August 2023 - Users - lists.chirpmyradio.com

[chirp_users] FTM-3100R
by Andy Zaayenga 09 Aug '23

09 Aug '23

Hi folks, I've got a new-to-me Yaesu FTM-3100R. Picked up a cable from BlueMax49ers to run with CHIRP. I downloaded the radio using the FTM-3200D R template as per the CHIRP home page. Downloading and uploading works fine. I copied and pasted from my Yaesu FT-60R img 63 of the frequencies I monitor that are covered by the FTM-3100R. Uploading those to the radio works fine and downloading shows them all in memory. However, I notice that when I scan all 63 frequencies the radio only scans the first 14. The display just stops on the 14th location while the numbers under MR keep counting up to 63. Then it cycles back to location 1. I have the radios side by side and the FT-60R scans all the locations while the FTM-3100R only the first 14. The specs say the radio has 199 memory locations which is consistent with the CHIRP img * 199 "basic" memory channels, numbered "1" through "199". But the CHIRP image doesn't show the home channel or any of the L or U locations. * A "Home" channel, providing storage and quick recall of one prime frequency. * 10 sets of band-edge memories, also known as "Programmable Memory Scan" channels, labeled "L0/U0" through "L9/U9". Does anyone out there have an FTM-3100R and can let me know if I'm doing something wrong? I'm wondering if there's some issue with the FTM-3200D R template WRT the FTM-3100R. Thanks from a first-time poster! 73 Andy Zaayenga KD2SME Yaesu FT-60R, Yaesu FTM-3100R

2 5

[chirp_users] Developer mode browser has become R/O?
by Ron 09 Aug '23

09 Aug '23

In the past I was able to change things in the developer mode browser to work around bugs but now it won't let me enter/change anything? This happened after I recovered from a disk corruption and had to re-install CHIRP (possibly a newer build). Everything else works normally as before. Thanks, Ron

