[chirp_users] funky firmware
Greetings all,
I am a new Ham with a 40 year background in all things electronic. I just picked up new 3 BF-F8+ radios and ended up having to send one back (couldn't program via cable). The replacement came in with different firmware -GRRR!- and an odd/invalid/strange entry in the ABR menu. See attached pic -I hope it is permitted. I can change value to off through 10 using keypad. From that point the odd character goes away 'till the next time I program with Chip to any value above 10. Above 10 the odd character comes back. Chirp allows 0 to 24 as usual and programs without protest for any value 0 - 24 but cant get actual time to go past 10. Any time less than 10 is handled correctly as expected. I reset radio, changed language back to English and then tried to set backlight beyond 10 seconds with no success. Used CHIRP daily-20150702 and an earlier build with same results. Also, the radio type selected was the UV-5R.
If the radio had a 'normal' display this would be less an issue but with the inverse display it pushes the usability close to the edge in a negative way!
Has anyone seen this behavior? Have I missed a step? Should I consider this a defect and try AGAIN for an exchange?
73
Peter KC3FBB
I believe the radio only supports values up to 10.
Jerry R
On Tue, Aug 4, 2015 at 2:53 PM, Peter p.whalley.usa@gmail.com wrote:
Greetings all,
I am a new Ham with a 40 year background in all things electronic. I just picked up new 3 BF-F8+ radios and ended up having to send one back (couldn't program via cable). The replacement came in with different firmware -GRRR!- and an odd/invalid/strange entry in the ABR menu. See attached pic -I hope it is permitted. I can change value to off through 10 using keypad. From that point the odd character goes away 'till the next time I program with Chip to any value above 10. Above 10 the odd character comes back. Chirp allows 0 to 24 as usual and programs without protest for any value 0 - 24 but cant get actual time to go past 10. Any time less than 10 is handled correctly as expected. I reset radio, changed language back to English and then tried to set backlight beyond 10 seconds with no success. Used CHIRP daily-20150702 and an earlier build with same results. Also, the radio type selected was the UV-5R.
If the radio had a 'normal' display this would be less an issue but with the inverse display it pushes the usability close to the edge in a negative way!
Has anyone seen this behavior? Have I missed a step? Should I consider this a defect and try AGAIN for an exchange?
73
Peter KC3FBB
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
My radio, firmware 297, can be set up to 24 via Chirp. ~Bob
On Tue, Aug 4, 2015 at 18:12 Jerry jriechert@gmail.com wrote:
I believe the radio only supports values up to 10.
Jerry R
On Tue, Aug 4, 2015 at 2:53 PM, Peter p.whalley.usa@gmail.com wrote:
Greetings all,
I am a new Ham with a 40 year background in all things electronic. I just picked up new 3 BF-F8+ radios and ended up having to send one back (couldn't program via cable). The replacement came in with different firmware -GRRR!- and an odd/invalid/strange entry in the ABR menu. See attached pic -I hope it is permitted. I can change value to off through 10 using keypad. From that point the odd character goes away 'till the next time I program with Chip to any value above 10. Above 10 the odd character comes back. Chirp allows 0 to 24 as usual and programs without protest for any value 0 - 24 but cant get actual time to go past 10. Any time less than 10 is handled correctly as expected. I reset radio, changed language back to English and then tried to set backlight beyond 10 seconds with no success. Used CHIRP daily-20150702 and an earlier build with same results. Also, the radio type selected was the UV-5R.
If the radio had a 'normal' display this would be less an issue but with the inverse display it pushes the usability close to the edge in a negative way!
Has anyone seen this behavior? Have I missed a step? Should I consider this a defect and try AGAIN for an exchange?
73
Peter KC3FBB
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
On 8/4/2015 6:14 PM, Bob Burkett wrote:
My radio, firmware 297, can be set up to 24 via Chirp. ~Bob
On Tue, Aug 4, 2015 at 18:12 Jerry jriechert@gmail.com wrote:
I believe the radio only supports values up to 10.
Jerry R
On Tue, Aug 4, 2015 at 2:53 PM, Peter p.whalley.usa@gmail.com wrote:
Greetings all,
I am a new Ham with a 40 year background in all things electronic. I just picked up new 3 BF-F8+ radios and ended up having to send one back (couldn't program via cable). The replacement came in with different firmware -GRRR!- and an odd/invalid/strange entry in the ABR menu. See attached pic -I hope it is permitted. I can change value to off through 10 using keypad. From that point the odd character goes away 'till the next time I program with Chip to any value above 10. Above 10 the odd character comes back. Chirp allows 0 to 24 as usual and programs without protest for any value 0 - 24 but cant get actual time to go past 10. Any time less than 10 is handled correctly as expected. I reset radio, changed language back to English and then tried to set backlight beyond 10 seconds with no success. Used CHIRP daily-20150702 and an earlier build with same results. Also, the radio type selected was the UV-5R.
If the radio had a 'normal' display this would be less an issue but with the inverse display it pushes the usability close to the edge in a negative way!
Has anyone seen this behavior? Have I missed a step? Should I consider this a defect and try AGAIN for an exchange?
73
Peter KC3FBB
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Hi Bob,
No, I have 2 other radios -same model bought at same time that support extended timeout and do NOT have funky characters in that display entry. I forgot to include firmware numbers - sorry for that.
chirp no extended backlight Fw msg1: HN5RV01 Fw msg2: 1FS297
chirp extended backlight Fw msg1: N5R2407 Fw msg2: BFB297
Peter
On Tue, Aug 4, 2015 at 5:53 PM, Peter p.whalley.usa@gmail.com wrote:
Greetings all,
I am a new Ham with a 40 year background in all things electronic. I just picked up new 3 BF-F8+ radios and ended up having to send one back (couldn't program via cable). The replacement came in with different firmware -GRRR!- and an odd/invalid/strange entry in the ABR menu. See attached pic -I hope it is permitted. I can change value to off through 10 using keypad. From that point the odd character goes away 'till the next time I program with Chip to any value above 10. Above 10 the odd character comes back. Chirp allows 0 to 24 as usual and programs without protest for any value 0 - 24 but cant get actual time to go past 10. Any time less than 10 is handled correctly as expected. I reset radio, changed language back to English and then tried to set backlight beyond 10 seconds with no success. Used CHIRP daily-20150702 and an earlier build with same results. Also, the radio type selected was the UV-5R.
If the radio had a 'normal' display this would be less an issue but with the inverse display it pushes the usability close to the edge in a negative way!
Has anyone seen this behavior? Have I missed a step? Should I consider this a defect and try AGAIN for an exchange?
73
Peter KC3FBB
It is not a defect if it works properly with a setting of 1 through 10 or OFF.
The menu system in these radios only supports values from 1 though 10 and OFF. The radio itself will accept and understand values up to 24 so CHIRP was programmed to let you use this extra, but unsupported, capability. In most, if not all, of my radios, a setting of 24 using CHIRP yields a setting of OFF when looking at menu 6 (ABR).
Either ignore the odd value, or only use ABR setting values of 1 - 10 or OFF.
Jim KC9HI
participants (4)
-
Bob Burkett -
Jerry -
Jim Unroe -
Peter