Here's a reference that might assist with the error messages. 
http://www.miklor.com/COM/UV_ErrorMess.php 

Some of resolutions sound cable related, and others driver related. 

I hope this helps.

John 'Miklor'
Http://www.miklor.com 

http://www.miklor.com/COM/UV_Drivers.php 


On Nov 5, 2015, at 3:10 PM, Rodger Hess <rwhess@dcn.org> wrote:

I rolled back my Prolific driver to version 3.2.0.0 and now all is well.

73
--Rodger
KK6OPW




I am having the same problem as Ray, but also with my TH 9800. The TYT software can't see
the radio either. So I don't think it is the plug on the Baofeng cable in my case.

Thanks for any help...

73
--Rodger
KK6OPW

On 11/5/2015 10:53 AM, Gary Runningbear wrote:
Hi Dave, I don't believe there will be a need to be concerned with the port
number if the prolific 2303 driver is downloaded and installed. when I did
that it immediately recognized the circuitry in the patch cord.
On Nov 5, 2015 1:51 PM, "dmdfacp@gmail.com" <dmdfacp@gmail.com> wrote:


How about your serial port ?  I just jumped in, so forgive me if I'm
redundant.
If you do not know which port is being used, unplug your USB-to-radio
cable at the computer end. Re-plug it and watch for a small notice
specifying the port to which the computer connected it. Verify that CHIRP
is looking at the correct port.
I just went through this, within the past half hour. Good luck. I'm a
newbie, here, too.
Dave

Sent from my iPhone
DSP

On Nov 5, 2015, at 1:08 PM, Ray Nelson via chirp_users <
chirp_users@intrepid.danplanet.com> wrote:

I've downloaded the software & installed. I keep getting error message the
radio is not connected. What am I doing wrong?

Sent from my iPad
_______________________________________________
chirp_users mailing list
chirp_users@intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
To unsubscribe, send an email to
chirp_users-unsubscribe@intrepid.danplanet.com

_______________________________________________
chirp_users mailing list
chirp_users@intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
To unsubscribe, send an email to
chirp_users-unsubscribe@intrepid.danplanet.com


Hi Dave, I don't believe there will be a need to be concerned with the port number if the prolific 2303 driver is downloaded and installed. when I did that it immediately recognized the circuitry in the patch cord.

On Nov 5, 2015 1:51 PM, "dmdfacp@gmail.com" <dmdfacp@gmail.com> wrote:
How about your serial port ?  I just jumped in, so forgive me if I'm redundant.  
If you do not know which port is being used, unplug your USB-to-radio cable at the computer end. Re-plug it and watch for a small notice specifying the port to which the computer connected it. Verify that CHIRP is looking at the correct port.
I just went through this, within the past half hour. Good luck. I'm a newbie, here, too. 
Dave

Sent from my iPhone 
DSP

On Nov 5, 2015, at 1:08 PM, Ray Nelson via chirp_users <chirp_users@intrepid.danplanet.com> wrote:

I've downloaded the software & installed. I keep getting error message the radio is not connected. What am I doing wrong?

Sent from my iPad
_______________________________________________