[chirp_users] UV-6 programming
My UV 6 Baofeng will not respond to up load to chirp I have the right drivers loaded and the wire seem to go all the way in same wire is use for uv82 with no problem
On Thu, Oct 29, 2015 at 6:03 PM, slynchmob--- via chirp_users chirp_users@intrepid.danplanet.com wrote:
My UV 6 Baofeng will not respond to up load to chirp I have the right drivers loaded and the wire seem to go all the way in same wire is use for uv82 with no problem
Is your radio a UV-6 or UV-6R? CHIRP does not support the UV-6R. If you actually have a UV-6, does it work with the OEM software?
Jim KC9HI
Hi, Just a thought as my UV-5RC wouldn't up load from my laptop unless after I'd finished entering the frequencies etc. into Chirp I had to save the page and then X out that file on the screen (plain Chirp screen left on display) then click file, open and then click on the frequency file I'd saved then open, at this point all that I'd saved previously was back on the screen and then carry on the usual way to upload to the radio. Works on all my different rigs. Hope this was of use....
73, Richard de 5B4AJG
Sent from my iPhone
On 30 Oct 2015, at 00:03, slynchmob--- via chirp_users chirp_users@intrepid.danplanet.com wrote:
My UV 6 Baofeng will not respond to up load to chirp I have the right drivers loaded and the wire seem to go all the way in same wire is use for uv82 with no problem _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Before you started the process, did you initially create a CHIRP template by doing a Download from Radio.
CHIRP supports over 80 various models and requires a template to identify the type radio it will be programming.
Refer to (1.1) http://www.miklor.com/COM/UV_CHIRP.php
I hope this assists.
John
From: chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Richard Langmead Sent: Friday, October 30, 2015 4:04 AM To: slynchmob@aol.com; Discussion of CHIRP Subject: Re: [chirp_users] UV-6 programming
Hi,
Just a thought as my UV-5RC wouldn't up load from my laptop unless after I'd finished entering the frequencies etc. into Chirp I had to save the page and then X out that file on the screen (plain Chirp screen left on display) then click file, open and then click on the frequency file I'd saved then open, at this point all that I'd saved previously was back on the screen and then carry on the usual way to upload to the radio.
Works on all my different rigs.
Hope this was of use....
73, Richard de 5B4AJG
Sent from my iPhone
On 30 Oct 2015, at 00:03, slynchmob--- via chirp_users chirp_users@intrepid.danplanet.com wrote:
My UV 6 Baofeng will not respond to up load to chirp I have the right drivers loaded and the wire seem to go all the way in same wire is use for uv82 with no problem
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Every things looks good till I try to up load from radio then it shows that radio did not respond
-----Original Message----- From: John LaMartina JohnLa@usa.net To: 'Discussion of CHIRP' chirp_users@intrepid.danplanet.com Sent: Fri, Oct 30, 2015 11:45 am Subject: Re: [chirp_users] UV-6 programming
Before you started the process, did you initially create a CHIRP template by doing a Download from Radio. CHIRP supports over 80 various models and requires a template to identify the type radio it will be programming.
Refer to (1.1) http://www.miklor.com/COM/UV_CHIRP.php
I hope this assists.
John - http://www.miklor.com
From: chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Richard Langmead Sent: Friday, October 30, 2015 4:04 AM To: slynchmob@aol.com; Discussion of CHIRP Subject: Re: [chirp_users] UV-6 programming
Hi,
Just a thought as my UV-5RC wouldn't up load from my laptop unless after I'd finished entering the frequencies etc. into Chirp I had to save the page and then X out that file on the screen (plain Chirp screen left on display) then click file, open and then click on the frequency file I'd saved then open, at this point all that I'd saved previously was back on the screen and then carry on the usual way to upload to the radio.
Works on all my different rigs.
Hope this was of use....
73, Richard de 5B4AJG
Sent from my iPhone
On 30 Oct 2015, at 00:03, slynchmob--- via chirp_users chirp_users@intrepid.danplanet.com wrote:
My UV 6 Baofeng will not respond to up load to chirp I have the right drivers loaded and the wire seem to go all the way in same wire is use for uv82 with no problem
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
That's a common message. The resolution might be found at http://www.miklor.com/COM/UV_ErrorMess.php
Hope this helps.
John Http://www.miklor.com
Sent via iP6
On Oct 30, 2015, at 11:58 AM, slynchmob--- via chirp_users chirp_users@intrepid.danplanet.com wrote:
Every things looks good till I try to up load from radio then it shows that radio did not respond
-----Original Message----- From: John LaMartina JohnLa@usa.net To: 'Discussion of CHIRP' chirp_users@intrepid.danplanet.com Sent: Fri, Oct 30, 2015 11:45 am Subject: Re: [chirp_users] UV-6 programming
Before you started the process, did you initially create a CHIRP template by doing a Download from Radio. CHIRP supports over 80 various models and requires a template to identify the type radio it will be programming.
Refer to (1.1) http://www.miklor.com/COM/UV_CHIRP.php
I hope this assists.
John
From: chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Richard Langmead Sent: Friday, October 30, 2015 4:04 AM To: slynchmob@aol.com; Discussion of CHIRP Subject: Re: [chirp_users] UV-6 programming
Hi, Just a thought as my UV-5RC wouldn't up load from my laptop unless after I'd finished entering the frequencies etc. into Chirp I had to save the page and then X out that file on the screen (plain Chirp screen left on display) then click file, open and then click on the frequency file I'd saved then open, at this point all that I'd saved previously was back on the screen and then carry on the usual way to upload to the radio. Works on all my different rigs. Hope this was of use....
73, Richard de 5B4AJG
Sent from my iPhone
On 30 Oct 2015, at 00:03, slynchmob--- via chirp_users chirp_users@intrepid.danplanet.com wrote: My UV 6 Baofeng will not respond to up load to chirp I have the right drivers loaded and the wire seem to go all the way in same wire is use for uv82 with no problem _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
participants (4)
-
Jim Unroe -
John LaMartina -
Richard Langmead -
slynchmob＠aol.com