test_edges (tests.TestCase_RadtelT18) Testing Radtel T18 edges ... ok test_settings (tests.TestCase_RadtelT18) Testing Radtel T18 settings ... ok test_banks (tests.TestCase_BaofengF11) Testing Baofeng F-11 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengF11) Testing Baofeng F-11 brute force ... ok test_clone (tests.TestCase_BaofengF11) Testing Baofeng F-11 clone ... ok test_copy_all (tests.TestCase_BaofengF11) Testing Baofeng F-11 copy all ... ok test_detect (tests.TestCase_BaofengF11) Testing Baofeng F-11 detect ... ok test_edges (tests.TestCase_BaofengF11) Testing Baofeng F-11 edges ... ok test_settings (tests.TestCase_BaofengF11) Testing Baofeng F-11 settings ... ok test_banks (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A brute force ... ok test_clone (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A clone ... ok test_copy_all (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A copy all ... ok test_detect (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A detect ... ok test_edges (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A edges ... ok test_settings (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A settings ... ok test_banks (tests.TestCase_AlincoDJ175) Testing Alinco DJ175 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AlincoDJ175) Testing Alinco DJ175 brute force ... ok test_clone (tests.TestCase_AlincoDJ175) Testing Alinco DJ175 clone ... ok test_copy_all (tests.TestCase_AlincoDJ175) Testing Alinco DJ175 copy all ... ok test_detect (tests.TestCase_AlincoDJ175) Testing Alinco DJ175 detect ... ok test_edges (tests.TestCase_AlincoDJ175) Testing Alinco DJ175 edges ... ok test_settings (tests.TestCase_AlincoDJ175) Testing Alinco DJ175 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 brute force ... ok test_clone (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 clone ... ok test_copy_all (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 copy all ... ok test_detect (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 detect ... ok test_edges (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 edges ... ok test_settings (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 settings ... ok test_banks (tests.TestCase_RetevisRT22) Testing Retevis RT22 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT22) Testing Retevis RT22 brute force ... ok test_clone (tests.TestCase_RetevisRT22) Testing Retevis RT22 clone ... ok test_copy_all (tests.TestCase_RetevisRT22) Testing Retevis RT22 copy all ... ok test_detect (tests.TestCase_RetevisRT22) Testing Retevis RT22 detect ... ok test_edges (tests.TestCase_RetevisRT22) Testing Retevis RT22 edges ... ok test_settings (tests.TestCase_RetevisRT22) Testing Retevis RT22 settings ... ok test_banks (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R banks ... ok test_brute_force (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R brute force ... ok test_clone (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R clone ... ok test_copy_all (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R copy all ... ok test_detect (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R detect ... ok test_edges (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R edges ... ok test_settings (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R settings ... ok test_banks (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG brute force ... ok test_clone (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG clone ... ok test_copy_all (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG copy all ... ok test_detect (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG detect ... ok test_edges (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG edges ... ok test_settings (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG settings ... skipped 'Settings not supported' test_banks (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S brute force ... ok test_clone (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S clone ... ok test_copy_all (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S copy all ... ok test_detect (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S detect ... ok test_edges (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S edges ... ok test_settings (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S settings ... ok test_banks (tests.TestCase_KYDIP620) Testing KYD IP-620 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KYDIP620) Testing KYD IP-620 brute force ... ok test_clone (tests.TestCase_KYDIP620) Testing KYD IP-620 clone ... ok test_copy_all (tests.TestCase_KYDIP620) Testing KYD IP-620 copy all ... ok test_detect (tests.TestCase_KYDIP620) Testing KYD IP-620 detect ... ok test_edges (tests.TestCase_KYDIP620) Testing KYD IP-620 edges ... ok test_settings (tests.TestCase_KYDIP620) Testing KYD IP-620 settings ... ok test_banks (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 banks ... ok test_brute_force (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 brute force ... ok test_clone (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 clone ... ok test_copy_all (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 copy all ... ok test_detect (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 detect ... ok test_edges (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 edges ... ok test_settings (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 settings ... ok test_banks (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 banks ... ok test_brute_force (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 brute force ... ok test_clone (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 clone ... ok test_copy_all (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 copy all ... ok test_detect (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 detect ... ok test_edges (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 edges ... ok test_settings (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 settings ... ok test_banks (tests.TestCase_WouxunKGUV8DPlus) Testing Wouxun KG-UV8D Plus banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUV8DPlus) Testing Wouxun KG-UV8D Plus brute force ... ok test_clone (tests.TestCase_WouxunKGUV8DPlus) Testing Wouxun KG-UV8D Plus clone ... ok test_copy_all (tests.TestCase_WouxunKGUV8DPlus) Testing Wouxun KG-UV8D Plus copy all ... ok test_detect (tests.TestCase_WouxunKGUV8DPlus) Testing Wouxun KG-UV8D Plus detect ... ok test_edges (tests.TestCase_WouxunKGUV8DPlus) Testing Wouxun KG-UV8D Plus edges ... ok test_settings (tests.TestCase_WouxunKGUV8DPlus) Testing Wouxun KG-UV8D Plus settings ... ok test_banks (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D brute force ... ok test_clone (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D clone ... ok test_copy_all (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D copy all ... ok test_detect (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D detect ... ok test_edges (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D edges ... ok test_settings (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D settings ... ok test_banks (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G banks ... ok test_brute_force (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G brute force ... ok test_clone (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G clone ... ok test_copy_all (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G copy all ... ok test_detect (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G detect ... ok test_edges (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G edges ... ok test_settings (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G settings ... ok test_banks (tests.TestCase_QYTKT8900D) Testing QYT KT8900D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_QYTKT8900D) Testing QYT KT8900D brute force ... ok test_clone (tests.TestCase_QYTKT8900D) Testing QYT KT8900D clone ... ok test_copy_all (tests.TestCase_QYTKT8900D) Testing QYT KT8900D copy all ... ok test_detect (tests.TestCase_QYTKT8900D) Testing QYT KT8900D detect ... ok test_edges (tests.TestCase_QYTKT8900D) Testing QYT KT8900D edges ... ok test_settings (tests.TestCase_QYTKT8900D) Testing QYT KT8900D settings ... ok test_banks (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G banks ... ok test_brute_force (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G brute force ... ok test_clone (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G clone ... ok test_copy_all (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G copy all ... ok test_detect (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G detect ... ok test_edges (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G edges ... ok test_settings (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G settings ... ok test_banks (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 banks ... ok test_brute_force (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 brute force ... ok test_clone (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 clone ... ok test_copy_all (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 copy all ... ok test_detect (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 detect ... ok test_edges (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 edges ... ok test_settings (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomIC208H) Testing Icom IC-208H banks ... ok test_brute_force (tests.TestCase_IcomIC208H) Testing Icom IC-208H brute force ... ok test_clone (tests.TestCase_IcomIC208H) Testing Icom IC-208H clone ... ok test_copy_all (tests.TestCase_IcomIC208H) Testing Icom IC-208H copy all ... ok test_detect (tests.TestCase_IcomIC208H) Testing Icom IC-208H detect ... ok test_edges (tests.TestCase_IcomIC208H) Testing Icom IC-208H edges ... ok test_settings (tests.TestCase_IcomIC208H) Testing Icom IC-208H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomID31A) Testing Icom ID-31A banks ... ok test_brute_force (tests.TestCase_IcomID31A) Testing Icom ID-31A brute force ... ok test_clone (tests.TestCase_IcomID31A) Testing Icom ID-31A clone ... ok test_copy_all (tests.TestCase_IcomID31A) Testing Icom ID-31A copy all ... ok test_detect (tests.TestCase_IcomID31A) Testing Icom ID-31A detect ... ok test_edges (tests.TestCase_IcomID31A) Testing Icom ID-31A edges ... ok test_settings (tests.TestCase_IcomID31A) Testing Icom ID-31A settings ... ok test_banks (tests.TestCase_TYTTH7800) Testing TYT TH-7800 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTH7800) Testing TYT TH-7800 brute force ... ok test_clone (tests.TestCase_TYTTH7800) Testing TYT TH-7800 clone ... ok test_copy_all (tests.TestCase_TYTTH7800) Testing TYT TH-7800 copy all ... ok test_detect (tests.TestCase_TYTTH7800) Testing TYT TH-7800 detect ... ok test_edges (tests.TestCase_TYTTH7800) Testing TYT TH-7800 edges ... ok test_settings (tests.TestCase_TYTTH7800) Testing TYT TH-7800 settings ... ok test_banks (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H banks ... ok test_brute_force (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H brute force ... ok test_clone (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H clone ... ok test_copy_all (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H copy all ... ok test_detect (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H detect ... ok test_edges (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H edges ... ok test_settings (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H settings ... ok test_banks (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K brute force ... ok test_clone (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K clone ... ok test_copy_all (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K copy all ... ok test_detect (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K detect ... ok test_edges (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K edges ... ok test_settings (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K settings ... ok test_banks (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 brute force ... ok test_clone (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 clone ... ok test_copy_all (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 copy all ... ok test_detect (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 detect ... ok test_edges (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 edges ... ok