- Developers - lists.chirpmyradio.com

[chirp_devel] New driver for Radtel RT-490 and clones (fix #9665) (patch)
by angelof9 15 May '22

15 May '22

Hello, Please find the patch for a new driver for Radtel RT-490 and its clones (8 at this moment). Driver supports: - Radtel RT-490, - MMLradio 8629, - JJCC 8629, - Socotran JC8629, - Socotran FB8629, - Jianpai 8629, - Boristone 8RS, - Abbree AR869, - HamGeek HG590. Support ALL official software features. Plus these new features: - FM preset - Channel memory preset - Killswitch setup (+ can revive killed radios) - Bands settings for 4 bands ranges + tx on/off - Fixed issue of radio being corrupted with official software with custom (channel/ani) names - Included basic help for custom features - Disable radio identification string verification (good to recover from a bad state) Regards,Ao9. Sent with ProtonMail secure email.

2 2

[chirp_devel] Build test results: Successful
by Build System 15 May '22

15 May '22

Tested changes: [Jim Unroe <rock.unroe(a)gmail.com>] [TD-UV5R TriPower] TIDRADIO TD-UV-5R TriPower Incorrect Alias The TIDRADIO TriPower (tri-power) radio was mistakenly aliased to the Radioddity/Baofeng UV-5RX3 (tri-band) model. It should have instead have been aliased to the Baofeng BF-F8HP (tri-power) model. This patch moves the alias to the correct model. fixes #9870 [Jim Unroe <rock.unroe(a)gmail.com>] [GMRS-V2] New Model: Baofeng TEch GMRS-V2 This patch adds support for the BTech GMRS-V2 #9863 [Jim Unroe <rock.unroe(a)gmail.com>] [MURS-V1] Add Display and Edit Alarm Code Feature This patch adds the ability to display and edit the Alarm Code. fixes #9861 [Jim Unroe <rock.unroe(a)gmail.com>] [GMRS-V1] Add Display and Edit Alarm Code Feature This patch adds the ability to display and edit the Alarm Code. fixes #9860 [Jim Unroe <rock.unroe(a)gmail.com>] [MURS-V1] Fix PTT ID Delay (PTT-LT) Upper Limit Check The driver for the MURS-V1 currently considers PTT-LT values above 30 as out-of-range and forces them to the factory devault value of 5. The actual upper limit is 50. This patch sets the upper limit check to 50 (0x32). fixes #9858 [Jim Unroe <rock.unroe(a)gmail.com>] [GMRS-V1] Fix PTT ID Delay (PTT-LT) Upper Limit Check The driver for the GMRS-V1 currently considers PTT-LT values above 30 as out-of-range and forces them to the factory devault value of 5. The actual upper limit is 50. This patch sets the upper limit check to 50 (0x32). fixes #9858 [Tom Hayward <tom(a)tomh.us>] [id880] Fix typo in charset definition. #281 [Tom Hayward <tom(a)tomh.us>] [thf6a] Support full charset (ASCII). Fixes #141 [Tom Hayward <tom(a)tomh.us>] [id880] Support full charset. Fixes #281 [Tom Hayward <tom(a)tomh.us>] [vx5] Support full charset (ASCII). Fixes #292 [Tom Hayward <tom(a)tomh.us>] [id31a] set used bit when creating new memory, clear when deleting. Fixes #269 [Tom Hayward <tom(a)tomh.us>] Support PyGTK < 2.22 in bank edit. Fixes #231 [Tom Hayward <tom(a)tomh.us>] [d710] [v71] [d72] Fix tone list (not all tones are supported). Fixes #212 [Dan Smith <dsmith(a)danplanet.com>] [vx7] Fix setting memory power levels on 220MHz band Fixes #214 [Dan Smith <dsmith(a)danplanet.com>] fips: Pennsylvania FIPS code was wrong. #117 [Marco Filippi <iz3gme.marco(a)gmail.com>] Consider lower bound frequency of each valid_band as valid Fix bug #181 [Tom Hayward <tom(a)tomh.us>] tmd700: allow 8-char names. Fixes #176 [Dan Smith <dsmith(a)danplanet.com>] Fix the "blind deletion" problem, as well as properly direct copy/paste Fixes #172 [David Griffith <dave(a)661.org>] Bug #155 fix: VX-7 1.25m power levels [David Griffith <dave(a)661.org>] New INSTALL and README files Fixes #122 [Tom Hayward <tom(a)tomh.us>] thd72: only use hardware flow on OS X. Fixes #166 [Marco Filippi <iz3gme.marco(a)gmail.com>] [FT817] Tone freq not set correctly Same as #88 for FT857, to avoid code duplication fix code have been moved from ft857 to its ancestor class Fix bug #163 [Tom Hayward <tom(a)tomh.us>] Fix Mac .app so paths with spaces work. Fixes Bug #145 Full log: [...truncated 1233 lines...] test_copy_all (tests.TestCase_QYTKT8900D) Testing QYT KT8900D copy all ... ok test_detect (tests.TestCase_QYTKT8900D) Testing QYT KT8900D detect ... ok test_edges (tests.TestCase_QYTKT8900D) Testing QYT KT8900D edges ... ok test_settings (tests.TestCase_QYTKT8900D) Testing QYT KT8900D settings ... ok test_banks (tests.TestCase_IcomICT70) Testing Icom IC-T70 banks ... ok test_brute_force (tests.TestCase_IcomICT70) Testing Icom IC-T70 brute force ... ok test_clone (tests.TestCase_IcomICT70) Testing Icom IC-T70 clone ... ok test_copy_all (tests.TestCase_IcomICT70) Testing Icom IC-T70 copy all ... ok test_detect (tests.TestCase_IcomICT70) Testing Icom IC-T70 detect ... ok test_edges (tests.TestCase_IcomICT70) Testing Icom IC-T70 edges ... ok test_settings (tests.TestCase_IcomICT70) Testing Icom IC-T70 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 brute force ... ok test_clone (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 clone ... ok test_copy_all (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 copy all ... ok test_detect (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 detect ... ok test_edges (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 edges ... ok test_settings (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 settings ... ok test_banks (tests.TestCase_RetevisRB85) Testing Retevis RB85 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRB85) Testing Retevis RB85 brute force ... ok test_clone (tests.TestCase_RetevisRB85) Testing Retevis RB85 clone ... ok test_copy_all (tests.TestCase_RetevisRB85) Testing Retevis RB85 copy all ... ok test_detect (tests.TestCase_RetevisRB85) Testing Retevis RB85 detect ... ok test_edges (tests.TestCase_RetevisRB85) Testing Retevis RB85 edges ... ok test_settings (tests.TestCase_RetevisRB85) Testing Retevis RB85 settings ... ok test_banks (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P brute force ... ok test_clone (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P clone ... ok test_copy_all (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P copy all ... ok test_detect (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P detect ... ok test_edges (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P edges ... ok test_settings (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P settings ... ok test_banks (tests.TestCase_RetevisRT95) Testing Retevis RT95 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT95) Testing Retevis RT95 brute force ... ok test_clone (tests.TestCase_RetevisRT95) Testing Retevis RT95 clone ... ok test_copy_all (tests.TestCase_RetevisRT95) Testing Retevis RT95 copy all ... ok test_detect (tests.TestCase_RetevisRT95) Testing Retevis RT95 detect ... ok test_edges (tests.TestCase_RetevisRT95) Testing Retevis RT95 edges ... ok test_settings (tests.TestCase_RetevisRT95) Testing Retevis RT95 settings ... ok test_banks (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D banks ... ok test_brute_force (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D brute force ... ok test_clone (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D clone ... ok test_copy_all (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D copy all ... ok test_detect (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D detect ... ok test_edges (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D edges ... ok test_settings (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D settings ... ok test_banks (tests.TestCase_IcomICT7H) Testing Icom IC-T7H banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICT7H) Testing Icom IC-T7H brute force ... ok test_clone (tests.TestCase_IcomICT7H) Testing Icom IC-T7H clone ... ok test_copy_all (tests.TestCase_IcomICT7H) Testing Icom IC-T7H copy all ... ok test_detect (tests.TestCase_IcomICT7H) Testing Icom IC-T7H detect ... ok test_edges (tests.TestCase_IcomICT7H) Testing Icom IC-T7H edges ... ok test_settings (tests.TestCase_IcomICT7H) Testing Icom IC-T7H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G banks ... ok test_brute_force (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G brute force ... ok test_clone (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G clone ... ok test_copy_all (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G copy all ... ok test_detect (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G detect ... ok test_edges (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G edges ... ok test_settings (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G settings ... ok test_banks (tests.TestCase_QuanshengTGUV2) Testing Quansheng TG-UV2+ banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_QuanshengTGUV2) Testing Quansheng TG-UV2+ brute force ... ok test_clone (tests.TestCase_QuanshengTGUV2) Testing Quansheng TG-UV2+ clone ... ok test_copy_all (tests.TestCase_QuanshengTGUV2) Testing Quansheng TG-UV2+ copy all ... ok test_detect (tests.TestCase_QuanshengTGUV2) Testing Quansheng TG-UV2+ detect ... ok test_edges (tests.TestCase_QuanshengTGUV2) Testing Quansheng TG-UV2+ edges ... ok test_settings (tests.TestCase_QuanshengTGUV2) Testing Quansheng TG-UV2+ settings ... ok test_banks (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 banks ... ok test_brute_force (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 brute force ... ok test_clone (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 clone ... ok test_copy_all (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 copy all ... ok test_detect (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 detect ... ok test_edges (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 edges ... ok test_settings (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 settings ... ok test_banks (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R brute force ... ok test_clone (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R clone ... ok test_copy_all (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R copy all ... ok test_detect (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R detect ... ok test_edges (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R edges ... ok test_settings (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R settings ... ok test_banks (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M brute force ... ok test_clone (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M clone ... ok test_copy_all (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M copy all ... ok test_detect (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M detect ... ok test_edges (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M edges ... ok test_settings (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 brute force ... ok test_clone (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 clone ... ok test_copy_all (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 copy all ... ok test_detect (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 detect ... ok test_edges (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 edges ... ok test_settings (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_RetevisRT1) Testing Retevis RT1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT1) Testing Retevis RT1 brute force ... ok test_clone (tests.TestCase_RetevisRT1) Testing Retevis RT1 clone ... ok test_copy_all (tests.TestCase_RetevisRT1) Testing Retevis RT1 copy all ... ok test_detect (tests.TestCase_RetevisRT1) Testing Retevis RT1 detect ... ok test_edges (tests.TestCase_RetevisRT1) Testing Retevis RT1 edges ... ok test_settings (tests.TestCase_RetevisRT1) Testing Retevis RT1 settings ... ok test_banks (tests.TestCase_RuggedRH5RV2) Testing Rugged RH5R-V2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RuggedRH5RV2) Testing Rugged RH5R-V2 brute force ... ok test_clone (tests.TestCase_RuggedRH5RV2) Testing Rugged RH5R-V2 clone ... ok test_copy_all (tests.TestCase_RuggedRH5RV2) Testing Rugged RH5R-V2 copy all ... ok test_detect (tests.TestCase_RuggedRH5RV2) Testing Rugged RH5R-V2 detect ... ok test_edges (tests.TestCase_RuggedRH5RV2) Testing Rugged RH5R-V2 edges ... ok test_settings (tests.TestCase_RuggedRH5RV2) Testing Rugged RH5R-V2 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M brute force ... ok test_clone (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M clone ... ok test_copy_all (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M copy all ... ok test_detect (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M detect ... ok test_edges (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M edges ... ok test_settings (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M settings ... ok test_banks (tests.TestCase_IcomICT8A) Testing Icom IC-T8A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICT8A) Testing Icom IC-T8A brute force ... ok test_clone (tests.TestCase_IcomICT8A) Testing Icom IC-T8A clone ... ok test_copy_all (tests.TestCase_IcomICT8A) Testing Icom IC-T8A copy all ... ok test_detect (tests.TestCase_IcomICT8A) Testing Icom IC-T8A detect ... ok test_edges (tests.TestCase_IcomICT8A) Testing Icom IC-T8A edges ... ok test_settings (tests.TestCase_IcomICT8A) Testing Icom IC-T8A settings ... skipped 'Settings not supported' test_banks (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 brute force ... ok test_clone (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 clone ... ok test_copy_all (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 copy all ... ok test_detect (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 detect ... ok test_edges (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 edges ... ok test_settings (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 settings ... ok test_banks (tests.TestCase_BTECHFRSB1) Testing BTECH FRS-B1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHFRSB1) Testing BTECH FRS-B1 brute force ... ok test_clone (tests.TestCase_BTECHFRSB1) Testing BTECH FRS-B1 clone ... ok test_copy_all (tests.TestCase_BTECHFRSB1) Testing BTECH FRS-B1 copy all ... ok test_detect (tests.TestCase_BTECHFRSB1) Testing BTECH FRS-B1 detect ... ok test_edges (tests.TestCase_BTECHFRSB1) Testing BTECH FRS-B1 edges ... skipped 'No mutable memory locations found' test_settings (tests.TestCase_BTECHFRSB1) Testing BTECH FRS-B1 settings ... ok test_banks (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M brute force ... ok test_clone (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M clone ... ok test_copy_all (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M copy all ... ok test_detect (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M detect ... ok test_edges (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M edges ... ok test_settings (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 brute force ... ok test_clone (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 clone ... ok test_copy_all (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 copy all ... ok test_detect (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 detect ... ok test_edges (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 edges ... ok test_settings (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 settings ... ok test_banks (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus brute force ... ok test_clone (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus clone ... ok test_copy_all (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus copy all ... ok test_detect (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus detect ... ok test_edges (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus edges ... ok test_settings (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus settings ... ok test_banks (tests.TestCase_RetevisRT16) Testing Retevis RT16 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT16) Testing Retevis RT16 brute force ... ok test_clone (tests.TestCase_RetevisRT16) Testing Retevis RT16 clone ... ok test_copy_all (tests.TestCase_RetevisRT16) Testing Retevis RT16 copy all ... ok test_detect (tests.TestCase_RetevisRT16) Testing Retevis RT16 detect ... ok test_edges (tests.TestCase_RetevisRT16) Testing Retevis RT16 edges ... skipped 'No mutable memory locations found' test_settings (tests.TestCase_RetevisRT16) Testing Retevis RT16 settings ... ok test_banks (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 banks ... ok test_brute_force (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 brute force ... ok test_clone (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 clone ... ok test_copy_all (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 copy all ... ok test_detect (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 detect ... ok test_edges (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 edges ... ok test_settings (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 settings ... ok test_banks (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A brute force ... ok test_clone (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A clone ... ok test_copy_all (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A copy all ... ok test_detect (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A detect ... ok test_edges (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A edges ... ok test_settings (tests.TestCase_TDXoneTDQ8A) Testing TDXone TD-Q8A settings ... ok test_banks (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 brute force ... ok test_clone (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 clone ... ok test_copy_all (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 copy all ... ok test_detect (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 detect ... ok test_edges (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 edges ... ok test_settings (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 settings ... ok test_banks (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 banks ... ok test_brute_force (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 brute force ... ok test_clone (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 clone ... ok test_copy_all (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 copy all ... ok