Thanks JohnI have seen that as well. For the one that I get a Chinese Character set, I have been able to change to English. The one program I think that can do it has Zero characters on it (english or chinese) and everything is replaced by a ???.Again, I apologize for taking up the space on the Chirp reflector.The best I can tell is that the actual program is called BF-480 based on what I found on 409Shoppe's site.I know the port and the cable work as I can use the same cable and same port (FTDI) to read my UV-5R with Chirp. I also know they aren't holding open the port as I do close down Chirp before testing. I have even tried after a reboot with the BF-480 software being the first code used.My note to self will be to check the Chirp support hardware list first before ordering new hardware! :)Mike va3mwOn Sat, Dec 28, 2013 at 8:06 PM, John LaMartina ☀ <JohnLa@usa.net> wrote:Mike,Not sure if this applies or not, but with some of the software, when it is unzipped, one of the files is a language file, ie. Chinese.ini, English.ini, etc.Delete the Chinese.ini file and only leave the English.iniThis forces the program to open with the only .ini file it finds.Worth a try...John K3NXUHi BillThat is likely the answer, but no joy their either. I have yet to find a button for language changes or anything else that gets me closer.Thanks all, this was just a shot in the dark.Mike va3mwOn Sat, Dec 28, 2013 at 6:57 PM, william coulson <wcoulson730@gmail.com> wrote:
You have to switch it to English by selecting English on the radio buttons. Then the question marks will disappear eh?I hope I understand your issues, if not good luck!Bill----- Original Message -----From: Mike va3mwSent: Saturday, December 28, 2013 3:52 PMSubject: Re: [chirp_users] Baofeng V6Jack and I are seeing the same thing. We don't have the right software for the right radio.I know 100% in my case that the computer, ports and cable are functional.Boafeng own software has language localization issues. The software loads but all the icons are full of question marks. .???The failure is that the program tries to talk to the radio and the radio does not respond, so it times out.Sorry for the bandwidth on the chirp reflector, but this was the best collection of these type of users I know.Sadly there is no BF-v6 listed on their download site.Mike va3mware you sure widows did. not automaticaly upgrade the driver to the newer not compatible version?
בתאריך 28 בדצמ 2013 21:34, "w4grj" <w4grj@satterfield.org> כתב:
I am using the Baofeng software, error message cannot connect to radio
It is not a cable or port issue.
Jack
W4GRJ
From: chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of John LaMartina
Sent: Saturday, December 28, 2013 2:29 PM
To: 'Discussion of CHIRP'
Subject: Re: [chirp_users] Baofeng V6
Is the programming of the UV-6 software or a driver/cable issue.
What error messages are you getting?
John K3NXU . . . http://www.miklor.com
From: chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of w4grj
Sent: Saturday, December 28, 2013 2:15 PM
To: 'Discussion of CHIRP'
Subject: Re: [chirp_users] Baofeng V6
I have a UV-6, also cannot get it to program with the Baofeng software.
Has anyone successfully programmed the UV-6?
Thanks,
Jack
From: chirp_users-bounces@intrepid.danplanet.com [mailto:chirp_users-bounces@intrepid.danplanet.com] On Behalf Of Michael Walker
Sent: Friday, December 27, 2013 10:14 PM
To: Discussion of CHIRP
Subject: Re: [chirp_users] Baofeng V6
Yes, it isn't a port issue.
Mike
On Fri, Dec 27, 2013 at 10:11 PM, Amnon Zohar <amnon.zohar@gmail.com> wrote:
could you comunicate with any other radio?
בתאריך 28 בדצמ 2013 05:07, "Michael Walker" <va3mw@portcredit.net> כתב:
Hi All
I know that this is a little off topic and this radio isn't supported by Chirp, but has anyone actually been able to program one?
This is a 16 Channel VHF only unit.
I've tried just about all the software from Baofeng that I can find, but I have not found anything that will talk to the radio.
I am 'assuming' it is using a Kenwood cable configuration as well.
Mike va3mw
_______________________________________________
chirp_users mailing list
chirp_users@intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
_______________________________________________
chirp_users mailing list
chirp_users@intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
_______________________________________________
chirp_users mailing list
chirp_users@intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
_______________________________________________
chirp_users mailing list
chirp_users@intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
_______________________________________________
chirp_users mailing list
chirp_users@intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
_______________________________________________
chirp_users mailing list
chirp_users@intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
_______________________________________________
chirp_users mailing list
chirp_users@intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
_______________________________________________
chirp_users mailing list
chirp_users@intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users