[chirp_users] How to empty or null tone channel in Chirp?
When I use Chirp to set radio channels, there are many columns I cannot let empty, unless I cannot save it or uploat to radio. Most repeaters here have no subtone and I cannot let tone column empty, or null or zero. In chirp, there is a preseted tone list from 67.0 to 254.1. When I power on the transceiver in frequency mode and ajust to repeater channel, I can hear people talking normally. When I power on in channel mode and choose the respective channel with the same frequency, I cannot hear people talking. Pearhaps, tone values are wrong and in most cases they are unnecessary. How to I solve this? I have a Baofeng UV-82 WITH 8 Watts (HP). Firmware 3 KEY: N822413 6 KEY: 140902N
TKS
PU4YOU
You should be able to leave the "TONE" column empty, which means the values in rToneFreq, cToneFreq will be ignored. And like you said those columns cannot be empty. If you do leave them empty, Chirp by default will add 88.5 as extraneous data that will be ignored.
Hope this helps.
DW
Dennis M. Wage (W9BOQ)
245 Corum Hill Road Castalian Springs, TN 37031 (615) 310-4242 Cell (615) 562-5128 Home http://hammondb3organ.net http://overdubs.net
On Wed, Jul 4, 2018 at 8:48 AM, survivor@cryptolab.net wrote:
When I use Chirp to set radio channels, there are many columns I cannot let empty, unless I cannot save it or uploat to radio. Most repeaters here have no subtone and I cannot let tone column empty, or null or zero. In chirp, there is a preseted tone list from 67.0 to 254.1. When I power on the transceiver in frequency mode and ajust to repeater channel, I can hear people talking normally. When I power on in channel mode and choose the respective channel with the same frequency, I cannot hear people talking. Pearhaps, tone values are wrong and in most cases they are unnecessary. How to I solve this? I have a Baofeng UV-82 WITH 8 Watts (HP). Firmware 3 KEY: N822413 6 KEY: 140902N
TKS
PU4YOU
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Dennis Wage at dwage@dwage.com To unsubscribe, send an email to chirp_users-unsubscribe@ intrepid.danplanet.com
typical uk repeater
first column
freq - 145.625 name - gb3nw tone mode - tone tone - 67 next few are empty duplex is - (minus) offset - 0.6 mode -fm power - high
----- Original Message ----- From: survivor@cryptolab.netmailto:survivor@cryptolab.net To: chirp_users@intrepid.danplanet.commailto:chirp_users@intrepid.danplanet.com Sent: Wednesday, July 04, 2018 2:48 PM Subject: [chirp_users] How to empty or null tone channel in Chirp?
When I use Chirp to set radio channels, there are many columns I cannot let empty, unless I cannot save it or uploat to radio. Most repeaters here have no subtone and I cannot let tone column empty, or null or zero. In chirp, there is a preseted tone list from 67.0 to 254.1. When I power on the transceiver in frequency mode and ajust to repeater channel, I can hear people talking normally. When I power on in channel mode and choose the respective channel with the same frequency, I cannot hear people talking. Pearhaps, tone values are wrong and in most cases they are unnecessary. How to I solve this? I have a Baofeng UV-82 WITH 8 Watts (HP). Firmware 3 KEY: N822413 6 KEY: 140902N
TKS
PU4YOU
________________________________
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to m1cfk at ne.b@hotmail.co.uk To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Dennis M. Wage (W9BOQ)
245 Corum Hill Road Castalian Springs, TN 37031 (615) 310-4242 Cell (615) 562-5128 Home http://hammondb3organ.net http://overdubs.net
On Wed, Jul 4, 2018 at 9:06 AM, neil b ne.b@hotmail.co.uk wrote:
typical uk repeater
first column
freq - 145.625 name - gb3nw tone mode - tone tone - 67 next few are empty duplex is - (minus) offset - 0.6 mode -fm power - high
----- Original Message ----- *From:* survivor@cryptolab.net *To:* chirp_users@intrepid.danplanet.com *Sent:* Wednesday, July 04, 2018 2:48 PM *Subject:* [chirp_users] How to empty or null tone channel in Chirp?