test_detect (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 detect ... ok test_edges (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 edges ... ok test_settings (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 banks ... ok test_brute_force (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 brute force ... ok test_clone (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 clone ... ok test_copy_all (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 copy all ... ok test_detect (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 detect ... ok test_edges (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 edges ... ok test_settings (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 settings ... ok test_banks (tests.TestCase_RadioddityR2) Testing Radioddity R2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RadioddityR2) Testing Radioddity R2 brute force ... ok test_clone (tests.TestCase_RadioddityR2) Testing Radioddity R2 clone ... ok test_copy_all (tests.TestCase_RadioddityR2) Testing Radioddity R2 copy all ... ok test_detect (tests.TestCase_RadioddityR2) Testing Radioddity R2 detect ... ok test_edges (tests.TestCase_RadioddityR2) Testing Radioddity R2 edges ... ok test_settings (tests.TestCase_RadioddityR2) Testing Radioddity R2 settings ... ok test_banks (tests.TestCase_CRTMicronUV) Testing CRT Micron UV banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_CRTMicronUV) Testing CRT Micron UV brute force ... ok test_clone (tests.TestCase_CRTMicronUV) Testing CRT Micron UV clone ... ok test_copy_all (tests.TestCase_CRTMicronUV) Testing CRT Micron UV copy all ... ok test_detect (tests.TestCase_CRTMicronUV) Testing CRT Micron UV detect ... ok test_edges (tests.TestCase_CRTMicronUV) Testing CRT Micron UV edges ... ok test_settings (tests.TestCase_CRTMicronUV) Testing CRT Micron UV settings ... ok test_banks (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 brute force ... ok test_clone (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 clone ... ok test_copy_all (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 copy all ... ok test_detect (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 detect ... ok test_edges (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 edges ... ok test_settings (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 settings ... ok test_banks (tests.TestCase_RetevisRT21) Testing Retevis RT21 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT21) Testing Retevis RT21 brute force ... ok test_clone (tests.TestCase_RetevisRT21) Testing Retevis RT21 clone ... ok test_copy_all (tests.TestCase_RetevisRT21) Testing Retevis RT21 copy all ... ok test_detect (tests.TestCase_RetevisRT21) Testing Retevis RT21 detect ... ok test_edges (tests.TestCase_RetevisRT21) Testing Retevis RT21 edges ... ok test_settings (tests.TestCase_RetevisRT21) Testing Retevis RT21 settings ... ok test_banks (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 brute force ... ok test_clone (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 clone ... ok test_copy_all (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 copy all ... ok test_detect (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 detect ... ok test_edges (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 edges ... ok test_settings (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 settings ... ok test_banks (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 banks ... ok test_brute_force (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 brute force ... ok test_clone (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 clone ... ok test_copy_all (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 copy all ... ok test_detect (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 detect ... ok test_edges (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 edges ... ok test_settings (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_TYTTH350) Testing TYT TH-350 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTH350) Testing TYT TH-350 brute force ... ok test_clone (tests.TestCase_TYTTH350) Testing TYT TH-350 clone ... ok test_copy_all (tests.TestCase_TYTTH350) Testing TYT TH-350 copy all ... ok test_detect (tests.TestCase_TYTTH350) Testing TYT TH-350 detect ... ok test_edges (tests.TestCase_TYTTH350) Testing TYT TH-350 edges ... ok test_settings (tests.TestCase_TYTTH350) Testing TYT TH-350 settings ... ok test_banks (tests.TestCase_IcomICW32A) Testing Icom IC-W32A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICW32A) Testing Icom IC-W32A brute force ... ok test_clone (tests.TestCase_IcomICW32A) Testing Icom IC-W32A clone ... ok test_copy_all (tests.TestCase_IcomICW32A) Testing Icom IC-W32A copy all ... ok test_detect (tests.TestCase_IcomICW32A) Testing Icom IC-W32A detect ... ok test_edges (tests.TestCase_IcomICW32A) Testing Icom IC-W32A edges ... ok test_settings (tests.TestCase_IcomICW32A) Testing Icom IC-W32A settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D banks ... ok test_brute_force (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D brute force ... ok test_clone (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D clone ... ok test_copy_all (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D copy all ... ok test_detect (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D detect ... ok test_edges (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D edges ... ok test_settings (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D settings ... ok test_banks (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 brute force ... ok test_clone (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 clone ... ok test_copy_all (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 copy all ... ok test_detect (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 detect ... ok test_edges (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 edges ... ok test_settings (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 settings ... ok test_banks (tests.TestCase_RadioddityUV5G) Testing Radioddity UV-5G banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RadioddityUV5G) Testing Radioddity UV-5G brute force ... ok test_clone (tests.TestCase_RadioddityUV5G) Testing Radioddity UV-5G clone ... ok test_copy_all (tests.TestCase_RadioddityUV5G) Testing Radioddity UV-5G copy all ... ok test_detect (tests.TestCase_RadioddityUV5G) Testing Radioddity UV-5G detect ... ok test_edges (tests.TestCase_RadioddityUV5G) Testing Radioddity UV-5G edges ... ok test_settings (tests.TestCase_RadioddityUV5G) Testing Radioddity UV-5G settings ... ok test_banks (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A brute force ... ok test_clone (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A clone ... ok test_copy_all (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A copy all ... ok test_detect (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A detect ... ok test_edges (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A edges ... ok test_settings (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A settings ... ok test_banks (tests.TestCase_BTECHGMRSV2) Testing BTECH GMRS-V2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHGMRSV2) Testing BTECH GMRS-V2 brute force ... ok test_clone (tests.TestCase_BTECHGMRSV2) Testing BTECH GMRS-V2 clone ... ok test_copy_all (tests.TestCase_BTECHGMRSV2) Testing BTECH GMRS-V2 copy all ... ok test_detect (tests.TestCase_BTECHGMRSV2) Testing BTECH GMRS-V2 detect ... ok test_edges (tests.TestCase_BTECHGMRSV2) Testing BTECH GMRS-V2 edges ... ok test_settings (tests.TestCase_BTECHGMRSV2) Testing BTECH GMRS-V2 settings ... ok test_banks (tests.TestCase_RetevisRT22) Testing Retevis RT22 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT22) Testing Retevis RT22 brute force ... ok test_clone (tests.TestCase_RetevisRT22) Testing Retevis RT22 clone ... ok test_copy_all (tests.TestCase_RetevisRT22) Testing Retevis RT22 copy all ... ok test_detect (tests.TestCase_RetevisRT22) Testing Retevis RT22 detect ... ok test_edges (tests.TestCase_RetevisRT22) Testing Retevis RT22 edges ... ok test_settings (tests.TestCase_RetevisRT22) Testing Retevis RT22 settings ... ok test_banks (tests.TestCase_IcomICW32E) Testing Icom IC-W32E banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICW32E) Testing Icom IC-W32E brute force ... ok test_clone (tests.TestCase_IcomICW32E) Testing Icom IC-W32E clone ... ok test_copy_all (tests.TestCase_IcomICW32E) Testing Icom IC-W32E copy all ... ok test_detect (tests.TestCase_IcomICW32E) Testing Icom IC-W32E detect ... ok test_edges (tests.TestCase_IcomICW32E) Testing Icom IC-W32E edges ... ok test_settings (tests.TestCase_IcomICW32E) Testing Icom IC-W32E settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R banks ... ok test_brute_force (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R brute force ... ok test_clone (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R clone ... ok test_copy_all (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R copy all ... ok test_detect (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R