-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1
Hi, I am a linux user, and am running my FT8900 five floors away in a boiler room cabinet. SuSE 13.1 is running on a 1.2 GHz embedded PC and doesn't run graphics very well. I also have aprx and a liveATC.net feed running on the PC.
I'd like to be able to program it without trying to do so kneeling on the concrete floor of the cramped boiler room with a laptop!
I was wondering if there is any way to run chirp from the command line?
73 de Nigel ve3id
- -- Nigel Johnson MSc., MIEEE VE3ID/G4AJQ/VA3MCU
Amateur Radio, the origin of the open-source concept!
http://nigel.homelinux.net http://va3mcu.ham-radio-op.net
You can reach me by voice on Skype: TILBURY2591
If time travel ever will be possible, it already is. Ask me again yesterday
This e-mail is not and cannot, by its nature, be confidential. En route from me to you, it will pass across the public Internet, easily readable by any number of system administrators along the way. Nigel Johnson nw.johnson@ieee.org
Please consider the environment when deciding if you really need to print this message
What I used to run was a Dell Netbook with Windows 7 and its remote desktop client. I then ran CoRD remote desktop clients on my MacBook before I installed Chirp and drivers for Mac. So that lends to the possibility to run your laptop remote from a PC in more comfortable surrounding using a remote desktop client as long as both ends could connect to each other via hardwire and or wifi. I have my doubts about a command line mode for Chirp, but you really don't need it.
________________________________ From: "Nigel Johnson, MIEEE" nw.johnson@ieee.org To: chirp_users@intrepid.danplanet.com Sent: Tuesday, February 4, 2014 5:08 PM Subject: [chirp_users] Command line possible?
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1
Hi, I am a linux user, and am running my FT8900 five floors away in a boiler room cabinet. SuSE 13.1 is running on a 1.2 GHz embedded PC and doesn't run graphics very well. I also have aprx and a liveATC.net feed running on the PC.
I'd like to be able to program it without trying to do so kneeling on the concrete floor of the cramped boiler room with a laptop!
I was wondering if there is any way to run chirp from the command line?
73 de Nigel ve3id
- -- Nigel Johnson MSc., MIEEE VE3ID/G4AJQ/VA3MCU
Amateur Radio, the origin of the open-source concept!
http://nigel.homelinux.net http://va3mcu.ham-radio-op.net
You can reach me by voice on Skype: TILBURY2591
If time travel ever will be possible, it already is. Ask me again yesterday
This e-mail is not and cannot, by its nature, be confidential. En route from me to you, it will pass across the public Internet, easily readable by any number of system administrators along the way. Nigel Johnson nw.johnson@ieee.org
Please consider the environment when deciding if you really need to print this message
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
The radio still needs to be put into clone mode. I think that requires turning the radio on while holding buttons.
_____
From: chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Milton Hywatt Sent: Tuesday, February 04, 2014 5:33 PM To: Discussion of CHIRP Subject: Re: [chirp_users] Command line possible?
What I used to run was a Dell Netbook with Windows 7 and its remote desktop client. I then ran CoRD remote desktop clients on my MacBook before I installed Chirp and drivers for Mac. So that lends to the possibility to run your laptop remote from a PC in more comfortable surrounding using a remote desktop client as long as both ends could connect to each other via hardwire and or wifi. I have my doubts about a command line mode for Chirp, but you really don't need it.
_____
From: "Nigel Johnson, MIEEE" nw.johnson@ieee.org To: chirp_users@intrepid.danplanet.com Sent: Tuesday, February 4, 2014 5:08 PM Subject: [chirp_users] Command line possible?
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1
Hi, I am a linux user, and am running my FT8900 five floors away in a boiler room cabinet. SuSE 13.1 is running on a 1.2 GHz embedded PC and doesn't run graphics very well. I also have aprx and a liveATC.net feed running on the PC.
I'd like to be able to program it without trying to do so kneeling on the concrete floor of the cramped boiler room with a laptop!