test_settings (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 settings ... ok test_banks (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A banks ... ok test_brute_force (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A brute force ... ok test_clone (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A clone ... ok test_copy_all (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A copy all ... ok test_detect (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A detect ... ok test_edges (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A edges ... ok test_settings (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A settings ... ok test_banks (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R brute force ... ok test_clone (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R clone ... ok test_copy_all (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R copy all ... ok test_detect (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R detect ... ok test_edges (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R edges ... ok test_settings (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R settings ... ok test_banks (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 brute force ... ok test_clone (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 clone ... ok test_copy_all (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 copy all ... ok test_detect (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 detect ... ok test_edges (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 edges ... ok test_settings (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 settings ... ok test_banks (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 banks ... ok test_brute_force (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 brute force ... ok test_clone (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 clone ... ok test_copy_all (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 copy all ... ok test_detect (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 detect ... ok test_edges (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 edges ... ok test_settings (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A brute force ... ok test_clone (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A clone ... ok test_copy_all (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A copy all ... ok test_detect (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A detect ... ok test_edges (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A edges ... ok test_settings (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A settings ... ok test_banks (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE banks ... ok test_brute_force (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE brute force ... ok test_clone (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE clone ... ok test_copy_all (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE copy all ... ok test_detect (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE detect ... ok test_edges (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE edges ... ok test_settings (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE settings ... ok test_banks (tests.TestCase_IcomICT70) Testing Icom IC-T70 banks ... ok test_brute_force (tests.TestCase_IcomICT70) Testing Icom IC-T70 brute force ... ok test_clone (tests.TestCase_IcomICT70) Testing Icom IC-T70 clone ... ok test_copy_all (tests.TestCase_IcomICT70) Testing Icom IC-T70 copy all ... ok test_detect (tests.TestCase_IcomICT70) Testing Icom IC-T70 detect ... ok test_edges (tests.TestCase_IcomICT70) Testing Icom IC-T70 edges ... ok test_settings (tests.TestCase_IcomICT70) Testing Icom IC-T70 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R brute force ... ok test_clone (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R clone ... ok test_copy_all (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R copy all ... ok test_detect (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R detect ... ok test_edges (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R edges ... ok test_settings (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D banks ... ok test_brute_force (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D brute force ... ok test_clone (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D clone ... ok test_copy_all (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D copy all ... ok test_detect (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D detect ... ok test_edges (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D edges ... ok test_settings (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D settings ... ok test_banks (tests.TestCase_RetevisRT23) Testing Retevis RT23 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT23) Testing Retevis RT23 brute force ... ok test_clone (tests.TestCase_RetevisRT23) Testing Retevis RT23 clone ... ok test_copy_all (tests.TestCase_RetevisRT23) Testing Retevis RT23 copy all ... ok test_detect (tests.TestCase_RetevisRT23) Testing Retevis RT23 detect ... ok test_edges (tests.TestCase_RetevisRT23) Testing Retevis RT23 edges ... ok test_settings (tests.TestCase_RetevisRT23) Testing Retevis RT23 settings ... ok test_banks (tests.TestCase_PuxingPX777) Testing Puxing PX-777 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_PuxingPX777) Testing Puxing PX-777 brute force ... ok test_clone (tests.TestCase_PuxingPX777) Testing Puxing PX-777 clone ... ok test_copy_all (tests.TestCase_PuxingPX777) Testing Puxing PX-777 copy all ... ok test_detect (tests.TestCase_PuxingPX777) Testing Puxing PX-777 detect ... ok test_edges (tests.TestCase_PuxingPX777) Testing Puxing PX-777 edges ... ok test_settings (tests.TestCase_PuxingPX777) Testing Puxing PX-777 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomID800H) Testing Icom ID-800H banks ... ok test_brute_force (tests.TestCase_IcomID800H) Testing Icom ID-800H brute force ... ok test_clone (tests.TestCase_IcomID800H) Testing Icom ID-800H clone ... ok test_copy_all (tests.TestCase_IcomID800H) Testing Icom ID-800H copy all ... ok test_detect (tests.TestCase_IcomID800H) Testing Icom ID-800H detect ... ok test_edges (tests.TestCase_IcomID800H) Testing Icom ID-800H edges ... ok test_settings (tests.TestCase_IcomID800H) Testing Icom ID-800H settings ... ok test_banks (tests.TestCase_AlincoDR235T) Testing Alinco DR235T banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AlincoDR235T) Testing Alinco DR235T brute force ... ok test_clone (tests.TestCase_AlincoDR235T) Testing Alinco DR235T clone ... ok test_copy_all (tests.TestCase_AlincoDR235T) Testing Alinco DR235T copy all ... ok test_detect (tests.TestCase_AlincoDR235T) Testing Alinco DR235T detect ... ok test_edges (tests.TestCase_AlincoDR235T) Testing Alinco DR235T edges ... ok test_settings (tests.TestCase_AlincoDR235T) Testing Alinco DR235T settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D brute force ... ok test_clone (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D clone ... ok test_copy_all (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D copy all ... ok test_detect (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D detect ... ok test_edges (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D edges ... ok test_settings (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D settings ... ok test_banks (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 banks ... ok test_brute_force (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 brute force ... ok test_clone (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 clone ... ok test_copy_all (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 copy all ... ok test_detect (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 detect ... ok test_edges (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 edges ... ok test_settings (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus brute force ... ok test_clone (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus clone ... ok test_copy_all (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus copy all ... ok test_detect (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus detect ... ok test_edges (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus edges ... ok test_settings (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus settings ... ok test_banks (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B brute force ... ok test_clone (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B clone ... ok test_copy_all (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B copy all ... ok test_detect (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B detect ... ok test_edges (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B edges ... ok test_settings (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B settings ... ok test_banks (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R banks ... ok test_brute_force (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R brute force ... ok test_clone (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R clone ... ok test_copy_all (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R copy all ... ok test_detect (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R detect ... ok test_edges (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R edges ... ok test_settings (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R settings ... ok test_banks (tests.TestCase_RetevisRT21) Testing Retevis RT21 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT21) Testing Retevis RT21 brute force ... ok test_clone (tests.TestCase_RetevisRT21) Testing Retevis RT21 clone ... ok test_copy_all (tests.TestCase_RetevisRT21) Testing Retevis RT21 copy all ... ok test_detect (tests.TestCase_RetevisRT21) Testing Retevis RT21 detect ... ok test_edges (tests.TestCase_RetevisRT21) Testing Retevis RT21 edges ... ok test_settings (tests.TestCase_RetevisRT21) Testing Retevis RT21 settings ... ok test_banks (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) brute force ... ok test_clone (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) clone ... ok test_copy_all (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) copy all ... ok test_detect (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) detect ... ok test_edges (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) edges ... ok test_settings (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) settings ... ok ---------------------------------------------------------------------- Ran 819 tests in 211.947s OK (skipped=116) style create: /chirp/.tox/style style installdeps: pep8==1.6.2 style inst: /chirp/.tox/.tmp/package/1/chirp-0.3.0dev.zip style installed: DEPRECATION: Python 2.7 will reach the end of its life on January 1st, 2020. Please upgrade your Python as Python 2.7 won't be maintained after that date. A future version of pip will drop support for Python 2.7.,chirp==0.3.0.dev0,filelock==3.0.10,Mako==1.0.3,MarkupSafe==0.23,mercurial==3.7.3,pep8==1.6.2,pluggy==0.8.1,py==1.7.0,pygobject==3.20.0,pyserial==3.0.1,six==1.12.0,toml==0.10.0,tox==3.7.0,virtualenv==16.4.0 style run-test-pre: PYTHONHASHSEED='2181090876' style runtests: commands[0] | python ./tools/cpep8.py ___________________________________ summary ____________________________________ unit: commands succeeded driver: commands succeeded style: commands succeeded congratulations :) Email was triggered for: Success Sending email for trigger: Success

1 0

[chirp_devel] uv5r under py3
by Dan Smith 12 Feb '19

12 Feb '19

Hi, I think the uv5r driver is likely one of the most widely-used with chirp. So, I just spent some time converting it to work on python3 (which was pretty easy on the face of it). I've lightly tested it with one UV-5R I have, but it is a highly-nuanced driver, with clone support for many variants and versions. Jim, could you check out the py3 branch and give it a good test with a linux machine? On a debian-based machine, that would require python3, python3-gi, python3-serial and I think python3-cairo to be installed if you don't already have them. Then just run "python3 chirpw" and maybe make sure in the Help->About box that it's running under 3.x. Also making sure that it runs properly in python2 is important (i.e. run the same chirpw with python instead of python3 and make sure it's cool there too). Thanks! --Dan

1 0

Jump to page: