Here is the file. Chirp offers to open it in read only mode, when you accept it then says it is unsupported.
On Mon, May 29, 2017 at 12:38 AM, Chuck Hast kp4djt@gmail.com wrote:
Dumped it out of the radio.
On Sun, May 28, 2017 at 10:54 PM, Albert Webster <albertlwebster@gmail.com
wrote:
You can send the file to me. I have a IC 5100. What program did you use to creat the original File?
On Sat, May 27, 2017 at 10:51 PM Chuck Hast kp4djt@gmail.com wrote:
Well, I finally got to try it, after two trips from Kelso, WA to Oklahoma City, OK now I am finally getting it all set up here. Do miss my old haunts though...
Tried to access the ics file but I get the following messages:
ICF files cannot be edited, only displayed or imported into another file. Open in Read-only Mode? [Yes] (answer given to proceed)
FileName.icf: Unsupported model
So, can I send a file to someone to take a look at? These are files for the ID-5100. I was sure hoping that this would be the solution to this.
Any ideas, and if someone wants a sample file I can send you one.
On Mon, May 15, 2017 at 2:29 PM, Chuck Hast kp4djt@gmail.com wrote:
Great, I will do so. I am sorry I have been slow to respond, but I moved from Kelso WA to Oklahoma City and have been up to my neck in moving "fun" With the ID-5100 I just write to the SD card used in the radio so being able to talk direct to the radio is not a big deal.
Had a good time doing radio while driving from Kelso to OKC. There were a lot of dead (no users) repeaters though. Seems that you do not hear many folks on any longer.
On Wed, May 10, 2017 at 7:42 AM, David Dixon < yattonbristol@btinternet.com> wrote:
Chuck
If you look in the chirp program and go to file open then look at all files type Botton right it will show you the ICF is on the list
Hope that helps
From: chirp_users-bounces@intrepid.danplanet.com on behalf of "Nigel A. Gunn G8IFF/W8IFF" nigel@ngunn.net Reply-To: Discussion of CHIRP chirp_users@intrepid.danplanet.com Date: Wednesday, 10 May 2017 at 13:09 To: Discussion of CHIRP chirp_users@intrepid.danplanet.com Subject: Re: [chirp_users] Icom ICF files
No.
What are icf files anyway?
On 10 May 2017 at 07:16 Chuck Hast kp4djt@gmail.com wrote:
Does anyone know if Chirp will write icf files? If it will then my ID-5100 issue may be solved. _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Nigel Gunn, W8IFF at nigel@ngunn.net To unsubscribe, send an email to chirp_users-unsubscribe@intrep id.danplanet.com
_______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/ mailman/listinfo/chirp_users This message was sent to David at yattonbristol@btinternet.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck Hast at kp4djt@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrep id.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Albert Webster at albertlwebster@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrep id.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck Hast at kp4djt@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrep id.danplanet.com