August 2021 - Developers - lists.chirpmyradio.com

[chirp_devel] Build test results: Successful
by Build System 13 Aug '21

13 Aug '21

Tested changes: Changes for Build #928 [Jim Unroe <rock.unroe(a)gmail.com>] [UV-5G] Allow Programming GMRS TX/RX Frequencies On All Channels This patch allows programming any combination of GMRS frequencies in memory rows 0 and 31-127. Any non-GMRS frequencies will continue to be restricted to RX only (TX disabled). Related to #9235 [Jim Unroe <rock.unroe(a)gmail.com>] [RT87] Add Retevis RT87 This patch adds support for the Retevis RT87 two-way radio. #6769 [Jim Unroe <rock.unroe(a)gmail.com>] [UV-5G] Fix Incorrect Offset for Repeater Channels This patch updats the driver with the correct offset for the repeater channels 23-30. #9255 [Pavel Milanes (CO7WT) <pavelmc(a)gmail.com>] [PATCH][FTL-x011] Add new driver for FTL-1011/2011/7011/8011 radios #7599 Add suppors for the 4/12/24 variants of the Vertex FTL-1011/2011/7011/8011, there is a later models with 99 channels that uses a different mem layout and is not supported by this driver. [Dan Smith <dsmith(a)danplanet.com>] Allow integer settings in mem.extra Needed for #6769 [Tom Hayward <tom(a)tomh.us>] [id880] Fix typo in charset definition. #281 [Tom Hayward <tom(a)tomh.us>] [thf6a] Support full charset (ASCII). Fixes #141 [Tom Hayward <tom(a)tomh.us>] [id880] Support full charset. Fixes #281 [Tom Hayward <tom(a)tomh.us>] [vx5] Support full charset (ASCII). Fixes #292 [Tom Hayward <tom(a)tomh.us>] [id31a] set used bit when creating new memory, clear when deleting. Fixes #269 [Tom Hayward <tom(a)tomh.us>] Support PyGTK < 2.22 in bank edit. Fixes #231 [Tom Hayward <tom(a)tomh.us>] [d710] [v71] [d72] Fix tone list (not all tones are supported). Fixes #212 [Dan Smith <dsmith(a)danplanet.com>] [vx7] Fix setting memory power levels on 220MHz band Fixes #214 [Dan Smith <dsmith(a)danplanet.com>] fips: Pennsylvania FIPS code was wrong. #117 [Marco Filippi <iz3gme.marco(a)gmail.com>] Consider lower bound frequency of each valid_band as valid Fix bug #181 [Tom Hayward <tom(a)tomh.us>] tmd700: allow 8-char names. Fixes #176 [Dan Smith <dsmith(a)danplanet.com>] Fix the "blind deletion" problem, as well as properly direct copy/paste Fixes #172 [David Griffith <dave(a)661.org>] Bug #155 fix: VX-7 1.25m power levels [David Griffith <dave(a)661.org>] New INSTALL and README files Fixes #122 [Tom Hayward <tom(a)tomh.us>] thd72: only use hardware flow on OS X. Fixes #166 [Marco Filippi <iz3gme.marco(a)gmail.com>] [FT817] Tone freq not set correctly Same as #88 for FT857, to avoid code duplication fix code have been moved from ft857 to its ancestor class Fix bug #163 [Tom Hayward <tom(a)tomh.us>] Fix Mac .app so paths with spaces work. Fixes Bug #145 Full log: [...truncated 883 lines...] test_copy_all (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 copy all ... ok test_detect (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 detect ... ok test_edges (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 edges ... skipped 'No mutable memory locations found' test_settings (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 settings ... ok test_banks (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 brute force ... ok test_clone (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 clone ... ok test_copy_all (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 copy all ... ok test_detect (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 detect ... ok test_edges (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 edges ... ok test_settings (tests.TestCase_AlincoDJ596) Testing Alinco DJ596 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_RadioddityUV5G) Testing Radioddity UV-5G banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RadioddityUV5G) Testing Radioddity UV-5G brute force ... ok test_clone (tests.TestCase_RadioddityUV5G) Testing Radioddity UV-5G clone ... ok test_copy_all (tests.TestCase_RadioddityUV5G) Testing Radioddity UV-5G copy all ... ok test_detect (tests.TestCase_RadioddityUV5G) Testing Radioddity UV-5G detect ... ok test_edges (tests.TestCase_RadioddityUV5G) Testing Radioddity UV-5G edges ... ok test_settings (tests.TestCase_RadioddityUV5G) Testing Radioddity UV-5G settings ... ok test_banks (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 banks ... ok test_brute_force (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 brute force ... ok test_clone (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 clone ... ok test_copy_all (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 copy all ... ok test_detect (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 detect ... ok test_edges (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 edges ... ok test_settings (tests.TestCase_YaesuVX2) Testing Yaesu VX-2 settings ... ok test_banks (tests.TestCase_CRTMicronUV) Testing CRT Micron UV banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_CRTMicronUV) Testing CRT Micron UV brute force ... ok test_clone (tests.TestCase_CRTMicronUV) Testing CRT Micron UV clone ... ok test_copy_all (tests.TestCase_CRTMicronUV) Testing CRT Micron UV copy all ... ok test_detect (tests.TestCase_CRTMicronUV) Testing CRT Micron UV detect ... ok test_edges (tests.TestCase_CRTMicronUV) Testing CRT Micron UV edges ... ok test_settings (tests.TestCase_CRTMicronUV) Testing CRT Micron UV settings ... ok test_banks (tests.TestCase_IcomICW32A) Testing Icom IC-W32A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICW32A) Testing Icom IC-W32A brute force ... ok test_clone (tests.TestCase_IcomICW32A) Testing Icom IC-W32A clone ... ok test_copy_all (tests.TestCase_IcomICW32A) Testing Icom IC-W32A copy all ... ok test_detect (tests.TestCase_IcomICW32A) Testing Icom IC-W32A detect ... ok test_edges (tests.TestCase_IcomICW32A) Testing Icom IC-W32A edges ... ok test_settings (tests.TestCase_IcomICW32A) Testing Icom IC-W32A settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT65R) Testing Yaesu FT-65R banks ... ok test_brute_force (tests.TestCase_YaesuFT65R) Testing Yaesu FT-65R brute force ... ok test_clone (tests.TestCase_YaesuFT65R) Testing Yaesu FT-65R clone ... ok test_copy_all (tests.TestCase_YaesuFT65R) Testing Yaesu FT-65R copy all ... ok test_detect (tests.TestCase_YaesuFT65R) Testing Yaesu FT-65R detect ... ok test_edges (tests.TestCase_YaesuFT65R) Testing Yaesu FT-65R edges ... ok test_settings (tests.TestCase_YaesuFT65R) Testing Yaesu FT-65R settings ... ok test_banks (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G banks ... ok test_brute_force (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G brute force ... ok test_clone (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G clone ... ok test_copy_all (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G copy all ... ok test_detect (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G detect ... ok test_edges (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G edges ... ok test_settings (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G settings ... ok test_banks (tests.TestCase_WouxunKGUV8E) Testing Wouxun KG-UV8E banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUV8E) Testing Wouxun KG-UV8E brute force ... ok test_clone (tests.TestCase_WouxunKGUV8E) Testing Wouxun KG-UV8E clone ... ok test_copy_all (tests.TestCase_WouxunKGUV8E) Testing Wouxun KG-UV8E copy all ... ok test_detect (tests.TestCase_WouxunKGUV8E) Testing Wouxun KG-UV8E detect ... ok test_edges (tests.TestCase_WouxunKGUV8E) Testing Wouxun KG-UV8E edges ... ok test_settings (tests.TestCase_WouxunKGUV8E) Testing Wouxun KG-UV8E settings ... ok test_banks (tests.TestCase_AlincoDR235T) Testing Alinco DR235T banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AlincoDR235T) Testing Alinco DR235T brute force ... ok test_clone (tests.TestCase_AlincoDR235T) Testing Alinco DR235T clone ... ok test_copy_all (tests.TestCase_AlincoDR235T) Testing Alinco DR235T copy all ... ok test_detect (tests.TestCase_AlincoDR235T) Testing Alinco DR235T detect ... ok test_edges (tests.TestCase_AlincoDR235T) Testing Alinco DR235T edges ... ok test_settings (tests.TestCase_AlincoDR235T) Testing Alinco DR235T settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 brute force ... ok test_clone (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 clone ... ok test_copy_all (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 copy all ... ok test_detect (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 detect ... ok test_edges (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 edges ... ok test_settings (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 settings ... ok test_banks (tests.TestCase_RadtelT18) Testing Radtel T18 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RadtelT18) Testing Radtel T18 brute force ... ok test_clone (tests.TestCase_RadtelT18) Testing Radtel T18 clone ... ok test_copy_all (tests.TestCase_RadtelT18) Testing Radtel T18 copy all ... ok test_detect (tests.TestCase_RadtelT18) Testing Radtel T18 detect ... ok test_edges (tests.TestCase_RadtelT18) Testing Radtel T18 edges ... ok test_settings (tests.TestCase_RadtelT18) Testing Radtel T18 settings ... ok test_banks (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A brute force ... ok test_clone (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A clone ... ok test_copy_all (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A copy all ... ok test_detect (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A detect ... ok test_edges (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A edges ... ok test_settings (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A settings ... ok test_banks (tests.TestCase_TYTTH7800) Testing TYT TH-7800 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTH7800) Testing TYT TH-7800 brute force ... ok test_clone (tests.TestCase_TYTTH7800) Testing TYT TH-7800 clone ... ok test_copy_all (tests.TestCase_TYTTH7800) Testing TYT TH-7800 copy all ... ok test_detect (tests.TestCase_TYTTH7800) Testing TYT TH-7800 detect ... ok test_edges (tests.TestCase_TYTTH7800) Testing TYT TH-7800 edges ... ok test_settings (tests.TestCase_TYTTH7800) Testing TYT TH-7800 settings ... ok test_banks (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 banks ... ok test_brute_force (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 brute force ... ok test_clone (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 clone ... ok test_copy_all (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 copy all ... ok test_detect (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 detect ... ok test_edges (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 edges ... ok test_settings (tests.TestCase_YaesuVX3) Testing Yaesu VX-3 settings ... ok test_banks (tests.TestCase_IcomICW32E) Testing Icom IC-W32E banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICW32E) Testing Icom IC-W32E brute force ... ok test_clone (tests.TestCase_IcomICW32E) Testing Icom IC-W32E clone ... ok test_copy_all (tests.TestCase_IcomICW32E) Testing Icom IC-W32E copy all ... ok test_detect (tests.TestCase_IcomICW32E) Testing Icom IC-W32E detect ... ok test_edges (tests.TestCase_IcomICW32E) Testing Icom IC-W32E edges ... ok test_settings (tests.TestCase_IcomICW32E) Testing Icom IC-W32E settings ... skipped 'Settings not supported' test_banks (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 brute force ... ok test_clone (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 clone ... ok test_copy_all (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 copy all ... ok test_detect (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 detect ... ok test_edges (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 edges ... ok test_settings (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 settings ... ok test_banks (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus brute force ... ok test_clone (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus clone ... ok test_copy_all (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus copy all ... ok test_detect (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus detect ... ok test_edges (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus edges ... ok test_settings (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus settings ... ok test_banks (tests.TestCase_AnyTone5888UV) Testing AnyTone 5888UV banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AnyTone5888UV) Testing AnyTone 5888UV brute force ... ok test_clone (tests.TestCase_AnyTone5888UV) Testing AnyTone 5888UV clone ... ok test_copy_all (tests.TestCase_AnyTone5888UV) Testing AnyTone 5888UV copy all ... ok test_detect (tests.TestCase_AnyTone5888UV) Testing AnyTone 5888UV detect ... ok test_edges (tests.TestCase_AnyTone5888UV) Testing AnyTone 5888UV edges ... ok test_settings (tests.TestCase_AnyTone5888UV) Testing AnyTone 5888UV settings ... ok test_banks (tests.TestCase_RetevisRB17A) Testing Retevis RB17A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRB17A) Testing Retevis RB17A brute force ... ok test_clone (tests.TestCase_RetevisRB17A) Testing Retevis RB17A clone ... ok test_copy_all (tests.TestCase_RetevisRB17A) Testing Retevis RB17A copy all ... ok test_detect (tests.TestCase_RetevisRB17A) Testing Retevis RB17A detect ... ok test_edges (tests.TestCase_RetevisRB17A) Testing Retevis RB17A edges ... skipped 'No mutable memory locations found' test_settings (tests.TestCase_RetevisRB17A) Testing Retevis RB17A settings ... ok test_banks (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D banks ... ok test_brute_force (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D brute force ... ok test_clone (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D clone ... ok test_copy_all (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D copy all ... ok test_detect (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D detect ... ok test_edges (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D edges ... ok test_settings (tests.TestCase_YaesuFT70D) Testing Yaesu FT-70D settings ... ok test_banks (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 brute force ... ok test_clone (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 clone ... ok test_copy_all (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 copy all ... ok test_detect (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 detect ... ok test_edges (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 edges ... ok test_settings (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 settings ... ok test_banks (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B brute force ... ok test_clone (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B clone ... ok test_copy_all (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B copy all ... ok test_detect (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B detect ... ok test_edges (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B edges ... ok test_settings (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B settings ... ok test_banks (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 banks ... ok test_brute_force (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 brute force ... ok test_clone (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 clone ... ok test_copy_all (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 copy all ... ok test_detect (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 detect ... ok test_edges (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 edges ... ok test_settings (tests.TestCase_YaesuVX5) Testing Yaesu VX-5 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_TYTTH9800) Testing TYT TH-9800 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTH9800) Testing TYT TH-9800 brute force ... ok test_clone (tests.TestCase_TYTTH9800) Testing TYT TH-9800 clone ... ok test_copy_all (tests.TestCase_TYTTH9800) Testing TYT TH-9800 copy all ... ok test_detect (tests.TestCase_TYTTH9800) Testing TYT TH-9800 detect ... ok test_edges (tests.TestCase_TYTTH9800) Testing TYT TH-9800 edges ... ok test_settings (tests.TestCase_TYTTH9800) Testing TYT TH-9800 settings ... ok test_banks (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P brute force ... ok test_clone (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P clone ... ok test_copy_all (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P copy all ... ok test_detect (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P detect ... ok test_edges (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P edges ... ok test_settings (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P settings ... ok test_banks (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 brute force ... ok test_clone (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 clone ... ok test_copy_all (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 copy all ... ok test_detect (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 detect ... ok test_edges (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 edges ... ok test_settings (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 settings ... ok test_banks (tests.TestCase_RetevisRB26) Testing Retevis RB26 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRB26) Testing Retevis RB26 brute force ... ok test_clone (tests.TestCase_RetevisRB26) Testing Retevis RB26 clone ... ok test_copy_all (tests.TestCase_RetevisRB26) Testing Retevis RB26 copy all ... ok test_detect (tests.TestCase_RetevisRB26) Testing