I was wondering if there is any way to run chirp from the command line?
73 de Nigel ve3id
- -- Nigel Johnson MSc., MIEEE VE3ID/G4AJQ/VA3MCU
Amateur Radio, the origin of the open-source concept!
http://nigel.homelinux.net http://nigel.homelinux.net/ http://va3mcu.ham-radio-op.net http://va3mcu.ham-radio-op.net/
You can reach me by voice on Skype: TILBURY2591
If time travel ever will be possible, it already is. Ask me again yesterday
This e-mail is not and cannot, by its nature, be confidential. En route from me to you, it will pass across the public Internet, easily readable by any number of system administrators along the way. Nigel Johnson nw.johnson@ieee.org
Please consider the environment when deciding if you really need to print this message
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
+1. Unfortunate side effect of yaesu's clone design. (Maybe they would call this a feature not a bug ;)
If it werent for this you could run vnc, freenx/nx, or just a remote x session. (This is not chirp specific, there are tons of articles on the internet on how to do this.)
________________________________ From: Fred Hillhouse Jr fmhillhouse@comcast.net To: 'Milton Hywatt' mhywattt@yahoo.com; 'Discussion of CHIRP' chirp_users@intrepid.danplanet.com Sent: Tuesday, February 4, 2014 4:45 PM Subject: Re: [chirp_users] Command line possible?
The radio still needs to be put into clone mode. I think that requires turning the radio on while holding buttons.
________________________________
From:chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Milton Hywatt Sent: Tuesday, February 04, 2014 5:33 PM To: Discussion of CHIRP Subject: Re: [chirp_users] Command line possible? What I used to run was a Dell Netbook with Windows 7 and its remote desktop client. I then ran CoRD remote desktop clients on my MacBook before I installed Chirp and drivers for Mac. So that lends to the possibility to run your laptop remote from a PC in more comfortable surrounding using a remote desktop client as long as both ends could connect to each other via hardwire and or wifi. I have my doubts about a command line mode for Chirp, but you really don't need it.
________________________________
From:"Nigel Johnson, MIEEE" nw.johnson@ieee.org To: chirp_users@intrepid.danplanet.com Sent: Tuesday, February 4, 2014 5:08 PM Subject: [chirp_users] Command line possible?
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1
Hi, I am a linux user, and am running my FT8900 five floors away in a boiler room cabinet. SuSE 13.1 is running on a 1.2 GHz embedded PC and doesn't run graphics very well. I also have aprx and a liveATC.net feed running on the PC.
I'd like to be able to program it without trying to do so kneeling on the concrete floor of the cramped boiler room with a laptop!
I was wondering if there is any way to run chirp from the command line?
73 de Nigel ve3id
- -- Nigel Johnson MSc., MIEEE VE3ID/G4AJQ/VA3MCU
Amateur Radio, the origin of the open-source concept!
http://nigel.homelinux.net http://va3mcu.ham-radio-op.net
You can reach me by voice on Skype: TILBURY2591
If time travel ever will be possible, it already is. Ask me again yesterday
This e-mail is not and cannot, by its nature, be confidential. En route from me to you, it will pass across the public Internet, easily readable by any number of system administrators along the way. Nigel Johnson nw.johnson@ieee.org
Please consider the environment when deciding if you really need to print this message
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1
That's no problem, the control head is in my apt! :-)
73 de ve3id
On 02/04/2014 05:45 PM, Fred Hillhouse Jr wrote:
The radio still needs to be put into clone mode. I think that requires turning the radio on while holding buttons.
From: chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Milton Hywatt Sent: Tuesday, February 04, 2014 5:33 PM To: Discussion of CHIRP Subject: Re: [chirp_users] Command line possible?
What I used to run was a Dell Netbook with Windows 7 and its remote desktop client. I then ran CoRD remote desktop clients on my MacBook before I installed Chirp and drivers for Mac. So that lends to the possibility to run your laptop remote from a PC in more comfortable surrounding using a remote desktop client as long as both ends could connect to each other via hardwire and or wifi. I have my doubts about a command line mode for Chirp, but you really don't need it.
From: "Nigel Johnson, MIEEE" nw.johnson@ieee.org To: chirp_users@intrepid.danplanet.com Sent: Tuesday, February 4, 2014 5:08 PM Subject: [chirp_users] Command line possible?
Hi, I am a linux user, and am running my FT8900 five floors away in a boiler room cabinet. SuSE 13.1 is running on a 1.2 GHz embedded PC and doesn't run graphics very well. I also have aprx and a liveATC.net feed running on the PC.
I'd like to be able to program it without trying to do so kneeling on the concrete floor of the cramped boiler room with a laptop!
I was wondering if there is any way to run chirp from the command line?
73 de Nigel ve3id
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
- -- Nigel Johnson MSc., MIEEE VE3ID/G4AJQ/VA3MCU
Amateur Radio, the origin of the open-source concept!
http://nigel.homelinux.net http://va3mcu.ham-radio-op.net
You can reach me by voice on Skype: TILBURY2591
If time travel ever will be possible, it already is. Ask me again yesterday
This e-mail is not and cannot, by its nature, be confidential. En route from me to you, it will pass across the public Internet, easily readable by any number of system administrators along the way. Nigel Johnson nw.johnson@ieee.org
Please consider the environment when deciding if you really need to print this message
Too bad it has to use a data port in the back. My Chinese dual band Anytone AT5888UV programs via the RJ45 mic jack on the remote head. Not sure the serial data communications between the head and the body will work with a really long CAT5 cable. It's been debugged to be asynchronous duplex serial data at 19.2k baud. How many feet of cable are you using Nigel?
________________________________ From: "Nigel Johnson, MIEEE" nw.johnson@ieee.org To: Discussion of CHIRP chirp_users@intrepid.danplanet.com Sent: Tuesday, February 4, 2014 6:01 PM Subject: Re: [chirp_users] Command line possible?
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1
That's no problem, the control head is in my apt! :-)
73 de ve3id
On 02/04/2014 05:45 PM, Fred Hillhouse Jr wrote:
The radio still needs to be put into clone mode. I think that requires turning the radio on while holding buttons.
_____
From: chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Milton Hywatt Sent: Tuesday, February 04, 2014 5:33 PM To: Discussion of CHIRP Subject: Re: [chirp_users] Command line possible?
What I used to run was a Dell Netbook with Windows 7 and its remote desktop client. I then ran CoRD remote desktop clients on my MacBook before I installed Chirp and drivers for Mac. So that lends to the possibility to run your laptop remote from a PC in more comfortable surrounding using a remote desktop client as long as both ends could connect to each other via hardwire and or wifi. I have my doubts about a command line mode for Chirp, but you really don't need it.
_____
From: "Nigel Johnson, MIEEE" nw.johnson@ieee.org To: chirp_users@intrepid.danplanet.com Sent: Tuesday, February 4, 2014 5:08 PM Subject: [chirp_users] Command line possible?
Hi, I am a linux user, and am running my FT8900 five floors away in a boiler room cabinet. SuSE 13.1 is running on a 1.2 GHz embedded PC and doesn't run graphics very well. I also have aprx and a liveATC.net feed running on the PC.
I'd like to be able to program it without trying to do so kneeling on the concrete floor of the cramped boiler room with a laptop!
I was wondering if there is any way to run chirp from the command line?
73 de Nigel ve3id
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
- -- Nigel Johnson MSc., MIEEE VE3ID/G4AJQ/VA3MCU
Amateur Radio, the origin of the open-source concept!
http://nigel.homelinux.net http://va3mcu.ham-radio-op.net
You can reach me by voice on Skype: TILBURY2591
If time travel ever will be possible, it already is. Ask me again yesterday
This e-mail is not and cannot, by its nature, be confidential. En route from me to you, it will pass across the public Internet, easily readable by any number of system administrators along the way. Nigel Johnson nw.johnson@ieee.org
Please consider the environment when deciding if you really need to print this message
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1
I'm not getting the jist of your message, Milton.
The rig is 45m away from the control head and works fine as far as operating the rig goes. I use it all the time. It is better to run a signal cable up to the roof that RG8!
I want to program it from an embedded PC in an adjacent NEMA12 cabinet, about 30cm way up in the boiler room.
The PC is controllable from the apartment five floors below using SSH, but I don't want to start x or vnc since they suck down too many cycles and kill my feed to liveATC.net.
It would be nice if it programmed via the mic jack, I could walk over to the cupboard in my apt. and hook up my laptop!
does that help to explain my situation better?
73 de Nigel ve3id
On 02/04/2014 06:20 PM, Milton Hywatt wrote:
Too bad it has to use a data port in the back. My Chinese dual band Anytone AT5888UV programs via the RJ45 mic jack on the remote head. Not sure the serial data communications between the head and the body will work with a really long CAT5 cable. It's been debugged to be asynchronous duplex serial data at 19.2k baud. How many feet of cable are you using Nigel?
From: "Nigel Johnson, MIEEE" nw.johnson@ieee.org To: Discussion of CHIRP chirp_users@intrepid.danplanet.com Sent: Tuesday, February 4, 2014 6:01 PM Subject: Re: [chirp_users] Command line possible?
That's no problem, the control head is in my apt! :-)
73 de ve3id
On 02/04/2014 05:45 PM, Fred Hillhouse Jr wrote:
The radio still needs to be put into clone mode. I think that requires turning the radio on while holding buttons.
From: chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Milton Hywatt Sent: Tuesday, February 04, 2014 5:33 PM To: Discussion of CHIRP Subject: Re: [chirp_users] Command line possible?
What I used to run was a Dell Netbook with Windows 7 and its remote desktop client. I then ran CoRD remote desktop clients on my MacBook before I installed Chirp and drivers for Mac. So that lends to the possibility to run your laptop remote from a PC in more comfortable surrounding using a remote desktop client as long as both ends could connect to each other via hardwire and or wifi. I have my doubts about a command line mode for Chirp, but you really don't need it.
From: "Nigel Johnson, MIEEE" nw.johnson@ieee.org To: chirp_users@intrepid.danplanet.com Sent: Tuesday, February 4, 2014 5:08 PM Subject: [chirp_users] Command line possible?
Hi, I am a linux user, and am running my FT8900 five floors away in a boiler room cabinet. SuSE 13.1 is running on a 1.2 GHz embedded PC and doesn't run graphics very well. I also have aprx and a liveATC.net feed running on the PC.
I'd like to be able to program it without trying to do so kneeling on the concrete floor of the cramped boiler room with a laptop!
I was wondering if there is any way to run chirp from the command line?
73 de Nigel ve3id
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
- -- Nigel Johnson MSc., MIEEE VE3ID/G4AJQ/VA3MCU
Amateur Radio, the origin of the open-source concept!
http://nigel.homelinux.net http://va3mcu.ham-radio-op.net
You can reach me by voice on Skype: TILBURY2591
If time travel ever will be possible, it already is. Ask me again yesterday
This e-mail is not and cannot, by its nature, be confidential. En route from me to you, it will pass across the public Internet, easily readable by any number of system administrators along the way. Nigel Johnson nw.johnson@ieee.org
Please consider the environment when deciding if you really need to print this message
So you leave these options: 1. run a serial cable along with the control cable, as Milton pointed out 2. maybe run some kind of serial over tcp/ip, like ser2net (personally havent used it)
Chirp is GUI based, and would not be trivial to decouple it or make it "curses". Actually now that I think of it, it might be interesting to allow clone-mode or file-mode radios to do one-shot operations (like upload/download, export, etc) from command-line, but that is something that doesnt exist today...
