Send chirp_users mailing list submissions to
        chirp_users@intrepid.danplanet.com

To subscribe or unsubscribe via the World Wide Web, visit
        http://intrepid.danplanet.com/mailman/listinfo/chirp_users
or, via email, send a message with subject or body 'help' to
        chirp_users-request@intrepid.danplanet.com

You can reach the person managing the list at
        chirp_users-owner@intrepid.danplanet.com

When replying, please edit your Subject line so it is more specific
than "Re: Contents of chirp_users digest..."


Today's Topics:

   1. Re: UV5X Programming issue (White Ranger)


----------------------------------------------------------------------

Message: 1
Date: Sat, 21 Aug 2021 14:33:09 -0500
From: White Ranger <cortchubby20007@gmail.com>
Subject: Re: [chirp_users] UV5X Programming issue
To: Discussion of CHIRP <chirp_users@intrepid.danplanet.com>
Message-ID:
        <CAP+N95FGwe=VRT21Yd+EiDSjhknL0j_xGhMZqD7PEJXniiT93Q@mail.gmail.com>
Content-Type: text/plain; charset="utf-8"

Radio should be ON when up or downloading.
Remove the driver and cable program, reboot PC reload driver
SHOULD correct issue. If using aftermarket cable check to see contacts are
CLEAN (*shiny) and fit TIGHTLY into the mike provisioning adapter (Mic
jack) DO NOT touch ANY buttons while programming. Worst case, prior to
programming RESET the radio to factory resets then load your amended
program.

On Thu, Aug 19, 2021 at 2:03 PM Jim Unroe <rock.unroe@gmail.com> wrote:

> Hi Eric,
>
> On Thu, Aug 19, 2021 at 12:47 PM Eric Chopin <echopin27@gmail.com> wrote:
> >
> > UV5XP....
> >     However to get CHIRP to see the radio either in the 'Download from
> radio'
> >     or 'Upload to radio' ... with the cable plugged in to my PC or my
> MAC, the
> >     radio must me switched OFF...then as I select 'Download or upload'
> as I
> >     select 'OK' i must immediately switch ON my radio then CHIRP sees it
> and
> >     proceeds. If I try to 'Download or upload' with the radio already
> switched
> >     on I get the message 'The radio did not respond' as CHIRP cannot see
> it
> >     connected.
> >     Any suggestions?
> >     Thanks
> >     VE7ECJ
>
> That sounds like a programming cable/driver issue. Also, to program
> that radio you must choose...
>
> Vendor: Radioddity
> Model: UV-5G
>
> Jim KC9HI
> _______________________________________________
> chirp_users mailing list
> chirp_users@intrepid.danplanet.com
> http://intrepid.danplanet.com/mailman/listinfo/chirp_users
> This message was sent to cortchubby20007@gmail.com at
> cortchubby20007@gmail.com
> To unsubscribe, send an email to
> chirp_users-unsubscribe@intrepid.danplanet.com
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://intrepid.danplanet.com/pipermail/chirp_users/attachments/20210821/b544e8b4/attachment-0001.html

------------------------------

_______________________________________________
chirp_users mailing list
chirp_users@intrepid.danplanet.com
http://intrepid.danplanet.com/mailman/listinfo/chirp_users
To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com

End of chirp_users Digest, Vol 152, Issue 12
********************************************