Have new radio and this specific model does not appear on the list when setting up to clone the radio. I have tried every model on the list and I get same result "Radio did not respond. I can see the USB Serial Port (Com3) installed and the USB Serial Converter pops up when the connector cable is installed . (I did install largest drivers.)
So as the "newer" radio not listed am I just out of luck or what? I bought cable from BTECH and downloaded CHIRP from WWW.Baofengtech.com/download as instructed.
Chris Luppens
Perhaps nobody has asked for that model to be included.
On 16 June 2020 at 19:22 Chris Luppens jcluppens@ussailing.net wrote:
Have new radio and this specific model does not appear on the list when setting up to clone the radio. I have tried every model on the list and I get same result “Radio did not respond. I can see the USB Serial Port (Com3) installed and the USB Serial Converter pops up when the connector cable is installed . (I did install largest drivers.) So as the “newer” radio not listed am I just out of luck or what? I bought cable from BTECH and downloaded CHIRP from WWW.Baofengtech.com/download as instructed. Chris Luppens _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Nigel Gunn, W8IFF at nigel@ngunn.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Nigel A. Gunn, ///shoulders.outwards.resolutions tel +1 937 825 5032 Amateur Radio G8IFF W8IFF and GMRS WRBV701, e-mail nigel@ngunn.net www http://www.ngunn.net
On Tue, Jun 16, 2020 at 7:24 PM Chris Luppens jcluppens@ussailing.net wrote:
Have new radio and this specific model does not appear on the list when setting up to clone the radio. I have tried every model on the list and I get same result “Radio did not respond. I can see the USB Serial Port (Com3) installed and the USB Serial Converter pops up when the connector cable is installed . (I did install largest drivers.)
So as the “newer” radio not listed am I just out of luck or what? I bought cable from BTECH and downloaded CHIRP from WWW.Baofengtech.com/download as instructed.
Chris Luppens
The selection you should use is most likely Vendor: Radioddity and Model: UV-5RX3. If you try this and it fails, attach a debug.log file.
Jim KC9HI
Not sure I am responding properly but found cross reference and yes UV-5RX3 worked!! My first time at this so am learning "tricks" as I go,,, Thanks much!
Chris KG5BBF
--Original Message----- From: chirp_users-bounces@intrepid.danplanet.com chirp_users-bounces@intrepid.danplanet.com On Behalf Of Jim Unroe Sent: Tuesday, June 16, 2020 7:07 PM To: Discussion of CHIRP chirp_users@intrepid.danplanet.com Subject: Re: [chirp_users] BAOFENG UV-S9T
On Tue, Jun 16, 2020 at 7:24 PM Chris Luppens jcluppens@ussailing.net wrote:
Have new radio and this specific model does not appear on the list when setting up to clone the radio. I have tried every model on the list and I get same result “Radio did not respond. I can see the USB Serial Port (Com3) installed and the USB Serial Converter pops up when the connector cable is installed . (I did install largest drivers.)
So as the “newer” radio not listed am I just out of luck or what? I bought cable from BTECH and downloaded CHIRP from WWW.Baofengtech.com/download as instructed.
Chris Luppens
The selection you should use is most likely Vendor: Radioddity and Model: UV-5RX3. If you try this and it fails, attach a debug.log file.
Jim KC9HI _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John Luppens at jcluppens@ussailing.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
On Tue, Jun 16, 2020 at 9:34 PM Chris Luppens jcluppens@ussailing.net wrote:
Not sure I am responding properly but found cross reference and yes UV-5RX3 worked!! My first time at this so am learning "tricks" as I go,,, Thanks much!
Chris KG5BBF
Chris,
This is what the Supported Radio Models list shows.
Baofeng/Pofung * UV-S9 (use Radioddity UV-5RX3)
I will update it to show the UV-S9T.
Jim KC9HI
I found it. Did not make sense at first but caught on. The model is correct. The “T” is for just the battery pack, listing is correct. (UV-S9).
Thanks much!!
Chris KG5BBF
On Jun 16, 2020, at 8:55 PM, Jim Unroe rock.unroe@gmail.com wrote:
On Tue, Jun 16, 2020 at 9:34 PM Chris Luppens jcluppens@ussailing.net wrote:
Not sure I am responding properly but found cross reference and yes UV-5RX3 worked!! My first time at this so am learning "tricks" as I go,,, Thanks much!
Chris KG5BBF
Chris,
This is what the Supported Radio Models list shows.
Baofeng/Pofung
- UV-S9 (use Radioddity UV-5RX3)
I will update it to show the UV-S9T.
Jim KC9HI _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John Luppens at jcluppens@ussailing.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Thanks for the feedback, it has been added to the list of supported radios :-)
73 Bernhard AE6YN
On 16-Jun-20 18:32, Chris Luppens wrote:
Not sure I am responding properly but found cross reference and yes UV-5RX3 worked!! My first time at this so am learning "tricks" as I go,,, Thanks much!
Chris KG5BBF
--Original Message----- From: chirp_users-bounces@intrepid.danplanet.com chirp_users-bounces@intrepid.danplanet.com On Behalf Of Jim Unroe Sent: Tuesday, June 16, 2020 7:07 PM To: Discussion of CHIRP chirp_users@intrepid.danplanet.com Subject: Re: [chirp_users] BAOFENG UV-S9T
On Tue, Jun 16, 2020 at 7:24 PM Chris Luppens jcluppens@ussailing.net wrote:
Have new radio and this specific model does not appear on the list when setting up to clone the radio. I have tried every model on the list and I get same result “Radio did not respond. I can see the USB Serial Port (Com3) installed and the USB Serial Converter pops up when the connector cable is installed . (I did install largest drivers.)
So as the “newer” radio not listed am I just out of luck or what? I bought cable from BTECH and downloaded CHIRP from WWW.Baofengtech.com/download as instructed.
Chris Luppens
The selection you should use is most likely Vendor: Radioddity and Model: UV-5RX3. If you try this and it fails, attach a debug.log file.
Jim KC9HI _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John Luppens at jcluppens@ussailing.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Bernhard Hailer at ae6yn@arrl.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
participants (4)
-
Bernhard Hailer -
Chris Luppens -
Jim Unroe -
Nigel A. Gunn G8IFF/W8IFF