When I use Chirp to set radio channels, there are many columns I cannot let empty, unless I cannot save it or uploat to radio. Most repeaters here have no subtone and I cannot let tone column empty, or null or zero. In chirp, there is a preseted tone list from 67.0 to 254.1. When I power on the transceiver in frequency mode and ajust to repeater channel, I can hear people talking normally. When I power on in channel mode and choose the respective channel with the same frequency, I cannot hear people talking. Pearhaps, tone values are wrong and in most cases they are unnecessary. How to I solve this? I have a Baofeng UV-82 WITH 8 Watts (HP). Firmware 3 KEY: N822413 6 KEY: 140902N
TKS
PU4YOU
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to m1cfk at ne.b@hotmail.co.uk To unsubscribe, send an email to chirp_users-unsubscribe@ intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Dennis Wage at dwage@dwage.com To unsubscribe, send an email to chirp_users-unsubscribe@ intrepid.danplanet.com
On Wed, Jul 4, 2018 at 9:48 AM, survivor@cryptolab.net wrote:
When I use Chirp to set radio channels, there are many columns I cannot let empty, unless I cannot save it or uploat to radio. Most repeaters here have no subtone and I cannot let tone column empty, or null or zero. In chirp, there is a preseted tone list from 67.0 to 254.1. When I power on the transceiver in frequency mode and ajust to repeater channel, I can hear people talking normally. When I power on in channel mode and choose the respective channel with the same frequency, I cannot hear people talking. Pearhaps, tone values are wrong and in most cases they are unnecessary. How to I solve this? I have a Baofeng UV-82 WITH 8 Watts (HP). Firmware 3 KEY: N822413 6 KEY: 140902N
TKS
PU4YOU
Setting Tone Mode to "(None)" is the same has having menu 10 (R-DCS), 11 (R-CTCS), 12 (T-DCS) and 13 (T-CTCS) set to OFF. If the Tone, ToneSql, DTCS Code, DTCS Rx Code DTCS Pol and Cross Mode columns don't show up as blank, then click "View" in the menu bar and enable "Hide unused fields" (which is the default on new CHIRP installations). Even when this setting is not enabled, the values in these columns are ignored.
The values in the columns mentioned above a only recognized when they are enabled by the selected Tone Mode. And then only the columns required by that mode are paid attention to. For example...
Tone Mode: Columns (None): Tone: Tone TSQL: ToneSql DTCS: DTCS Code, DTCS Pol
For more details review either of the "columns" guides linked here: http://www.miklor.com/COM/UV_CHIRP.php#guides
Jim KC9HI
I suggest not hiding the columns so you begin to understand how it all works.
Just my opinion. DW
Dennis M. Wage (W9BOQ)
245 Corum Hill Road Castalian Springs, TN 37031 (615) 310-4242 Cell (615) 562-5128 Home http://hammondb3organ.net http://overdubs.net
On Wed, Jul 4, 2018 at 9:34 AM, Jim Unroe rock.unroe@gmail.com wrote:
On Wed, Jul 4, 2018 at 9:48 AM, survivor@cryptolab.net wrote:
When I use Chirp to set radio channels, there are many columns I cannot
let
empty, unless I cannot save it or uploat to radio. Most repeaters here
have
no subtone and I cannot let tone column empty, or null or zero. In chirp, there is a preseted tone list from 67.0 to 254.1. When I power on the transceiver in frequency mode and ajust to repeater channel, I can hear people talking normally. When I power on in channel mode and choose the respective channel with the same frequency, I cannot hear people talking. Pearhaps, tone values are wrong and in most cases they are unnecessary.
How
to I solve this? I have a Baofeng UV-82 WITH 8 Watts (HP). Firmware 3 KEY: N822413 6 KEY: 140902N
TKS
PU4YOU
Setting Tone Mode to "(None)" is the same has having menu 10 (R-DCS), 11 (R-CTCS), 12 (T-DCS) and 13 (T-CTCS) set to OFF. If the Tone, ToneSql, DTCS Code, DTCS Rx Code DTCS Pol and Cross Mode columns don't show up as blank, then click "View" in the menu bar and enable "Hide unused fields" (which is the default on new CHIRP installations). Even when this setting is not enabled, the values in these columns are ignored.
The values in the columns mentioned above a only recognized when they are enabled by the selected Tone Mode. And then only the columns required by that mode are paid attention to. For example...
Tone Mode: Columns (None): Tone: Tone TSQL: ToneSql DTCS: DTCS Code, DTCS Pol
For more details review either of the "columns" guides linked here: http://www.miklor.com/COM/UV_CHIRP.php#guides
Jim KC9HI _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Dennis Wage at dwage@dwage.com To unsubscribe, send an email to chirp_users-unsubscribe@ intrepid.danplanet.com
participants (4)
-
Dennis Wage -
Jim Unroe -
neil b -
survivor＠cryptolab.net