1 0

Re: [chirp_users] FTM-3100R
by Andy Zaayenga 07 Aug '23

07 Aug '23

Sorry, Dick. That file is my CHIRP file, and I renamed it with a bak extension because most servers do not allow img files due to security protocol. As Danny points out, you can delete the .bak part to make it an img file that can be read into CHIRP. Tonight I installed the CHIRP Legacy edition and went through the same exercise. No difference from the current version. The operative question is – Does anyone on this list use CHIRP successfully for their Yaesu FTM-3100R? Then I would know if it’s something about my configuration or CHIRP itself. Thanks all. Andy From: Danny Siminiuk <danny(a)siminiuk.com> Sent: Monday, August 7, 2023 5:22 PM To: chirp users <chirp_users(a)intrepid.danplanet.com> Cc: peter.fontneau <peter.fontneau(a)icloud.com>; Andy Zaayenga <andy(a)zaayenga.net> Subject: Re: [chirp_users] FTM-3100R "I’ve attached the img file, renamed to a bak extension" Rename <https://z8.zimbrahostedemail.com/service/home/~/?auth=co&loc=en_US&id=13351…> Yaesu_FTM-3100R.img.bak to <https://z8.zimbrahostedemail.com/service/home/~/?auth=co&loc=en_US&id=13351…> Yaesu_FTM-3100R.img Get it? _____ From: "w4rss" <w4rss(a)radioclub.org <mailto:w4rss@radioclub.org> > To: "peter.fontneau" <peter.fontneau(a)icloud.com <mailto:peter.fontneau@icloud.com> >, "chirp users" <chirp_users(a)intrepid.danplanet.com <mailto:chirp_users@intrepid.danplanet.com> >, "Andy Zaayenga" <andy(a)zaayenga.net <mailto:andy@zaayenga.net> > Sent: Monday, August 7, 2023 4:18:25 PM Subject: Re: [chirp_users] FTM-3100R Andy, that img.bak file will not open on my tablet. I get a message that .bak files are not recognized. Dick On Aug 7, 2023 at 2:12 PM, Andy Zaayenga via chirp_users <chirp_users(a)intrepid.danplanet.com <mailto:chirp_users@intrepid.danplanet.com> > wrote: Thanks Peter. None of the locations are marked Skip. For reference, I’ve attached the img file, renamed to a bak extension so the servers don’t block it. The Skip field only accepts S (Skip) or blank, there is no dropdown for Priority. The manual references that there is only one Priority channel, kept in memory location 0. No memory location 0 shows in the CHIRP file. 73 Andy From: peter.fontneau(a)icloud.com <mailto:peter.fontneau@icloud.com> <peter.fontneau(a)icloud.com <mailto:peter.fontneau@icloud.com> > Sent: Monday, August 7, 2023 12:58 PM To: Andy Zaayenga <andy(a)zaayenga.net <mailto:andy@zaayenga.net> >; chirp_users(a)intrepid.danplanet.com <mailto:chirp_users@intrepid.danplanet.com> Subject: Re: [chirp_users] FTM-3100R Check to see if you have something entered in the Skip column of Chirp. https://chirp.danplanet.com/projects/chirp/wiki/MemoryEditorColumns Skip The scan skip mode for the channel. The values and their meanings are: * S: Skip this channel during scan * P: This channel is a priority On Aug 6, 2023, at 9:40 PM, Andy Zaayenga via chirp_users <chirp_users(a)intrepid.danplanet.com <mailto:chirp_users@intrepid.danplanet.com> > wrote: Hi folks, I've got a new-to-me Yaesu FTM-3100R. Picked up a cable from BlueMax49ers to run with CHIRP. I downloaded the radio using the FTM-3200D R template as per the CHIRP home page. Downloading and uploading works fine. I copied and pasted from my Yaesu FT-60R img 63 of the frequencies I monitor that are covered by the FTM-3100R. Uploading those to the radio works fine and downloading shows them all in memory. However, I notice that when I scan all 63 frequencies the radio only scans the first 14. The display just stops on the 14th location while the numbers under MR keep counting up to 63. Then it cycles back to location 1. I have the radios side by side and the FT-60R scans all the locations while the FTM-3100R only the first 14. The specs say the radio has 199 memory locations which is consistent with the CHIRP img * 199 "basic" memory channels, numbered "1" through "199". But the CHIRP image doesn't show the home channel or any of the L or U locations. * A "Home" channel, providing storage and quick recall of one prime frequency. * 10 sets of band-edge memories, also known as "Programmable Memory Scan" channels, labeled "L0/U0" through "L9/U9". Does anyone out there have an FTM-3100R and can let me know if I'm doing something wrong? I'm wondering if there's some issue with the FTM-3200D R template WRT the FTM-3100R. Thanks from a first-time poster! 73 Andy Zaayenga KD2SME Yaesu FT-60R, Yaesu FTM-3100R <Yaesu_FTM-3100R_2023-08-06.csv>_______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com <mailto:chirp_users@intrepid.danplanet.com> http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Pete at peter.jay12(a)icloud.com <mailto:peter.jay12@icloud.com> To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com <mailto:chirp_users-unsubscribe@intrepid.danplanet.com> To report this email as off-topic, please email chirp_users-owner(a)intrepid.danplanet.com <mailto:chirp_users-owner@intrepid.danplanet.com> Searchable archive: https://www.mail-archive.com/chirp_users@intrepid.danplanet.com _______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Dick Smith at w4rss(a)radioclub.org <mailto:w4rss@radioclub.org> To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com To report this email as off-topic, please email chirp_users-owner(a)intrepid.danplanet.com Searchable archive: https://www.mail-archive.com/chirp_users@intrepid.danplanet.com _______________________________________________ chirp_users mailing list chirp_users(a)intrepid.danplanet.com <mailto:chirp_users@intrepid.danplanet.com> http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Danny at k5cg(a)hamoperator.org <mailto:k5cg@hamoperator.org> To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com <mailto:chirp_users-unsubscribe@intrepid.danplanet.com> To report this email as off-topic, please email chirp_users-owner(a)intrepid.danplanet.com <mailto:chirp_users-owner@intrepid.danplanet.com> Searchable archive: https://www.mail-archive.com/chirp_users@intrepid.danplanet.com

1 0

Re: [chirp_users] FTM-3100R
by Andy Zaayenga 07 Aug '23

07 Aug '23

Thanks Peter. None of the locations are marked Skip. For reference, I've attached the img file, renamed to a bak extension so the servers don't block it. The Skip field only accepts S (Skip) or blank, there is no dropdown for Priority. The manual references that there is only one Priority channel, kept in memory location 0. No memory location 0 shows in the CHIRP file. 73 Andy From: peter.fontneau(a)icloud.com <peter.fontneau(a)icloud.com> Sent: Monday, August 7, 2023 12:58 PM To: Andy Zaayenga <andy(a)zaayenga.net>; chirp_users(a)intrepid.danplanet.com Subject: Re: [chirp_users] FTM-3100R Check to see if you have something entered in the Skip column of Chirp. https://chirp.danplanet.com/projects/chirp/wiki/MemoryEditorColumns Skip The scan skip mode for the channel. The values and their meanings are: * S: Skip this channel during scan * P: This channel is a priority On Aug 6, 2023, at 9:40 PM, Andy Zaayenga via chirp_users <chirp_users(a)intrepid.danplanet.com <mailto:chirp_users@intrepid.danplanet.com> > wrote: Hi folks, I've got a new-to-me Yaesu FTM-3100R. Picked up a cable from BlueMax49ers to run with CHIRP. I downloaded the radio using the FTM-3200D R template as per the CHIRP home page. Downloading and uploading works fine. I copied and pasted from my Yaesu FT-60R img 63 of the frequencies I monitor that are covered by the FTM-3100R. Uploading those to the radio works fine and downloading shows them all in memory. However, I notice that when I scan all 63 frequencies the radio only scans the first 14. The display just stops on the 14th location while the numbers under MR keep counting up to 63. Then it cycles back to location 1. I have the radios side by side and the FT-60R scans all the locations while the FTM-3100R only the first 14. The specs say the radio has 199 memory locations which is consistent with the CHIRP img * 199 "basic" memory channels, numbered "1" through "199". But the CHIRP image doesn't show the home channel or any of the L or U locations. * A "Home" channel, providing storage and quick recall of one prime frequency. * 10 sets of band-edge memories, also known as "Programmable Memory Scan" channels, labeled "L0/U0" through "L9/U9". Does anyone out there have an FTM-3100R and can let me know if I'm doing something wrong? I'm wondering if there's some issue with the FTM-3200D R template WRT the FTM-3100R. Thanks from a first-time poster! 73 Andy Zaayenga KD2SME Yaesu FT-60R, Yaesu FTM-3100R <Yaesu_FTM-3100R_2023-08-06.csv>____________________________________________ ___ chirp_users mailing list chirp_users(a)intrepid.danplanet.com <mailto:chirp_users@intrepid.danplanet.com> http://intrepid.danplanet.com/mailman/listinfo/chirp_users This message was sent to Pete at peter.jay12(a)icloud.com <mailto:peter.jay12@icloud.com> To unsubscribe, send an email to chirp_users-unsubscribe(a)intrepid.danplanet.com <mailto:chirp_users-unsubscribe@intrepid.danplanet.com> To report this email as off-topic, please email chirp_users-owner(a)intrepid.danplanet.com <mailto:chirp_users-owner@intrepid.danplanet.com> Searchable archive: https://www.mail-archive.com/chirp_users@intrepid.danplanet.com

3 2

[chirp_users] Legacy support question--Programming Talkpod A36+
by Jim Pruitt 07 Aug '23

07 Aug '23

I am still using the last legacy version of Chirp. I just acquired a Talkpod A36+ but can't find how to program it manually and hooking it up to Chirp can not talk to the radio but Talkpod is not in the list. I tried Baofeng UV5R but that did not work. Has anyone else programmed the Talkpod A36+ using Chirp? I tried searching for programming instructions to do it manually but all hits were to a youtube video and used Chirp. Thank you. Jim Pruitt

3 3

Re: [chirp_users] TYT TH-8600 driver available for testing
by Mike 06 Aug '23

06 Aug '23

Does anyone know why upload is grayed out when I try to upload selected frequencies from radio reference? Thanks. On August 5, 2023, at 11:43 AM, Andy Knitt <andyknitt(a)gmail.com> wrote: A driver for the TYT TH-8600 is available for beta testing. It can be found attached to Issue 4851 and can be tested via the "Load Module From Issue" option in the Help menu. Support for 2 Tone, 5 Tone, and DTMF signalling is not yet fully implemented, but CTCSS and DTCS should be working. Please report issues found during testing (or positive results) via the Issue or directly to me via email. Thanks, Andy

3 2

[chirp_users] Programming ICOM IC-7100
by Michael Nadler KI7QIB 05 Aug '23

05 Aug '23

I cannot get CHIRP to properly program an ICOM 7100. Can someone provide the explicit steps they use to program their ICOM IC-7100? Computer, running Windows 10, is connected to the 7100's Remote port via USB cable. CHIRP works fine programming a Kenwood D710G in live mode. I'm following the same steps: - Download from the radio - use "help me" to find the com port - set Vendor/model to ICOM/IC-7100 - tab opens with a copy of what's programmed in the radio - Import from file... - select the CSV file with several hundred entries - click Import - random channels are programmed; others show red numbers, which is an error indication Can no longer download from radio -- the program reports "permission error". I have to restart CHIRP in order to download from the radio. After the restart and download, if I use cut/paste to update say 20 entries -- entries are programmed randomly -- same result as with import. I've searched the mail archives -- some people report problems, tentative solutions are proposed (without documenting specific steps), but no one posts any resolution. This radio programs perfectly with RT Systems software. But their software uses clone mode, not live mode. -- Michael Nadler KI7QIB

1 0

[chirp_users] TYT TH-8600 driver available for testing
by Andy Knitt 05 Aug '23

05 Aug '23

A driver for the TYT TH-8600 is available for beta testing. It can be found attached to Issue 4851 <https://chirp.danplanet.com/issues/4851> and can be tested via the "Load Module From Issue <https://chirp.danplanet.com/projects/chirp/wiki/LoadingTestModules>" option in the Help menu. Support for 2 Tone, 5 Tone, and DTMF signalling is not yet fully implemented, but CTCSS and DTCS should be working. Please report issues found during testing (or positive results) via the Issue or directly to me via email. Thanks, Andy

1 0

[chirp_users] New chirp-next build
by donotreply＠chirp.danplanet.com 03 Aug '23

03 Aug '23

Greetings, A new build of CHIRP-next is available. This includes changes made directly to the tree since yesterday and may include additional features, bug fixes, etc. Unless you have a reason not to, we recommend using the latest build of CHIRP-next at all times. You can get it from here: http://trac.chirp.danplanet.com/chirp_next/ A list of changes since the last build are here: 79fefeb7 FT818: Add PMS as possible scan mode. 96004c2e Clean up ga510 exit handling 6ded5e07 ga510.py: add 'reset' v2 --

1 0