________________________________ From: "Nigel Johnson, MIEEE" nw.johnson@ieee.org To: Milton Hywatt mhywattt@yahoo.com; Discussion of CHIRP chirp_users@intrepid.danplanet.com Sent: Tuesday, February 4, 2014 5:57 PM Subject: Re: [chirp_users] Command line possible?
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1
I'm not getting the jist of your message, Milton.
The rig is 45m away from the control head and works fine as far as operating the rig goes. I use it all the time. It is better to run a signal cable up to the roof that RG8!
I want to program it from an embedded PC in an adjacent NEMA12 cabinet, about 30cm way up in the boiler room.
The PC is controllable from the apartment five floors below using SSH, but I don't want to start x or vnc since they suck down too many cycles and kill my feed to liveATC.net.
It would be nice if it programmed via the mic jack, I could walk over to the cupboard in my apt. and hook up my laptop!
does that help to explain my situation better?
73 de Nigel ve3id
On 02/04/2014 06:20 PM, Milton Hywatt wrote:
Too bad it has to use a data port in the back. My Chinese dual band Anytone AT5888UV programs via the RJ45 mic jack on the remote head. Not sure the serial data communications between the head and the body will work with a really long CAT5 cable. It's been debugged to be asynchronous duplex serial data at 19.2k baud. How many feet of cable are you using Nigel?
From: "Nigel Johnson, MIEEE" nw.johnson@ieee.org To: Discussion of CHIRP chirp_users@intrepid.danplanet.com Sent: Tuesday, February 4, 2014 6:01 PM Subject: Re: [chirp_users] Command line possible?
That's no problem, the control head is in my apt! :-)
73 de ve3id
On 02/04/2014 05:45 PM, Fred Hillhouse Jr wrote:
The radio still needs to be put into clone mode. I think that requires turning the radio on while holding buttons.
_____
From: chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Milton Hywatt Sent: Tuesday, February 04, 2014 5:33 PM To: Discussion of CHIRP Subject: Re: [chirp_users] Command line possible?
What I used to run was a Dell Netbook with Windows 7 and its remote desktop client. I then ran CoRD remote desktop clients on my MacBook before I installed Chirp and drivers for Mac. So that lends to the possibility to run your laptop remote from a PC in more comfortable surrounding using a remote desktop client as long as both ends could connect to each other via hardwire and or wifi. I have my doubts about a command line mode for Chirp, but you really don't need it.
_____
From: "Nigel Johnson, MIEEE" nw.johnson@ieee.org To: chirp_users@intrepid.danplanet.com Sent: Tuesday, February 4, 2014 5:08 PM Subject: [chirp_users] Command line possible?
Hi, I am a linux user, and am running my FT8900 five floors away in a boiler room cabinet. SuSE 13.1 is running on a 1.2 GHz embedded PC and doesn't run graphics very well. I also have aprx and a liveATC.net feed running on the PC.
I'd like to be able to program it without trying to do so kneeling on the concrete floor of the cramped boiler room with a laptop!
I was wondering if there is any way to run chirp from the command line?
73 de Nigel ve3id
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
- -- Nigel Johnson MSc., MIEEE VE3ID/G4AJQ/VA3MCU
Amateur Radio, the origin of the open-source concept!
http://nigel.homelinux.net http://va3mcu.ham-radio-op.net
You can reach me by voice on Skype: TILBURY2591
If time travel ever will be possible, it already is. Ask me again yesterday
This e-mail is not and cannot, by its nature, be confidential. En route from me to you, it will pass across the public Internet, easily readable by any number of system administrators along the way. Nigel Johnson nw.johnson@ieee.org
Please consider the environment when deciding if you really need to print this message
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1
Serial cable not possible, plaster and concrete in the way!
But ser2net, that's a good idea. I will try it!
tnx es 73 de NIgel ve3id
On 02/04/2014 07:18 PM, Jens J. wrote:
So you leave these options:
- run a serial cable along with the control cable, as Milton pointed out
- maybe run some kind of serial over tcp/ip, like ser2net (personally havent used it)
Chirp is GUI based, and would not be trivial to decouple it or make it "curses". Actually now that I think of it, it might be interesting to allow clone-mode or file-mode radios to do one-shot operations (like upload/download, export, etc) from command-line, but that is something that doesnt exist today...