detect ... ok test_edges (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R edges ... ok test_settings (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R settings ... ok test_banks (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG brute force ... ok test_clone (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG clone ... ok test_copy_all (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG copy all ... ok test_detect (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG detect ... ok test_edges (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG edges ... ok test_settings (tests.TestCase_AlincoDJG7EG) Testing Alinco DJ-G7EG settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 banks ... ok test_brute_force (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 brute force ... ok test_clone (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 clone ... ok test_copy_all (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 copy all ... ok test_detect (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 detect ... ok test_edges (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 edges ... ok test_settings (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 settings ... ok test_banks (tests.TestCase_RadtelT18) Testing Radtel T18 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RadtelT18) Testing Radtel T18 brute force ... ok test_clone (tests.TestCase_RadtelT18) Testing Radtel T18 clone ... ok test_copy_all (tests.TestCase_RadtelT18) Testing Radtel T18 copy all ... ok test_detect (tests.TestCase_RadtelT18) Testing Radtel T18 detect ... ok test_edges (tests.TestCase_RadtelT18) Testing Radtel T18 edges ... ok test_settings (tests.TestCase_RadtelT18) Testing Radtel T18 settings ... ok test_banks (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND brute force ... ok test_clone (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND clone ... ok test_copy_all (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND copy all ... ok test_detect (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND detect ... ok test_edges (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND edges ... ok test_settings (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND settings ... ok test_banks (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 brute force ... ok test_clone (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 clone ... ok test_copy_all (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 copy all ... ok test_detect (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 detect ... ok test_edges (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 edges ... skipped 'No mutable memory locations found' test_settings (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 settings ... ok test_banks (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B brute force ... ok test_clone (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B clone ... ok test_copy_all (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B copy all ... ok test_detect (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B detect ... ok test_edges (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B edges ... ok test_settings (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B settings ... ok test_banks (tests.TestCase_RetevisRT22FRS) Testing Retevis RT22FRS banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT22FRS) Testing Retevis RT22FRS brute force ... ok test_clone (tests.TestCase_RetevisRT22FRS) Testing Retevis RT22FRS clone ... ok test_copy_all (tests.TestCase_RetevisRT22FRS) Testing Retevis RT22FRS copy all ... ok test_detect (tests.TestCase_RetevisRT22FRS) Testing Retevis RT22FRS detect ... ok test_edges (tests.TestCase_RetevisRT22FRS) Testing Retevis RT22FRS edges ... ok test_settings (tests.TestCase_RetevisRT22FRS) Testing Retevis RT22FRS settings ... ok test_banks (tests.TestCase_TYTTH7800) Testing TYT TH-7800 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTH7800) Testing TYT TH-7800 brute force ... ok test_clone (tests.TestCase_TYTTH7800) Testing TYT TH-7800 clone ... ok test_copy_all (tests.TestCase_TYTTH7800) Testing TYT TH-7800 copy all ... ok test_detect (tests.TestCase_TYTTH7800) Testing TYT TH-7800 detect ... ok test_edges (tests.TestCase_TYTTH7800) Testing TYT TH-7800 edges ... ok test_settings (tests.TestCase_TYTTH7800) Testing TYT TH-7800 settings ... ok test_banks (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M brute force ... ok test_clone (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M clone ... ok test_copy_all (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M copy all ... ok test_detect (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M detect ... ok test_edges (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M edges ... ok test_settings (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode brute force ... ok test_clone (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode clone ... ok test_copy_all (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode copy all ... ok test_detect (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode detect ... ok test_edges (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode edges ... ok test_settings (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode settings ... ok test_banks (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 brute force ... ok test_clone (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 clone ... ok test_copy_all (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 copy all ... ok test_detect (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 detect ... ok test_edges (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 edges ... ok test_settings (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 settings ... ok test_banks (tests.TestCase_RetevisRA85) Testing Retevis RA85 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRA85) Testing Retevis RA85 brute force ... ok test_clone (tests.TestCase_RetevisRA85) Testing Retevis RA85 clone ... ok test_copy_all (tests.TestCase_RetevisRA85) Testing Retevis RA85 copy all ... ok test_detect (tests.TestCase_RetevisRA85) Testing Retevis RA85 detect ... ok test_edges (tests.TestCase_RetevisRA85) Testing Retevis RA85 edges ... ok test_settings (tests.TestCase_RetevisRA85) Testing Retevis RA85 settings ... ok test_banks (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) brute force ... ok test_clone (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) clone ... ok test_copy_all (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) copy all ... ok test_detect (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) detect ... ok test_edges (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) edges ... ok test_settings (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) settings ... ok test_banks (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 banks ... ok test_brute_force (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 brute force ... ok test_clone (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 clone ... ok test_copy_all (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 copy all ... ok test_detect (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 detect ... ok test_edges (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 edges ... ok test_settings (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_RetevisRT22S) Testing Retevis RT22S banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT22S) Testing Retevis RT22S brute force ... ok test_clone (tests.TestCase_RetevisRT22S) Testing Retevis RT22S clone ... ok test_copy_all (tests.TestCase_RetevisRT22S) Testing Retevis RT22S copy all ... ok test_detect (tests.TestCase_RetevisRT22S) Testing Retevis RT22S detect ... ok test_edges (tests.TestCase_RetevisRT22S) Testing Retevis RT22S edges ... skipped 'No mutable memory locations found' test_settings (tests.TestCase_RetevisRT22S) Testing Retevis RT22S settings ... ok test_banks (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R banks ... ok test_brute_force (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R brute force ... ok test_clone (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R clone ... ok test_copy_all (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R copy all ... ok test_detect (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R detect ... ok test_edges (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R edges ... ok test_settings (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R settings ... ok test_banks (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B brute force ... ok test_clone (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B clone ... ok test_copy_all (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B copy all ... ok test_detect (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B detect ... ok test_edges (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B edges ... ok test_settings (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B settings ... ok test_banks (tests.TestCase_IcomID31A) Testing Icom ID-31A banks ... ok test_brute_force (tests.TestCase_IcomID31A) Testing Icom ID-31A brute force ... ok test_clone (tests.TestCase_IcomID31A) Testing Icom ID-31A clone ... ok test_copy_all (tests.TestCase_IcomID31A) Testing Icom ID-31A copy all ... ok test_detect (tests.TestCase_IcomID31A) Testing Icom ID-31A detect ... ok test_edges (tests.TestCase_IcomID31A) Testing Icom ID-31A edges ... ok test_settings (tests.TestCase_IcomID31A) Testing Icom ID-31A settings ... ok test_banks (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 brute force ... ok test_clone (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 clone ... ok test_copy_all (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 copy all ... ok test_detect (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 detect ... ok test_edges (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 edges ... ok test_settings (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 settings ... ok test_banks (tests.TestCase_RetevisRB17) Testing Retevis RB17 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRB17) Testing Retevis RB17 brute force ... ok test_clone (tests.TestCase_RetevisRB17) Testing Retevis RB17 clone ... ok test_copy_all (tests.TestCase_RetevisRB17) Testing Retevis RB17 copy all ... ok test_detect (tests.TestCase_RetevisRB17) Testing Retevis RB17 detect ... ok test_edges (tests.TestCase_RetevisRB17) Testing Retevis RB17 edges ... skipped 'No mutable memory locations found' test_settings (tests.TestCase_RetevisRB17) Testing Retevis RB17 settings ... ok test_banks (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode brute force ... ok test_clone (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode clone ... ok test_copy_all (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode copy all ... ok test_detect (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode detect ... ok test_edges (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode edges ... ok test_settings (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode settings ... ok test_banks (tests.TestCase_TYTTH9800) Testing TYT TH-9800 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTH9800) Testing TYT TH-9800 brute force ... ok test_clone (tests.TestCase_TYTTH9800) Testing TYT TH-9800 clone ... ok test_copy_all (tests.TestCase_TYTTH9800) Testing TYT TH-9800 copy all ... ok test_detect (tests.TestCase_TYTTH9800) Testing TYT TH-9800 detect ... ok test_edges (tests.TestCase_TYTTH9800) Testing TYT TH-9800 edges ... ok test_settings (tests.TestCase_TYTTH9800) Testing TYT TH-9800 settings ... ok test_banks (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 brute force ... ok test_clone (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 clone ... ok test_copy_all (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 copy all ... ok test_detect (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 detect ... ok test_edges (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 edges ... ok test_settings (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 settings ... ok test_banks (tests.TestCase_RetevisRT23) Testing Retevis RT23 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT23) Testing Retevis RT23 brute force ... ok test_clone (tests.TestCase_RetevisRT23) Testing Retevis RT23 clone ... ok test_copy_all (tests.TestCase_RetevisRT23) Testing Retevis RT23 copy all ... ok test_detect (tests.TestCase_RetevisRT23) Testing Retevis RT23 detect ... ok test_edges (tests.TestCase_RetevisRT23) Testing Retevis RT23 edges ... ok test_settings (tests.TestCase_RetevisRT23) Testing Retevis RT23 settings ... ok test_banks (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D brute force ... ok test_clone (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D clone ... ok test_copy_all (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D copy all ... ok test_detect (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D detect ... ok test_edges (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D edges ... ok test_settings (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D settings ... ok test_banks (tests.TestCase_IcomIC208H) Testing Icom IC-208H banks ... ok test_brute_force (tests.TestCase_IcomIC208H) Testing Icom IC-208H brute force ... ok test_clone (tests.TestCase_IcomIC208H) Testing Icom IC-208H clone ... ok test_copy_all (tests.TestCase_IcomIC208H) Testing Icom IC-208H copy all ... ok test_detect (tests.TestCase_IcomIC208H) Testing Icom IC-208H detect ... ok test_edges (tests.TestCase_IcomIC208H) Testing Icom IC-208H edges ... ok test_settings (tests.TestCase_IcomIC208H) Testing Icom IC-208H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 brute force ... ok test_clone (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 clone ... ok test_copy_all (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 copy all ... ok test_detect (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 detect ... ok test_edges (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 edges ... ok test_settings (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 settings ... ok test_banks (tests.TestCase_RetevisRB17A) Testing Retevis RB17A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRB17A) Testing Retevis RB17A brute force ... ok test_clone (tests.TestCase_RetevisRB17A) Testing Retevis RB17A clone ... ok test_copy_all (tests.TestCase_RetevisRB17A) Testing Retevis RB17A copy all ... ok test_detect (tests.TestCase_RetevisRB17A) Testing Retevis RB17A detect ... ok test_edges (tests.TestCase_RetevisRB17A) Testing Retevis RB17A edges ... skipped 'No mutable memory locations found' test_settings (tests.TestCase_RetevisRB17A) Testing Retevis RB17A settings ... ok test_banks (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR banks ... ok test_brute_force (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR brute force ... ok test_clone (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR clone ... ok test_copy_all (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR copy all ... ok test_detect (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR detect ... ok test_edges (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR edges ... ok test_settings (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR settings ... ok test_banks (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode brute force ... ok test_clone (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode clone ... ok test_copy_all (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode copy all ... ok test_detect (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode detect ... ok test_edges (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode edges ... ok test_settings (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode settings ... ok test_banks (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 brute force ... ok test_clone (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 clone ... ok test_copy_all (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 copy all ... ok test_detect (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 detect ... ok test_edges (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 edges ... ok test_settings (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 brute force ... ok test_clone (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 clone ... ok test_copy_all (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 copy all ... ok test_detect (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 detect ... ok test_edges (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 edges ... ok test_settings (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 settings ... ok test_banks (tests.TestCase_RetevisRT26) Testing Retevis RT26 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT26) Testing Retevis RT26 brute force ... ok test_clone (tests.TestCase_RetevisRT26) Testing Retevis RT26 clone ... ok test_copy_all (tests.TestCase_RetevisRT26) Testing Retevis RT26 copy all ... ok test_detect (tests.TestCase_RetevisRT26) Testing Retevis RT26 detect ... ok test_edges (tests.TestCase_RetevisRT26) Testing Retevis RT26 edges ... ok test_settings (tests.TestCase_RetevisRT26) Testing Retevis RT26 settings ... ok test_banks (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H brute force ... ok test_clone (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H clone ... ok test_copy_all (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H copy all ... ok test_detect (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H detect ... ok test_edges (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H edges ... ok test_settings (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 brute force ... ok test_clone (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 clone ... ok test_copy_all (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 copy all ... ok test_detect (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 detect ... ok test_edges (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 edges ... ok test_settings (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 settings ... ok test_banks (tests.TestCase_RetevisRB17P) Testing Retevis RB17P banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRB17P) Testing Retevis RB17P brute force ... ok test_clone (tests.TestCase_RetevisRB17P) Testing Retevis RB17P clone ... ok test_copy_all (tests.TestCase_RetevisRB17P) Testing Retevis RB17P copy all ... ok test_detect (tests.TestCase_RetevisRB17P) Testing Retevis RB17P detect ... ok test_edges (tests.TestCase_RetevisRB17P) Testing Retevis RB17P edges ... skipped 'No mutable memory locations found' test_settings (tests.TestCase_RetevisRB17P) Testing Retevis RB17P settings ... ok test_banks (tests.TestCase_IcomID51) Testing Icom ID-51 banks ... ok test_brute_force (tests.TestCase_IcomID51) Testing Icom ID-51 brute force ... ok test_clone (tests.TestCase_IcomID51) Testing Icom ID-51 clone ... ok test_copy_all (tests.TestCase_IcomID51) Testing Icom ID-51 copy all ... ok test_detect (tests.TestCase_IcomID51) Testing Icom ID-51 detect ... ok test_edges (tests.TestCase_IcomID51) Testing Icom ID-51 edges ... ok test_settings (tests.TestCase_IcomID51) Testing Icom ID-51 settings ... ok test_banks (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode brute force ... ok test_clone (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode clone ... ok test_copy_all (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode copy all ... ok test_detect (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode detect ... ok test_edges (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode edges ... ok test_settings (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode settings ... ok test_banks (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R brute force ... ok test_clone (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R clone ... ok test_copy_all (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R copy all ... ok test_detect (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R detect ... ok test_edges (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R edges ... ok test_settings (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R settings ... skipped 'Settings not supported' test_banks (tests.TestCase_RetevisRT622) Testing Retevis RT622 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT622) Testing Retevis RT622 brute force ... ok test_clone (tests.TestCase_RetevisRT622) Testing Retevis RT622 clone ... ok test_copy_all (tests.TestCase_RetevisRT622) Testing Retevis RT622 copy all ... ok test_detect (tests.TestCase_RetevisRT622) Testing Retevis RT622 detect ... ok test_edges (tests.TestCase_RetevisRT622) Testing Retevis RT622 edges ... ok test_settings (tests.TestCase_RetevisRT622) Testing Retevis RT622 settings ... ok test_banks (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) brute force ... ok test_clone (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) clone ... ok test_copy_all (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) copy all ... ok test_detect (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) detect ... ok test_edges (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) edges ... ok test_settings (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) settings ... ok test_banks (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 brute force ... ok test_clone (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 clone ... ok test_copy_all (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 copy all ... ok test_detect (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 detect ... ok test_edges (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 edges ... ok test_settings (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 settings ... ok test_banks (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H banks ... ok test_brute_force (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H brute force ... ok test_clone (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H clone ... ok test_copy_all (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H copy all ... ok test_detect (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H detect ... ok test_edges (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H edges ... ok test_settings (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H settings ... ok test_banks (tests.TestCase_RetevisRB17V) Testing Retevis RB17V banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRB17V) Testing Retevis RB17V brute force ... ok test_clone (tests.TestCase_RetevisRB17V) Testing Retevis RB17V clone ... ok test_copy_all (tests.TestCase_RetevisRB17V) Testing Retevis RB17V copy all ... ok test_detect (tests.TestCase_RetevisRB17V) Testing Retevis RB17V detect ... ok test_edges (tests.TestCase_RetevisRB17V) Testing Retevis RB17V edges ... skipped 'No mutable memory locations found' test_settings (tests.TestCase_RetevisRB17V) Testing Retevis RB17V settings ... ok test_banks (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 brute force ... ok test_clone (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 clone ... ok test_copy_all (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 copy all ... ok test_detect (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 detect ... ok test_edges (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 edges ... ok test_settings (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 settings ... ok test_banks (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE banks ... ok test_brute_force (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE brute force ... ok test_clone (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE clone ... ok test_copy_all (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE copy all ... ok test_detect (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE detect ... ok test_edges (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE edges ... ok test_settings (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE settings ... ok test_banks (tests.TestCase_LUITONLT580UHF) Testing LUITON LT-580_UHF banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_LUITONLT580UHF) Testing LUITON LT-580_UHF brute force ... ok test_clone (tests.TestCase_LUITONLT580UHF) Testing LUITON LT-580_UHF clone ... ok test_copy_all (tests.TestCase_LUITONLT580UHF) Testing LUITON LT-580_UHF copy all ... ok test_detect (tests.TestCase_LUITONLT580UHF) Testing LUITON LT-580_UHF detect ... ok test_edges (tests.TestCase_LUITONLT580UHF) Testing LUITON LT-580_UHF edges ... ok test_settings (tests.TestCase_LUITONLT580UHF) Testing LUITON LT-580_UHF settings ... ok test_banks (tests.TestCase_RetevisRT668) Testing Retevis RT668 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT668) Testing Retevis RT668 brute force ... ok test_clone (tests.TestCase_RetevisRT668) Testing Retevis RT668 clone ... ok test_copy_all (tests.TestCase_RetevisRT668) Testing Retevis RT668 copy all ... ok test_detect (tests.TestCase_RetevisRT668) Testing Retevis RT668 detect ... ok test_edges (tests.TestCase_RetevisRT668) Testing Retevis RT668 edges ... skipped 'No mutable memory locations found' test_settings (tests.TestCase_RetevisRT668) Testing Retevis RT668 settings ... ok test_banks (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus banks ... ok test_brute_force (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus brute force ... ok test_clone (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus clone ... ok test_copy_all (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus copy all ... ok test_detect (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus detect ... ok test_edges (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus edges ... ok test_settings (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus settings ... ok test_banks (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 brute force ... ok test_clone (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 clone ... ok test_copy_all (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 copy all ... ok test_detect (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 detect ... ok test_edges (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 edges ... ok test_settings (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 settings ... ok test_banks (tests.TestCase_TYTTHUV88) Testing TYT TH-UV88 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUV88) Testing TYT TH-UV88 brute force ... ok test_clone (tests.TestCase_TYTTHUV88) Testing TYT TH-UV88 clone ... ok test_copy_all (tests.TestCase_TYTTHUV88) Testing TYT TH-UV88 copy all ... ok test_detect (tests.TestCase_TYTTHUV88) Testing TYT TH-UV88 detect ... ok test_edges (tests.TestCase_TYTTHUV88) Testing TYT TH-UV88 edges ... ok test_settings (tests.TestCase_TYTTHUV88) Testing TYT TH-UV88 settings ... ok test_banks (tests.TestCase_RetevisRB18) Testing Retevis RB18 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRB18) Testing Retevis RB18 brute force ... ok test_clone (tests.TestCase_RetevisRB18) Testing Retevis RB18 clone ... ok test_copy_all (tests.TestCase_RetevisRB18) Testing Retevis RB18 copy all ... ok test_detect (tests.TestCase_RetevisRB18) Testing Retevis RB18 detect ... ok test_edges (tests.TestCase_RetevisRB18) Testing Retevis RB18 edges ... skipped 'No mutable memory locations found' test_settings (tests.TestCase_RetevisRB18) Testing Retevis RB18 settings ... ok test_banks (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 banks ... ok test_brute_force (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 brute force ... ok test_clone (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 clone ... ok test_copy_all (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 copy all ... ok test_detect (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 detect ... ok test_edges (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 edges ... ok test_settings (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_LUITONLT580VHF) Testing LUITON LT-580_VHF banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_LUITONLT580VHF) Testing LUITON LT-580_VHF brute force ... ok test_clone (tests.TestCase_LUITONLT580VHF) Testing LUITON LT-580_VHF clone ... ok test_copy_all (tests.TestCase_LUITONLT580VHF) Testing LUITON LT-580_VHF copy all ... ok test_detect (tests.TestCase_LUITONLT580VHF) Testing LUITON LT-580_VHF detect ... ok test_edges (tests.TestCase_LUITONLT580VHF) Testing LUITON LT-580_VHF edges ... ok test_settings (tests.TestCase_LUITONLT580VHF) Testing LUITON LT-580_VHF settings ... ok test_banks (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 brute force ... ok test_clone (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 clone ... ok test_copy_all (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 copy all ... ok test_detect (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 detect ... ok test_edges (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 edges ... ok test_settings (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 settings ... ok test_banks (tests.TestCase_IcomID800H) Testing Icom ID-800H banks ... ok test_brute_force (tests.TestCase_IcomID800H) Testing Icom ID-800H brute force ... ok test_clone (tests.TestCase_IcomID800H) Testing Icom ID-800H clone ... ok test_copy_all (tests.TestCase_IcomID800H) Testing Icom ID-800H copy all ... ok test_detect (tests.TestCase_IcomID800H) Testing Icom ID-800H detect ... ok test_edges (tests.TestCase_IcomID800H) Testing Icom ID-800H edges ... ok test_settings (tests.TestCase_IcomID800H) Testing Icom ID-800H settings ... ok test_banks (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 brute force ... ok test_clone (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 clone ... ok test_copy_all (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 copy all ... ok test_detect (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 detect ... ok test_edges (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 edges ... ok test_settings (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R banks ... ok test_brute_force (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R brute force ... ok test_clone (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R clone ... ok test_copy_all (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R copy all ... ok test_detect (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R detect ... ok test_edges (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R edges ... ok test_settings (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R settings ... ok test_banks (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV brute force ... ok test_clone (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV clone ... ok test_copy_all (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV copy all ... ok test_detect (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV detect ... ok test_edges (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV edges ... ok test_settings (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV settings ... ok test_banks (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 brute force ... ok test_clone (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 clone ... ok test_copy_all (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 copy all ... ok test_detect (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 detect ... ok test_edges (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 edges ... ok test_settings (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 settings ... ok test_banks (tests.TestCase_IcomID880H) Testing Icom ID-880H banks ... ok test_brute_force (tests.TestCase_IcomID880H) Testing Icom ID-880H brute force ... ok test_clone (tests.TestCase_IcomID880H) Testing Icom ID-880H clone ... ok test_copy_all (tests.TestCase_IcomID880H) Testing Icom ID-880H copy all ... ok test_detect (tests.TestCase_IcomID880H) Testing Icom ID-880H detect ... ok test_edges (tests.TestCase_IcomID880H) Testing Icom ID-880H edges ... ok test_settings (tests.TestCase_IcomID880H) Testing Icom ID-880H settings ... ok test_banks (tests.TestCase_LeixenVV898) Testing Leixen VV-898 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_LeixenVV898) Testing Leixen VV-898 brute force ... ok test_clone (tests.TestCase_LeixenVV898) Testing Leixen VV-898 clone ... ok test_copy_all (tests.TestCase_LeixenVV898) Testing Leixen VV-898 copy all ... ok test_detect (tests.TestCase_LeixenVV898) Testing Leixen VV-898 detect ... ok test_edges (tests.TestCase_LeixenVV898) Testing Leixen VV-898 edges ... ok test_settings (tests.TestCase_LeixenVV898) Testing Leixen VV-898 settings ... ok test_banks (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M brute force ... ok test_clone (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M clone ... ok test_copy_all (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M copy all ... ok test_detect (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M detect ... ok test_edges (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M edges ... ok test_settings (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S brute force ... ok test_clone (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S clone ... ok test_copy_all (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S copy all ... ok test_detect (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S detect ... ok test_edges (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S edges ... ok test_settings (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S settings ... ok test_banks (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D banks ... ok test_brute_force (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D brute force ... ok test_clone (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D clone ... ok test_copy_all (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D copy all ... ok test_detect (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D detect ... ok test_edges (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D edges ... ok test_settings (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D settings ... ok test_banks (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M brute force ... ok test_clone (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M clone ... ok test_copy_all (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M copy all ... ok test_detect (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M detect ... ok test_edges (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M edges ... ok test_settings (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M settings ... ok ---------------------------------------------------------------------- Ran 1281 tests in 511.562s OK (skipped=194) struct memory { bbcd rx_freq[4]; bbcd tx_freq[4]; lbcd rx_tone[2]; lbcd tx_tone[2]; u8 unknown10:5, highpower:1, unknown11:2; u8 unknown20:4, narrow:1, unknown21:3; u8 unknown31:1, scanadd:1, unknown32:6; u8 unknown4; }; struct name { char name[7]; }; #seekto 0x0010; struct memory channels[128]; #seekto 0x08C0; struct name names[128]; #seekto 0x2020; struct memory vfo1; struct memory vfo2; style create: /chirp/.tox/style style installdeps: pep8==1.6.2, future style inst: /chirp/.tox/.tmp/package/1/chirp-0.3.0dev.zip style installed: DEPRECATION: Python 2.7 will reach the end of its life on January 1st, 2020. Please upgrade your Python as Python 2.7 won't be maintained after that date. A future version of pip will drop support for Python 2.7.,chirp==0.3.0.dev0,configparser==3.7.4,contextlib2==0.5.5,filelock==3.0.12,future==0.15.2,importlib-metadata==0.18,Mako==1.0.3,MarkupSafe==0.23,mercurial==3.7.3,packaging==19.0,pathlib2==2.3.4,pep8==1.6.2,pluggy==0.12.0,py==1.8.0,pygobject==3.20.0,pyparsing==2.4.0,pyserial==3.0.1,scandir==1.10.0,six==1.12.0,toml==0.10.0,tox==3.13.2,virtualenv==16.6.1,zipp==0.5.2 style run-test-pre: PYTHONHASHSEED='1024268242' style run-test: commands[0] | python ./tools/cpep8.py ___________________________________ summary ____________________________________ unit: commands succeeded driver: commands succeeded style: commands succeeded congratulations :) Email was triggered for: Success Sending email for trigger: Success