Retevis RB26 detect ... ok test_edges (tests.TestCase_RetevisRB26) Testing Retevis RB26 edges ... skipped 'No mutable memory locations found' test_settings (tests.TestCase_RetevisRB26) Testing Retevis RB26 settings ... ok test_banks (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M brute force ... ok test_clone (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M clone ... ok test_copy_all (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M copy all ... ok test_detect (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M detect ... ok test_edges (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M edges ... ok test_settings (tests.TestCase_YaesuFT7100M) Testing Yaesu FT-7100M settings ... ok test_banks (tests.TestCase_IcomID31A) Testing Icom ID-31A banks ... ok test_brute_force (tests.TestCase_IcomID31A) Testing Icom ID-31A brute force ... ok test_clone (tests.TestCase_IcomID31A) Testing Icom ID-31A clone ... ok test_copy_all (tests.TestCase_IcomID31A) Testing Icom ID-31A copy all ... ok test_detect (tests.TestCase_IcomID31A) Testing Icom ID-31A detect ... ok test_edges (tests.TestCase_IcomID31A) Testing Icom ID-31A edges ... ok test_settings (tests.TestCase_IcomID31A) Testing Icom ID-31A settings ... ok test_banks (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B brute force ... ok test_clone (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B clone ... ok test_copy_all (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B copy all ... ok test_detect (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B detect ... ok test_edges (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B edges ... ok test_settings (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B settings ... ok test_banks (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 brute force ... ok test_clone (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 clone ... ok test_copy_all (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 copy all ... ok test_detect (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 detect ... ok test_edges (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 edges ... ok test_settings (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 settings ... ok test_banks (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 brute force ... ok test_clone (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 clone ... ok test_copy_all (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 copy all ... ok test_detect (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 detect ... ok test_edges (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 edges ... ok test_settings (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 banks ... ok test_brute_force (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 brute force ... ok test_clone (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 clone ... ok test_copy_all (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 copy all ... ok test_detect (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 detect ... ok test_edges (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 edges ... ok test_settings (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 settings ... ok test_banks (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M brute force ... ok test_clone (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M clone ... ok test_copy_all (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M copy all ... ok test_detect (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M detect ... ok test_edges (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M edges ... ok test_settings (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_RetevisRT1) Testing Retevis RT1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT1) Testing Retevis RT1 brute force ... ok test_clone (tests.TestCase_RetevisRT1) Testing Retevis RT1 clone ... ok test_copy_all (tests.TestCase_RetevisRT1) Testing Retevis RT1 copy all ... ok test_detect (tests.TestCase_RetevisRT1) Testing Retevis RT1 detect ... ok test_edges (tests.TestCase_RetevisRT1) Testing Retevis RT1 edges ... ok test_settings (tests.TestCase_RetevisRT1) Testing Retevis RT1 settings ... ok test_banks (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 banks ... ok test_brute_force (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 brute force ... ok test_clone (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 clone ... ok test_copy_all (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 copy all ... ok test_detect (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 detect ... ok test_edges (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 edges ... ok test_settings (tests.TestCase_YaesuFT78007900) Testing Yaesu FT-7800/7900 settings ... ok test_banks (tests.TestCase_IcomIC208H) Testing Icom IC-208H banks ... ok test_brute_force (tests.TestCase_IcomIC208H) Testing Icom IC-208H brute force ... ok test_clone (tests.TestCase_IcomIC208H) Testing Icom IC-208H clone ... ok test_copy_all (tests.TestCase_IcomIC208H) Testing Icom IC-208H copy all ... ok test_detect (tests.TestCase_IcomIC208H) Testing Icom IC-208H detect ... ok test_edges (tests.TestCase_IcomIC208H) Testing Icom IC-208H edges ... ok test_settings (tests.TestCase_IcomIC208H) Testing Icom IC-208H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R brute force ... ok test_clone (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R clone ... ok test_copy_all (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R copy all ... ok test_detect (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R detect ... ok test_edges (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R edges ... ok test_settings (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M brute force ... ok test_clone (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M clone ... ok test_copy_all (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M copy all ... ok test_detect (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M detect ... ok test_edges (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M edges ... ok test_settings (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode brute force ... ok test_clone (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode clone ... ok test_copy_all (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode copy all ... ok test_detect (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode detect ... ok test_edges (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode edges ... ok test_settings (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode settings ... ok test_banks (tests.TestCase_RetevisRT16) Testing Retevis RT16 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT16) Testing Retevis RT16 brute force ... ok test_clone (tests.TestCase_RetevisRT16) Testing Retevis RT16 clone ... ok test_copy_all (tests.TestCase_RetevisRT16) Testing Retevis RT16 copy all ... ok test_detect (tests.TestCase_RetevisRT16) Testing Retevis RT16 detect ... ok test_edges (tests.TestCase_RetevisRT16) Testing Retevis RT16 edges ... skipped 'No mutable memory locations found' test_settings (tests.TestCase_RetevisRT16) Testing Retevis RT16 settings ... ok test_banks (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 brute force ... ok test_clone (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 clone ... ok test_copy_all (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 copy all ... ok test_detect (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 detect ... ok test_edges (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 edges ... ok test_settings (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 settings ... ok test_banks (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 banks ... ok test_brute_force (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 brute force ... ok test_clone (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 clone ... ok test_copy_all (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 copy all ... ok test_detect (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 detect ... ok test_edges (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 edges ... ok test_settings (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 brute force ... ok test_clone (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 clone ... ok test_copy_all (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 copy all ... ok test_detect (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 detect ... ok test_edges (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 edges ... ok test_settings (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 settings ... ok test_banks (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 brute force ... ok test_clone (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 clone ... ok test_copy_all (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 copy all ... ok test_detect (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 detect ... ok test_edges (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 edges ... ok test_settings (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 settings ... ok test_banks (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H brute force ... ok test_clone (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H clone ... ok test_copy_all (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H copy all ... ok test_detect (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H detect ... ok test_edges (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H edges ... ok test_settings (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_RetevisRT21) Testing Retevis RT21 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT21) Testing Retevis RT21 brute force ... ok test_clone (tests.TestCase_RetevisRT21) Testing Retevis RT21 clone ... ok test_copy_all (tests.TestCase_RetevisRT21) Testing Retevis RT21 copy all ... ok test_detect (tests.TestCase_RetevisRT21) Testing Retevis RT21 detect ... ok test_edges (tests.TestCase_RetevisRT21) Testing Retevis RT21 edges ... ok test_settings (tests.TestCase_RetevisRT21) Testing Retevis RT21 settings ... ok test_banks (tests.TestCase_IcomID51) Testing Icom ID-51 banks ... ok test_brute_force (tests.TestCase_IcomID51) Testing Icom ID-51 brute force ... ok test_clone (tests.TestCase_IcomID51) Testing Icom ID-51 clone ... ok test_copy_all (tests.TestCase_IcomID51) Testing Icom ID-51 copy all ... ok test_detect (tests.TestCase_IcomID51) Testing Icom ID-51 detect ... ok test_edges (tests.TestCase_IcomID51) Testing Icom ID-51 edges ... ok test_settings (tests.TestCase_IcomID51) Testing Icom ID-51 settings ... ok test_banks (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND brute force ... ok test_clone (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND clone ... ok test_copy_all (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND copy all ... ok test_detect (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND detect ... ok test_edges (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND edges ... ok test_settings (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND settings ... ok test_banks (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 brute force ... ok test_clone (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 clone ... ok test_copy_all (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 copy all ... ok test_detect (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 detect ... ok test_edges (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 edges ... ok test_settings (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 