From: "Nigel Johnson, MIEEE" nw.johnson@ieee.org To: Milton Hywatt mhywattt@yahoo.com; Discussion of CHIRP chirp_users@intrepid.danplanet.com Sent: Tuesday, February 4, 2014 5:57 PM Subject: Re: [chirp_users] Command line possible?
I'm not getting the jist of your message, Milton.
The rig is 45m away from the control head and works fine as far as operating the rig goes. I use it all the time. It is better to run a signal cable up to the roof that RG8!
I want to program it from an embedded PC in an adjacent NEMA12 cabinet, about 30cm way up in the boiler room.
The PC is controllable from the apartment five floors below using SSH, but I don't want to start x or vnc since they suck down too many cycles and kill my feed to liveATC.net.
It would be nice if it programmed via the mic jack, I could walk over to the cupboard in my apt. and hook up my laptop!
does that help to explain my situation better?
73 de Nigel ve3id
On 02/04/2014 06:20 PM, Milton Hywatt wrote:
Too bad it has to use a data port in the back. My Chinese dual band Anytone AT5888UV programs via the RJ45 mic jack on the remote head. Not sure the serial data communications between the head and the body will work with a really long CAT5 cable. It's been debugged to be asynchronous duplex serial data at 19.2k baud. How many feet of cable are you using Nigel?
From: "Nigel Johnson, MIEEE" nw.johnson@ieee.org To: Discussion of CHIRP chirp_users@intrepid.danplanet.com Sent: Tuesday, February 4, 2014 6:01 PM Subject: Re: [chirp_users] Command line possible?
That's no problem, the control head is in my apt! :-)
73 de ve3id
On 02/04/2014 05:45 PM, Fred Hillhouse Jr wrote:
The radio still needs to be put into clone mode. I think that requires turning the radio on while holding buttons.
_____From: chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Milton Hywatt Sent: Tuesday, February 04, 2014 5:33 PM To: Discussion of CHIRP Subject: Re: [chirp_users] Command line possible?
What I used to run was a Dell Netbook with Windows 7 and its remote desktop client. I then ran CoRD remote desktop clients on my MacBook before I installed Chirp and drivers for Mac. So that lends to the possibility to run your laptop remote from a PC in more comfortable surrounding using a remote desktop client as long as both ends could connect to each other via hardwire and or wifi. I have my doubts about a command line mode for Chirp, but you really don't need it.
_____From: "Nigel Johnson, MIEEE" nw.johnson@ieee.org To: chirp_users@intrepid.danplanet.com Sent: Tuesday, February 4, 2014 5:08 PM Subject: [chirp_users] Command line possible?
Hi, I am a linux user, and am running my FT8900 five floors away in a boiler room cabinet. SuSE 13.1 is running on a 1.2 GHz embedded PC and doesn't run graphics very well. I also have aprx and a liveATC.net feed running on the PC.
I'd like to be able to program it without trying to do so kneeling on the concrete floor of the cramped boiler room with a laptop!
I was wondering if there is any way to run chirp from the command line?
73 de Nigel ve3id
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
- -- Nigel Johnson MSc., MIEEE VE3ID/G4AJQ/VA3MCU
Amateur Radio, the origin of the open-source concept!
http://nigel.homelinux.net http://va3mcu.ham-radio-op.net
You can reach me by voice on Skype: TILBURY2591
If time travel ever will be possible, it already is. Ask me again yesterday
This e-mail is not and cannot, by its nature, be confidential. En route from me to you, it will pass across the public Internet, easily readable by any number of system administrators along the way. Nigel Johnson nw.johnson@ieee.org
Please consider the environment when deciding if you really need to print this message
participants (4)
-
Fred Hillhouse Jr -
Jens J. -
Milton Hywatt -
Nigel Johnson, MIEEE