Ok the procedure I followed tonight was:

Firstly … used windows to check the connection, downloaded from the radio and saved file. Uploaded to radio - worked 100%

Then ran Chirp on the Mac Downloaded from the radio … all good - all settings as per the radio. Uploaded back to the radio … all looked good - the progress bar moved to 100%, and the radio showed CL IN … then waited a while and the progress bar disappeared and gave a message:

An error has occurred. Failure to communicate with radio: did not get clone result from radio.

Switched the radio off, removed the programming cable, switched on and the radio screen showed "Clear" and everything is wiped from the radio and it is reset to factory default.

Went back to Windows and reloaded file to the radio.

Hope this helps.

Regards

Peter ZS1OH

On 13 Aug 2015, at 5:22 PM, John LaMartina JohnLa@usa.net wrote:

To assist further, what is the Exact error message you are receiving?

John

Also, for clarification, one Download From the radio, and Uploads To the radio.

John

• http://www.miklor.com

-----Original Message----- From: chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Peter O'Hanlon Sent: Thursday, August 13, 2015 1:44 AM To: chirp_users@intrepid.danplanet.com Subject: [chirp_users] Icom IC-V82

My IC-V82 doesn't work with Chirp.

I am using Chirp for Mac. Works 100% with my Baofeng UV5-R. Chirp uploads from the radio and downloads to the radio until right at the end it says that there was an error and wipes the radio.

I have to use a Windows machine to program it.

Any ideas/solutions?

Cheers

Pete ZS1OH _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com

---

No virus found in this message. Checked by AVG - www.avg.com Version: 2015.0.6086 / Virus Database: 4401/10429 - Release Date: 08/13/15

---

chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com

On Thu, Aug 13, 2015 at 12:25 PM, Peter O'Hanlon pohanlon@iafrica.com wrote:

Ok the procedure I followed tonight was:

Firstly … used windows to check the connection, downloaded from the radio and saved file. Uploaded to radio - worked 100%

Then ran Chirp on the Mac Downloaded from the radio … all good - all settings as per the radio. Uploaded back to the radio … all looked good - the progress bar moved to 100%, and the radio showed CL IN … then waited a while and the progress bar disappeared and gave a message:

An error has occurred. Failure to communicate with radio: did not get clone result from radio.

Switched the radio off, removed the programming cable, switched on and the radio screen showed "Clear" and everything is wiped from the radio and it is reset to factory default.

Went back to Windows and reloaded file to the radio.

Hope this helps.

Regards

Peter ZS1OH

Chirp uses the same source code on every operating system, so we can rule out Chirp code as the source of this issue. What differs between operating systems is the USB serial driver. My guess the driver you have installed in OS X is not 100% compatible with the chip in your cable and the software and your cable stopped communicating partway through the transfer. I don't know much about your cable, but you might look into installing a different driver.

If it only happened once, it's also possible this was a transient error that you'll never see again (maybe a dirty connection to the radio).

Tom KD7LXL

Prolific

On 14 Aug 2015, at 1:56 AM, Ryan Tourge ryan.tourge@gmail.com wrote:

It is funny. My Mac is opposite of windows. It doesn't care what prolific chip it sees but ftdi has to be just right lol

On Aug 13, 2015 19:25, "Tom Hayward" tom@tomh.us wrote: On Thu, Aug 13, 2015 at 12:25 PM, Peter O'Hanlon pohanlon@iafrica.com wrote:

...

Ok the procedure I followed tonight was:

Firstly … used windows to check the connection, downloaded from the radio and saved file. Uploaded to radio - worked 100%

Then ran Chirp on the Mac Downloaded from the radio … all good - all settings as per the radio. Uploaded back to the radio … all looked good - the progress bar moved to 100%, and the radio showed CL IN … then waited a while and the progress bar disappeared and gave a message:

An error has occurred. Failure to communicate with radio: did not get clone result from radio.

Switched the radio off, removed the programming cable, switched on and the radio screen showed "Clear" and everything is wiped from the radio and it is reset to factory default.

Went back to Windows and reloaded file to the radio.

Hope this helps.

Regards

Peter ZS1OH

Chirp uses the same source code on every operating system, so we can rule out Chirp code as the source of this issue. What differs between operating systems is the USB serial driver. My guess the driver you have installed in OS X is not 100% compatible with the chip in your cable and the software and your cable stopped communicating partway through the transfer. I don't know much about your cable, but you might look into installing a different driver.

If it only happened once, it's also possible this was a transient error that you'll never see again (maybe a dirty connection to the radio).

Tom KD7LXL _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com

Thanks.

I'll try a different driver. It's not a once-off; it happens every time.

Cheers

Peter

-----Original Message----- From: chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Tom Hayward Sent: 14 August 2015 01:09 To: Discussion of CHIRP chirp_users@intrepid.danplanet.com Subject: Re: [chirp_users] Icom IC-V82

On Thu, Aug 13, 2015 at 12:25 PM, Peter O'Hanlon pohanlon@iafrica.com wrote:

Ok the procedure I followed tonight was:

Firstly … used windows to check the connection, downloaded from the radio and saved file. Uploaded to radio - worked 100%

Then ran Chirp on the Mac Downloaded from the radio … all good - all settings as per the radio. Uploaded back to the radio … all looked good - the progress bar moved to 100%, and the radio showed CL IN … then waited a while and the progress bar disappeared and gave a message:

An error has occurred. Failure to communicate with radio: did not get clone result from radio.

Switched the radio off, removed the programming cable, switched on and the radio screen showed "Clear" and everything is wiped from the radio and it is reset to factory default.

Went back to Windows and reloaded file to the radio.

Hope this helps.

Regards

Peter ZS1OH

Chirp uses the same source code on every operating system, so we can rule out Chirp code as the source of this issue. What differs between operating systems is the USB serial driver. My guess the driver you have installed in OS X is not 100% compatible with the chip in your cable and the software and your cable stopped communicating partway through the transfer. I don't know much about your cable, but you might look into installing a different driver.

If it only happened once, it's also possible this was a transient error that you'll never see again (maybe a dirty connection to the radio).

Tom KD7LXL _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com