On Mar 23, 2014, at 7:13 AM, Jens J. - kd4tjx@yahoo.com wrote:
Did you say that although the radio appears unresponsive, will it still "act" as if it will clone? If so, will it upload or download, or both?
Multiple attempts at both upload and download time out. Download after several seconds, upload immediately.
I have put it into clone mode enough times that I don't need a display to do it, it's almost muscle memory. The radio shows no indication of response, either in the display or to chirp.
Also, Will it visibly go into alignment mode? To enter the Alignment mode: • Press and hold in the MONI and LAMP switches turn- ing the radio on. Once the radio is on, release these two switches. • Press the keypad in the following sequence: [(MHz)] [0( )SET] [1(SQ TYP)] [7(P1)] [V/M(PRI)] • Press the [F/W] key to cause “A0 REF.xxx” to appear on the display for five seconds, this signifies that the trans- ceiver is now in the “Alignment Mode.”
Nope, no indication of anything in response to several repetitions of this sequence. The backlight remains on, display blank.
... I would be curious to examine your "bad" image vs a previous "good" image, vs even one you might have taken much, much earlier in your development process. Can you share them privately with me directly off-list?
I can provide the "bad" image and one dumped a couple of hours earlier. What I can't say for sure is that uploading the one from a little earlier wouldn't brick it also. The mapping process didn't do very much in the way of uploads, it was mostly twiddle settings, download and diff.
Earlier in the day Mar 22, when this happened, I had been going back on a verification pass, and there were some images before Set item 11 CW WRT that I had uploaded, button-tweaked, downloaded and diffed. It will take me a little time to reconstruct that; it's possible I can identify a file downloaded a little earlier than the BrickMaker.img on Feb 7 that I uploaded March 22 without bricking the radio. Let me work on that.
For now, here's the diff between the BrickMaker and the image created immediately previously on Feb 7, which was for Item 7, BELL, setting it to 'Cont'. Hope this works, I had to use a fixed width font and that required using RTF for this mail; I hope it's not mangled.
-0024 x0018: 12 02 00 00 00 01 00 07 ........ +0024 x0018: 12 02 00 00 00 01 00 0b ........ ^
-0048 x0030: 05 01 04 2e 04 2e 03 00 ........ +0048 x0030: 00 01 04 2e 04 2e 03 00 ........ ^
-0536 x0218: ff ff ff ff ff ff ff ff ........ +0536 x0218: 0a 0b 0c 0c 0b 0b ff ff ........ ^^ ^^ ^^ ^^ ^^ ^^
-28616 x6FC8: 4d 00 00 00 00 00 00 00 M....... +28616 x6FC8: 95 00 00 00 00 00 00 00 ........ ^^ ^
Byte 31 is the "Set Item Number" saved in nonvolatile flash, 7 vs 11. Byte 48 ls 3 bits is the 'Cont' value for BELL. The string starting at 536 is the CW WRT value I keyed in, "ABCCBB". 28616 is the checksum. Pretty innocuous looking eh? But I can't say with any confidence that uploading the other image wouldn't brick it as well.
I could supply images I have successfully uploaded, including immediately prior to bricking the second radio with the same image that bricked the first. But the diffs would be mind-numbing, they were 'operational' configs unrelated to this development work.
Let me see what I can come up with.
-dan