You can raise is as an issue under new model here https://chirp.danplanet.com/projects/chirp/issues/new Tony G7TXU
On Fri, 27 Aug 2021 at 00:26, Ken Hansen ken@n2vip.org wrote:
I suspect as soon as someone loans/donates a radio to a CHIRP programmer to work on support.
Ken
On Aug 26, 2021, at 18:10, Eric Chopin echopin27@gmail.com wrote:
Yaesu FT270 H/H
Greetings, so far I have used CHIRP with 100% success in programming many radios. What I REALLY need is being able to program the YAESU FT270 Hand Held. When is one of you brilliant guys going to update CHIRP with this radio?
Thanks VE7ECJ
On Sun, Aug 22, 2021 at 12:01 PM < chirp_users-request@intrepid.danplanet.com> wrote:
Send chirp_users mailing list submissions to chirp_users@intrepid.danplanet.com
To subscribe or unsubscribe via the World Wide Web, visit http://intrepid.danplanet.com/mailman/listinfo/chirp_users or, via email, send a message with subject or body 'help' to chirp_users-request@intrepid.danplanet.com
You can reach the person managing the list at chirp_users-owner@intrepid.danplanet.com
When replying, please edit your Subject line so it is more specific than "Re: Contents of chirp_users digest..."
Today's Topics:
- Re: UV5X Programming issue (White Ranger)
Message: 1 Date: Sat, 21 Aug 2021 14:33:09 -0500 From: White Ranger cortchubby20007@gmail.com Subject: Re: [chirp_users] UV5X Programming issue To: Discussion of CHIRP chirp_users@intrepid.danplanet.com Message-ID: <CAP+N95FGwe= VRT21Yd+EiDSjhknL0j_xGhMZqD7PEJXniiT93Q@mail.gmail.com> Content-Type: text/plain; charset="utf-8"
Radio should be ON when up or downloading. Remove the driver and cable program, reboot PC reload driver SHOULD correct issue. If using aftermarket cable check to see contacts are CLEAN (*shiny) and fit TIGHTLY into the mike provisioning adapter (Mic jack) DO NOT touch ANY buttons while programming. Worst case, prior to programming RESET the radio to factory resets then load your amended program.
On Thu, Aug 19, 2021 at 2:03 PM Jim Unroe rock.unroe@gmail.com wrote:
Hi Eric,
On Thu, Aug 19, 2021 at 12:47 PM Eric Chopin echopin27@gmail.com
wrote:
UV5XP.... However to get CHIRP to see the radio either in the 'Download from
radio'
or 'Upload to radio' ... with the cable plugged in to my PC or myMAC, the
radio must me switched OFF...then as I select 'Download or upload'as I
select 'OK' i must immediately switch ON my radio then CHIRP seesit
and
proceeds. If I try to 'Download or upload' with the radio alreadyswitched
on I get the message 'The radio did not respond' as CHIRP cannotsee
it
connected. Any suggestions? Thanks VE7ECJThat sounds like a programming cable/driver issue. Also, to program that radio you must choose...
Vendor: Radioddity Model: UV-5G
Jim KC9HI _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to cortchubby20007@gmail.com at cortchubby20007@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com