1 0

[chirp_devel] [PATCH] [TD-UV5R TriPower] TIDRADIO TD-UV-5R TriPower Incorrect Alias
by Jim Unroe 12 May '22

12 May '22

1 1

[chirp_devel] [PATCH] [TD-UV5R TriPower] TIDRADIO TD-UV-5R TriPower Incorrect Alias
by Jim Unroe 12 May '22

12 May '22

1 1

[chirp_devel] [PATCH] [GMRS-V2] New Model: Baofeng TEch GMRS-V2
by Jim Unroe 09 May '22

09 May '22

1 1

[chirp_devel] [PATCH 1 of 2] [GMRS-V1] Add Display and Edit Alarm Code Feature
by Jim Unroe 08 May '22

08 May '22

1 1

[chirp_devel] New driver for Abbree AR-F8
by Mark Leyden 08 May '22

08 May '22

Thoughts welcome!

2 6

[chirp_devel] [PATCH 1 of 2] [GMRS-V1] Fix PTT ID Delay (PTT-LT) Upper Limit Check
by Jim Unroe 07 May '22

07 May '22

2 2

Re: [chirp_devel] New driver for Radtel RT-490 and clones (fix #9665) (image + tests)
by angelof9 06 May '22

06 May '22

Here is the image binary file for RT-490. All tests are ok: > python .\tests\run_tests.py -d Radtel_RT-490 Radtel RT-490 Detect [1;32m PASSED:[0m All tests Radtel RT-490 Settings [1;32m PASSED:[0m All tests Radtel RT-490 Clone [1;32m PASSED:[0m All tests Radtel RT-490 Edges [1;32m PASSED:[0m All tests Radtel RT-490 BruteForce [1;32m PASSED:[0m All tests Radtel RT-490 CopyAll [1;32m PASSED:[0m All tests Radtel RT-490 Banks [1;32mSKIPPED:[0m Banks not supported----------------------------------------------------------------------Results: TOTAL : 7 FAILED : 0 SKIPPED: 1 PASSED : 6 CRASHED: 0 Sent with ProtonMail secure email. ------- Original Message ------- On Friday, May 6th, 2022 at 7:31 PM, angelof9 <angelof9(a)protonmail.com> wrote: > Hello, > Please find the patch for a new driver for Radtel RT-490 and its clones (8 at this moment). > Driver supports: - Radtel RT-490, - MMLradio 8629, - JJCC 8629, - Socotran JC8629, - Socotran FB8629, - Jianpai 8629, - Boristone 8RS, - Abbree AR869, - HamGeek HG590. > Support ALL official software features. > Plus these new features: - FM preset - Channel memory preset - Killswitch setup (+ can revive killed radios) - Bands settings for 4 bands ranges + tx on/off - Fixed issue of radio being corrupted with official software with custom (channel/ani) names - Included basic help for custom features - Disable radio identification string verification (good to recover from a bad state) > > Regards,Ao9. > > Sent with ProtonMail secure email.

1 0

[chirp_devel] Py3 live mode - understanding the intent
by Martin Cooper 29 Apr '22

29 Apr '22

This is really directed towards Dan, since I suspect he's the only one with answers. :-) In the py3 branch, it seems that the intent for live mode radios is to change the behaviour so that they act more like clone mode. That is, instead of changes being sent to the radio as soon as they're made, as with today's Chirp, nothing is sent to the radio until an Upload is done. I presume this was done to make the two modes appear more consistent. (It's confusing to existing users who expect instant changes, though, and will require clear documentation.) As part of the implementation, a LiveAdapter class is used, and that is a subclass of the Generic CSV driver. I'm guessing is that this is intended to enable the saving and loading of "images" for live mode radios, using CSV files as the file backing. After downloading from a live mode radio, saving does work, and produces a CSV file, but with a file extension of "img" rather than "csv". Due to that file extension, however, loading does _not_ work, because the image type detection code does not look for CSV-typed data. Also, immediately after a Download, the tab in the GUI shows a ".img" filename, and shows it as edited. It's unclear as to whether this is intended (because no file has been saved) or not (because no changes have actually been made to the memories that were just downloaded). Finally (for now), when running an Upload, all memories are written to the radio, regardless of whether or not they have been changed. This can be slow, since all memories in all banks are written. If I Download from the radio, change one memory, and then Upload to the radio, because of the way live mode radios work, it seems like it would make more sense to upload only the memory that has changed. This may get more complicated when dealing with "images" loaded from a file, though - or maybe not, since memories are also being read as they are being written. Before I dive in and look at making changes, it would be helpful to understand the thinking behind the approach, and the intent of how it should work, particularly in regard to the points mentioned above, but also in any other related regard. I do have a local change for writing only changed memories, but I'd like to have the big picture before going any further. Thanks, Martin. KD6YAM

2 2