Hi Tony,
I should have mentioned, that this is a live version of Ubuntu on a USB drive with a persistence file, so it should save settings between uses.
Glenn
----- Original Message -----
From: Tony Fuller
To: Discussion of CHIRP
Sent: Friday, May 22, 2020 1:15 PM
Subject: Re: [chirp_users] No USB Port Error

Adding your user to dialout group only takes effect after you log out and log back in which is not practical for a live environment IIRC.

You can use something like the following for live environments:

sudo -g dialout chirpw

This gives the dialout group permission to chirpw program while running as the current user. But I don't see any advantage to doing that over plain "sudo chirpw" (what Jim recommended) unless you get X11/Wayland/Mir errors.

Tony
From: chirp_users-bounces@intrepid.danplanet.com <chirp_users-bounces@intrepid.danplanet.com> on behalf of Glenn K0LNY <glennervin@cableone.net>
Sent: Friday, May 22, 2020 12:57:34 PM
To: Discussion of CHIRP <chirp_users@intrepid.danplanet.com>
Subject: Re: [chirp_users] No USB Port Error
 
I wondered about that, but I have used this computer and this Chirp program
to program other radios, but do you suppose the dialout thing needs to be
run with a different cable?
This is a live instance of Ubuntu and I already added Ubuntu as the user in
dialout I am sure, because the CSV files for my other radios are there as
well.
That is what has me puzzled.
Glenn
----- Original Message -----
From: "Jim Unroe" <rock.unroe@gmail.com>
To: "Discussion of CHIRP" <chirp_users@intrepid.danplanet.com>
Sent: Friday, May 22, 2020 12:51 PM
Subject: Re: [chirp_users] No USB Port Error


On Fri, May 22, 2020 at 1:06 PM Glenn K0LNY <glennervin@cableone.net> wrote:
>
> Hi,
> I just got a new used radio, a Kenwood TH-F6.
> So I plugged in the radio using a non-Kenwood cable and I went into
> "radio" and download from radio and selected my radio model and USB0 and I
> get the message:
> error no 2 cannot open tty/usb0 error cannot locate tty/USB0.
> or something similar.
> I have used this cable and that Ubuntu with Chirp in the past for my other
> radios, and other than different brands of radios, I have always been able
> to do this.
> I know a guy who has done this to this model using the Baofeng cable using
> a different software in Windows, not the Kenwood software, but one that
> they purchased.
> I don't recall the name, but I think it starts with an R.
> At any rate, I'd sooner buy a Kenwood cable than that other software and
> keep using Chirp.
> Hopefully I didn't get it mixed up with the Radioddity cable.
> I thought I had the right cable with the Radioddity when I sent it off.
> I don't know if they put the name of the associated radio on the cables,
> since I'm Blind.
> But any who, would this be an error for the wrong cable?
> Thanks.
> Glenn

Hi Glenn,

>From what you are describing it sounds like you Linux user doen't have
permission to access the port. Either run CHIRP as root or as your
Linus user to the dialout group.

I also have a Kenwood TH-F6a. CHIRP programs it in "live" mode.

Jim KC9HI
_______________________________________________
chirp_users mailing list
chirp_users@intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
This message was sent to Glenn at glennervin@cableone.net
To unsubscribe, send an email to
chirp_users-unsubscribe@intrepid.danplanet.com

_______________________________________________
chirp_users mailing list
chirp_users@intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
This message was sent to Tony F at goldstar611@hotmail.com
To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com

_______________________________________________
chirp_users mailing list
chirp_users@intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
This message was sent to Glenn at glennervin@cableone.net
To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com