In my configuration for a BaoFeng F8-HP there are 5 values for the Duplex setting (None, -, +, Split, Off)
I believe + and - are variations of split.
On Fri, Mar 10, 2017 at 9:22 AM John LaMartina ☀ JohnLa@usa.net wrote:
Duplex None = Tx / Rx on the same freq = Simplex Duplex Split = Tx / Rx on split freq = Repeater Duplex Off = Rx only = No Transmit
John Http://www.miklor.com
On Mar 10, 2017, at 10:53 AM, Doyle Pugmire sambopugmire@gmail.com wrote:
I have the Baofeng 82-hp. After reading the conversation below, I set my radio on a local police frequency that is programed with “Duplex” set to None and tested it to make sure I wouldn’t transmit on it. I pressed the transmit button and the red light on top came on and the transmit indicator on the screen showed it was transmitting. From what I have read that means it is transmitting. Wouldn’t the radio transmit if I only selected “split”?
On Mar 9, 2017, at 9:47 PM, Mike Kartchner masterwulfe@gmail.com wrote:
Simple test press the tx an see if your red indicator light come on (if not it is not broadcasting) but I have noticed in some cases (if before you set it to off) it was at + or -, it will not reset to that same + or -, it will go to o in some repeater cases that need that + or - setting an the off set factor.
On Thu, Mar 9, 2017 at 4:47 PM, Richard B. Booth cqw6rkk@gmail.com wrote:
For the Baofeng UV-5R and variants……..when programming a simplex frequency channel…… will setting the Duplex option in CHIRP to “Off” result in suppressing the TX in simplex operations?
The reason for asking is as follows: I have several police and fire freqs programmed into my radios, i.e., simplex. I want to make sure that even if I make a mistake and hit the TX key, I will not TX on these freqs.
I have in the past programmed these memory channels using split mode and setting the TX on a dummy freq well away from the agency RX/TX freq.
Thanks for any help !!
Notice: This message content and attachments are intended for the sole use of the intended recipient(s).
Any use by unauthorized persons is prohibited and may be unlawful. Forwarding of this email without the
permission of the sender, original sender, or author is not authorized. Forwarding without permission negates
all liability, stated or implied, as applicable to the sender, original sender, or author.
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Mike Kartchner at masterwulfe@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Doyle at sambopugmire@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users
This message was sent to John LaMartina at johnla@usa.net
To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Drew Einhorn at drew.einhorn@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com