I used xxd, cut and meld to compare and analyze the three dumps. Results:
Yaesu FTM-400D
Comparison of memory dumps to SD card, CLN (assumed to be full memory dump), MEM (memory/channel settings) and SYS (system settings).
Johan Adler, 2014-03-10 (March 10, 2014)
0x0000 to 0x007f: Unknown, identical in all dumps 0x0080 to 0x017f: Settings 0x0180 to 0x01ff: Present in both settings (same address) and memories (at 0x0080 to 0x00ff). 0x0200 to 0x027f: Memories (0x0100 to 0x017f) 0x0280 to 0x02ff: Settings (0x0200 to 0x027f)
0x0300 to 0x03ff: Unknown, 0xff in my dump. 0x0400 to 0x047f: Contains data, APRS-related settings?
0x0480 to 0x04ff: Memories (0x0180 to 0x01ff) 0x0500 to 0x057f: Settings (0x0280 to 0x02ff)
0x0580 to 0x05ff: Unknown, 0xca and 0xff in my dump. 0x0600 to 0x067f: Contains data, likely APRS-related. 0x0680 to 0x07ff: Unknown, 0xca in my dump.
0x0800 to 0x69ff: Memories (0x0200 to 0x63ff), I guess the two main banks.
0x7800 to 0x780f: Unknown, 'ALL' padded with ASCII space in my dump. APRS-related?
0x7c00 to 0x7dff: Unknown, looks like data, maybe settings.
0x8000 to 0x????: APRS reports/contacts, full messages received, 0x80 bytes each.
0xe400 to 0x????: APRS contacts, 0x20 bytes each.
On Mon, Mar 10, 2014 at 7:06 AM, Johan Adler johan.adler@gmail.com wrote:
The radio can save different backups to the card, either a full memory dump (76800 bytes, 0c12c00), only the settings (1024 bytes, 0x400), or only the memories (25600 bytes, 0x6400).
Filenames and paths, relative to SD card root:
Full memory dump ("clone"): FTM400D/BACKUP/CLONE/CLNFTM400D.dat Memories (channel data, I presume): FTM400D/BACKUP/MEMORY/MEMFTM400D.dat Settings: FTM400D/BACKUP/SETUP/SYSFTM400D.dat
The size of the full memory dump minus memories and settings is 50176 bytes, 0xc400, but I guess it is not all empty. I have noticed that for example incoming APRS messages are stored in memory, but I guess those would not be saved with settings or memories. Still, having separate dumps of the settings area and the channel data area should make it easier to locate those areas in the complete memory dump.
I will have a look at the three files, compare them and verify the locations in the full memory dump.
A closer look on the Yaesu MH-85A11U shows that it connects with a (probably modified and non standard) mini USB B only. The female connector on the radio has the usual five pins of a mini USB B, and another six pins. Since the DTMF mic that comes with the radio uses six pins I would guess that those six pins are the same as the regular mic. If I was developing hardware I would not create new stuff but rather reuse existing technology, in this case a standard USB webcam interface combined with the six pin microphone interface already in use.
I opened the SCU-20 USB data cable, confirmed the presence of a PL2303. It connects using five leads both to the radio and to the USB, and I did not at this time remove the shrink tubing to check if the radio connector cable has all 10 leads or if it is a cheaper five lead cable. It would probably be quite easy to just remove the PL2303 side and make a connector for an FTDI interface instead, though. I took some photos of the inside of the interface cable before putting it back together.
On Sat, Mar 8, 2014 at 4:54 PM, Johan Adler johan.adler@gmail.com wrote:
Thank you, Tom,
In fact I just made a rough memory map earlier today, just studying the memory dump file from the memory card with a hex editor. When comparing
my
guesses with the mapping used by the FTM-350 module most major stuff
seems
to be in the same places. There are new features and settings, of course, and I will have to sort those out, but I think I can use the FTM-350
module
as a starting point.
Of course, one difference is the two different ways of accessing the
memory,
cable or card.
I have not found any way of making the radio save more than one
incarnation
of the memory dump, alas.
One possible interesting (non Chirp related thing) about it is the
optional
camera microphone, which connects (for the camera) to what looks a lot
like
a mini USB B, and where such a cable also fits. What if it would be
possible
to connect some simple webcam instead of the more expensive Yaesu cam
mic.
:-)
On Sat, Mar 8, 2014 at 4:41 PM, Tom Hayward esarfl@gmail.com wrote:
On Sat, Mar 8, 2014 at 12:54 AM, Johan Adler johan.adler@gmail.com wrote:
I have cloned the development tree and try to find how the FTM-350 module works regarding memory download to see if can start there. I can also start analyzing the memory image saved to µSD, but it will be a bit tedious
to
change one setting, turn the thing off, take the µSD card to the computer, copy the settings file, compare it to the previous version, put the
card
back, turn on the radio, change another setting, and so on. :-)
How many memory images does it allow you to store on the µSD card? You make it sound like just one, unfortunately. If you can store more than one, you could batch a number of changes into respective files before copying to the computer for analysis.
Yaesus are pretty simple (actually, most all ham radios are). If you upload the memory image and include a few details like what frequency and PL are in the first three channels, I could probably tell you at least where the channel data starts and how long each record is.
Tom KD7LXL _______________________________________________ chirp_devel mailing list chirp_devel@intrepid.danplanet.com http://intrepid.danplanet.com/mailman/listinfo/chirp_devel Developer docs: