Re: [chirp_users] UV5R programming problems
I bought a cheap one from ebay... windows keeps throwing it's toys out of the pram with drivers, but I have worked out what I need to do with that now. My cable has worked with ubuntu, Gentoo and debian happily with no issues...
Btu
sent from my Galaxy S7 Edge - Powered by Percy the purple pig.
On 29 Oct 2016 23:29, "Richard" richard.cs@gmail.com wrote:
Hi Neil,
Thanks for the offer. You're some distance from me but I may take you up if I get really stuck. Could I ask where you bought yours from? When I look I only see cheap cables, even the higher-priced ones are the same cheap cables.
At the moment I think the symptoms probably point elsewhere - given that if I open GtkTerm the radio doesn't go into TX like it does with Chirp, and that I can show characters being looped-back.
Richard
On 29 October 2016 at 23:01, Neil Stone neil.stone@gmail.com wrote:
Hi Richard,
Do you want to try another radio and/or cable? I work overlooking Segensworth roundabout and am more than happy to help if I can.
73
Neil M6LPI
sent from my Galaxy S7 Edge - Powered by Percy the purple pig.
On 29 Oct 2016 22:54, "Richard" richard.cs@gmail.com wrote:
Geographically?
Southampton, UK.
On 29 October 2016 at 14:27, Nigel A. Gunn G8IFF/W8IFF nigel@ngunn.net wrote:
Where are you?
On 29 October 2016 at 07:20 Richard richard.cs@gmail.com wrote:
I know this is a common problem but I have tried all the "usual" things with no success. I am on my second programming cable after the first
one
just didn't get recognised as a USB device, and first attempt I was
able to
download the contents of my radio. Since then however it's not worked
again.
The cable works OK and the drivers are loaded, as confirmed by opening
a
serial terminal, linking the TX and RX pins and observing loopback. The radio goes into TX when powered on with the cable attached and some
vicious
connector trimming doesn't help - I am sure it is going all the way in. Following the order in the Chirp pop-up instructions (cable is already connected to PC and correct serial port selected, radio off, connect
cable,
radio on with volume right up, check no activity, click OK) doesn't
help.
The radio goes into TX as soon as it's booted and after a few seconds
I get
"Radio did not respond".
The radio does *not* go into TX if I have that port open in a serial terminal when I turn the radio on, and presumably if Chirp opened the
port
when the instructional message is displayed (before the radio is
turned on)
but still waited for the user to click OK before trying to communicate
all
would work?
I think that the one time it did work it might have been TX-ing and I
just
got lucky that it didn't interfere with communications - I do remember
some
interference on my monitor which I now know happens when the radio transmits.
Anyone got any good ideas? Given that the radio doesn't go into
transmit
mode when the serial port is open I can't see how it can be bad cable / poor connections.
This is on Linux Mate 1.12.1, with the current daily Chirp build. My
user
is in the dialout group and has serial port access.
Thanks Richard _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Nigel Gunn, W8IFF at nigel@ngunn.net To unsubscribe, send an email to chirp_users-unsubscribe@intrep
id.danplanet.com _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Richard at richard.cs@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrep id.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Neil Stone at neil.stone@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrep id.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Richard at richard.cs@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrep id.danplanet.com
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Neil Stone at neil.stone@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@ intrepid.danplanet.com
participants (1)
-
Neil Stone