4 Apr
2019
4 Apr
'19
5:51 a.m.
Lynn's APRSISCE runs fine under WINE and packet is easy if you've got a real TNC. If not, use DIREWOLF.
On 03 April 2019 at 23:46 Larry Lovell larry.lovell76@gmail.com wrote:
Thanks, I mentioned the other platforms. Right now, I am trying to get Packet and then APRS running on my Raspberry Pi. I will try CHIRP on it as well. On Wed, Apr 3, 2019 at 8:04 PM Chuck Hast < kp4djt@gmail.com mailto:kp4djt@gmail.com > wrote: > > Also do not forget it runs on the major platforms, i.e. It started out on Linux and is of course available forWindows (as you have presented) and Mac. I believe it will also run under BSD. A lot of us like to run it on a Raspberry Pi. On Tue, Apr 2, 2019 at 6:57 PM Amnon Zohar < amnon.zohar@gmail.com mailto:amnon.zohar@gmail.com > wrote: > > > remark for your presentationthe cheap cables with clone prolific chips works fine with the older driver version 3.2.0.0 a good source for technical staff can be found athttp://www.miklor.com (the bible ofradios) you can download that driver there.... בתאריך יום ג׳, 2 באפר׳ 2019 ב-23:44 מאת Larry Lovell < larry.lovell76@gmail.com mailto:larry.lovell76@gmail.com >: > > > > I wish to thank all of you for your findings on the Yaesu radios.I am giving a presentation on CHIRP to our local (Eastern Idaho) HAMs tonight. If you are interested, the PDF of my presentation is located at: http://www.qrvtronics.com/CatHAM_Radio/files/UsingCHIRPorOtherSoftware.pdf On Thu, Mar 28, 2019 at 10:36 PM < chirp.cordless@xoxy.net mailto:chirp.cordless@xoxy.net > wrote: > > > > > Well there's some truth there, but what truth I'm awareof should not scare anyone off from using chirp with Yaesus. Back in early 2014 I was doing some chirp code development on FT-60s, fixing some bugs and with the eventual goal of adding "Settings" control. Someone else has since done that. Part of that process is mapping the memory by twiddling bits in the image, uploading to the radio, and seeing through the radio's button interface what changed. It went pretty smoothly for a while, then I managed to brick *TWO* FT-60s. One of which was repaired by sending it to the factory to replace an eprom. I'm not going to add any further detail here, my investigation was pretty thoroughly documented in a thread on the chirp_devel mail list with subject "How to brick an FT-60" starting 3/22/14. See also Bug #1547: [FT-60] Chirp should check parity on download. But normal use of chirp to program radios doesn't do this. The user interface only lets you make limited, well understood changes to the radio image bitmap. I still do that with mine. -dan > Date: Wed, 27 Mar 2019 22:05:06 -0600 > From: Larry Lovell < larry.lovell76@gmail.com mailto:larry.lovell76@gmail.com > > Subject: [chirp_users] Programming Yaesu Radios using CHIRP > To: Discussion of CHIRP < chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com > > > Has anyone had a problem programming a Yaesu radio with CHIRP? > Someone mentioned that their Yaesu was damaged and had to be sent to the > factory because CHIRP had overwritten some code controlling the processor. > It also had to be re-flashed. > Since I don't fully understand how CHIRP works this doesn't make sense to > me, but knowing manufacturing companies, they may share Channel Memory with > processor memory and not think much about it. > Thanks for your information. _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Larry Lovell at larry.lovell76@gmail.com mailto:larry.lovell76@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com > > > >-- Larry Lovell 73's N7RGW http://QRVTronics.com http://qrvtronics.com Cell: 214-697-1729 _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to amnon at amnon.zohar@gmail.com mailto:amnon.zohar@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com > > >-- Amnon _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Chuck Hast at kp4djt@gmail.com mailto:kp4djt@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com > >-- Chirp + Editcp + MD380Tools on Linux Celestial!!! Chuck -- KP4DJT _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com mailto:chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Larry Lovell at larry.lovell76@gmail.com mailto:larry.lovell76@gmail.com To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com mailto:chirp_users-unsubscribe@intrepid.danplanet.com >-- Larry Lovell 73's N7RGW http://QRVTronics.com http://qrvtronics.com Cell: 214-697-1729 _______________________________________________ chirp_users mailing list chirp_users@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Nigel Gunn, W8IFF at nigel@ngunn.net To unsubscribe, send an email to chirp_users-unsubscribe@intrepid.danplanet.com
Nigel A. Gunn, 1865 El Camino Drive, Xenia, OH 45385-1115, USA. tel +1 937 825 5032 Amateur Radio G8IFF W8IFF and GMRS WRBV701, e-mail nigel@ngunn.net www http://www.ngunn.net