[chirp_users] Program cable with CHIRP software
I purchased the BTECH- Baofeng Tech.com programming cable, #PC03 FTDI Cable Dual Pin, UPC # 7 0174807090409; along with the new BF-F8HP and UV-5R radios. When I attach the programming cable to the radio and connect the USB end of the programming cable to USB port on the computer; I receive a warning message, telling me this radio's driver is experimental, and asking if I want to proceed? I do have the CHIRP software installed on this computer. I have attached an image of the warning message. I am not sure if I should proceed or not. Can you offer some guidance with this? Thank you,
On Sun, Oct 20, 2019 at 9:50 PM Augliera Jim via chirp_users chirp_users@intrepid.danplanet.com wrote:
I purchased the BTECH- Baofeng Tech.com programming cable, #PC03 FTDI Cable Dual Pin, UPC # 7 0174807090409; along with the new BF-F8HP and UV-5R radios.
When I attach the programming cable to the radio and connect the USB end of the programming cable to USB port on the computer; I receive a warning message, telling me this radio's driver is experimental, and asking if I want to proceed? I do have the CHIRP software installed on this computer.
I have attached an image of the warning message. I am not sure if I should proceed or not.
Can you offer some guidance with this?
Thank you,
Yes. Continue and have fun programming your radio.
Jim KC9HI
Thanks for the reply Jim. I just wanted to be sure it was ok to continue. I watched a few You Tube videos, but didn't see this warning message. I'm new to this programming stuff. Rather be safe than sorry. Thank you again.
Sent from Yahoo Mail on Android
On Sun, Oct 20, 2019 at 8:11 PM, Jim Unroerock.unroe@gmail.com wrote: On Sun, Oct 20, 2019 at 9:50 PM Augliera Jim via chirp_users chirp_users@intrepid.danplanet.com wrote:
I purchased the BTECH- Baofeng Tech.com programming cable, #PC03 FTDI Cable Dual Pin, UPC # 7 0174807090409; along with the new BF-F8HP and UV-5R radios.
When I attach the programming cable to the radio and connect the USB end of the programming cable to USB port on the computer; I receive a warning message, telling me this radio's driver is experimental, and asking if I want to proceed? I do have the CHIRP software installed on this computer.
I have attached an image of the warning message. I am not sure if I should proceed or not.
Can you offer some guidance with this?
Thank you,
Yes. Continue and have fun programming your radio.
Jim KC9HI _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Jim at dr350jja@yahoo.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
I have gotten the same message with other BTECH radios and have proceeded without problems.
Colton Meyer WD6CWM, WRDD814
On 10/20/2019 6:48 PM, Augliera Jim via chirp_users wrote:
I purchased the BTECH- Baofeng Tech.com programming cable, #PC03 FTDI Cable Dual Pin, UPC # 7 0174807090409; along with the new BF-F8HP and UV-5R radios.
When I attach the programming cable to the radio and connect the USB end of the programming cable to USB port on the computer; I receive a warning message, telling me this radio's driver is experimental, and asking if I want to proceed? I do have the CHIRP software installed on this computer.
I have attached an image of the warning message. I am not sure if I should proceed or not.
Can you offer some guidance with this?
Thank you,
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Colton Meyer at cwmeyer@hughes.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
As Colton mentioned, that’s the standard CHIRP disclaimer.
John
Www.Miklor.com
On Oct 21, 2019, at 12:05 PM, Colton Meyer cwmeyer@hughes.net wrote:
I have gotten the same message with other BTECH radios and have proceeded without problems.
Colton Meyer WD6CWM, WRDD814
On 10/20/2019 6:48 PM, Augliera Jim via chirp_users wrote:
I purchased the BTECH- Baofeng Tech.com programming cable, #PC03 FTDI Cable Dual Pin, UPC # 7 0174807090409; along with the new BF-F8HP and UV-5R radios.
When I attach the programming cable to the radio and connect the USB end of the programming cable to USB port on the computer; I receive a warning message, telling me this radio's driver is experimental, and asking if I want to proceed? I do have the CHIRP software installed on this computer.
I have attached an image of the warning message. I am not sure if I should proceed or not.
Can you offer some guidance with this?
Thank you,
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Colton Meyer at cwmeyer@hughes.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
There is a box to click that makes the message never reappear.
It's just a disclaimer basically saying, "You paid nothing for the software and we're just coding as we go with no guarantees."
Which reminds me. Donate to Dan here: https://chirp.danplanet.com/projects/chirp/wiki/Download If everyone just sent him $5
Dennis M. Wage (W9BOQ)
245 Corum Hill Road Castalian Springs, TN 37031 (615) 310-4242 Cell (615) 562-5128 Home http://hammondb3organ.net http://overdubs.net
On Mon, Oct 21, 2019 at 11:14 AM John LaMartina JohnLa@usa.net wrote:
As Colton mentioned, that’s the standard CHIRP disclaimer.
John
Www.Miklor.com
On Oct 21, 2019, at 12:05 PM, Colton Meyer cwmeyer@hughes.net wrote:
I have gotten the same message with other BTECH radios and have proceeded without problems.
Colton Meyer WD6CWM, WRDD814 On 10/20/2019 6:48 PM, Augliera Jim via chirp_users wrote:
I purchased the BTECH- Baofeng Tech.com programming cable, #PC03 FTDI Cable Dual Pin, UPC # 7 0174807090409; along with the new BF-F8HP and UV-5R radios.
When I attach the programming cable to the radio and connect the USB end of the programming cable to USB port on the computer; I receive a warning message, telling me this radio's driver is experimental, and asking if I want to proceed? I do have the CHIRP software installed on this computer.
I have attached an image of the warning message. I am not sure if I should proceed or not.
Can you offer some guidance with this?
Thank you,
chirp_users mailing listchirp_users@intrepid.danplanet.comhttp://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Colton Meyer at cwmeyer@hughes.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to John LaMartina at johnla@usa.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Dennis Wage at dwage@dwage.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Yes I can fuck it mother as free tomorrow night
On Mon, 21 Oct 2019, 05:19 Augliera Jim via chirp_users, < chirp_users@intrepid.danplanet.com> wrote:
I purchased the BTECH- Baofeng Tech.com programming cable, #PC03 FTDI Cable Dual Pin, UPC # 7 0174807090409; along with the new BF-F8HP and UV-5R radios.
When I attach the programming cable to the radio and connect the USB end of the programming cable to USB port on the computer; I receive a warning message, telling me this radio's driver is experimental, and asking if I want to proceed? I do have the CHIRP software installed on this computer.
I have attached an image of the warning message. I am not sure if I should proceed or not.
Can you offer some guidance with this?
Thank you,
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Orbit at reza.bahrami1980@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Well, that seems helpful...
Tom Henderson
On 10/22/19 10:03 AM, Reza Rahgozar wrote:
Yes I can fuck it mother as free tomorrow night
On Mon, 21 Oct 2019, 05:19 Augliera Jim via chirp_users, <chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com> wrote:
I purchased the BTECH- Baofeng Tech.com programming cable, #PC03 FTDI Cable Dual Pin, UPC # 7 0174807090409; along with the new BF-F8HP and UV-5R radios. When I attach the programming cable to the radio and connect the USB end of the programming cable to USB port on the computer; I receive a warning message, telling me this radio's driver is experimental, and asking if I want to proceed? I do have the CHIRP software installed on this computer. I have attached an image of the warning message. I am not sure if I should proceed or not. Can you offer some guidance with this? Thank you, _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com <mailto:chirp_users@intrepid.danplanet.com> http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Orbit at reza.bahrami1980@gmail.com <mailto:reza.bahrami1980@gmail.com> To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com <mailto:chirp_users-unsubscribe@intrepid.danplanet.com>
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Tom KM4UQB at tom@henderson4.us To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Gads
On Oct 22, 2019, at 10:06 AM, Reza Rahgozar reza.bahrami1980@gmail.com wrote:
Yes I can fuck it mother as free tomorrow night
On Mon, 21 Oct 2019, 05:19 Augliera Jim via chirp_users, <chirp_users@intrepid.danplanet.commailto:chirp_users@intrepid.danplanet.com> wrote: I purchased the BTECH- Baofeng Tech.com programming cable, #PC03 FTDI Cable Dual Pin, UPC # 7 0174807090409; along with the new BF-F8HP and UV-5R radios.
When I attach the programming cable to the radio and connect the USB end of the programming cable to USB port on the computer; I receive a warning message, telling me this radio's driver is experimental, and asking if I want to proceed? I do have the CHIRP software installed on this computer.
I have attached an image of the warning message. I am not sure if I should proceed or not.
Can you offer some guidance with this?
Thank you,
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.commailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Orbit at reza.bahrami1980@gmail.commailto:reza.bahrami1980@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.commailto:chirp_users-unsubscribe@intrepid.danplanet.com _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Charlie at charliko@live.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
participants (8)
-
Augliera Jim -
Charlie Koonce -
Colton Meyer -
Dennis Wage -
Jim Unroe -
John LaMartina -
Reza Rahgozar -
Tom Henderson