settings ... ok test_banks (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H banks ... ok test_brute_force (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H brute force ... ok test_clone (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H clone ... ok test_copy_all (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H copy all ... ok test_detect (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H detect ... ok test_edges (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H edges ... ok test_settings (tests.TestCase_IcomIC2200H) Testing Icom IC-2200H settings ... ok test_banks (tests.TestCase_TYTTHUV88) Testing TYT TH-UV88 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUV88) Testing TYT TH-UV88 brute force ... ok test_clone (tests.TestCase_TYTTHUV88) Testing TYT TH-UV88 clone ... ok test_copy_all (tests.TestCase_TYTTHUV88) Testing TYT TH-UV88 copy all ... ok test_detect (tests.TestCase_TYTTHUV88) Testing TYT TH-UV88 detect ... ok test_edges (tests.TestCase_TYTTHUV88) Testing TYT TH-UV88 edges ... ok test_settings (tests.TestCase_TYTTHUV88) Testing TYT TH-UV88 settings ... ok test_banks (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode brute force ... ok test_clone (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode clone ... ok test_copy_all (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode copy all ... ok test_detect (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode detect ... ok test_edges (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode edges ... ok test_settings (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode settings ... ok test_banks (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR banks ... ok test_brute_force (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR brute force ... ok test_clone (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR clone ... ok test_copy_all (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR copy all ... ok test_detect (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR detect ... ok test_edges (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR edges ... ok test_settings (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR settings ... ok test_banks (tests.TestCase_RetevisRT22) Testing Retevis RT22 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT22) Testing Retevis RT22 brute force ... ok test_clone (tests.TestCase_RetevisRT22) Testing Retevis RT22 clone ... ok test_copy_all (tests.TestCase_RetevisRT22) Testing Retevis RT22 copy all ... ok test_detect (tests.TestCase_RetevisRT22) Testing Retevis RT22 detect ... ok test_edges (tests.TestCase_RetevisRT22) Testing Retevis RT22 edges ... ok test_settings (tests.TestCase_RetevisRT22) Testing Retevis RT22 settings ... ok test_banks (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) brute force ... ok test_clone (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) clone ... ok test_copy_all (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) copy all ... ok test_detect (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) detect ... ok test_edges (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) edges ... ok test_settings (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) settings ... ok test_banks (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus banks ... ok test_brute_force (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus brute force ... ok test_clone (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus clone ... ok test_copy_all (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus copy all ... ok test_detect (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus detect ... ok test_edges (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus edges ... ok test_settings (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus settings ... ok test_banks (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D banks ... ok test_brute_force (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D brute force ... ok test_clone (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D clone ... ok test_copy_all (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D copy all ... ok test_detect (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D detect ... ok test_edges (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D edges ... ok test_settings (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D settings ... ok test_banks (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode brute force ... ok test_clone (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode clone ... ok test_copy_all (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode copy all ... ok test_detect (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode detect ... ok test_edges (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode edges ... ok test_settings (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode settings ... ok test_banks (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H banks ... ok test_brute_force (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H brute force ... ok test_clone (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H clone ... ok test_copy_all (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H copy all ... ok test_detect (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H detect ... ok test_edges (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H edges ... ok test_settings (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H settings ... ok test_banks (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 brute force ... ok test_clone (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 clone ... ok test_copy_all (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 copy all ... ok test_detect (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 detect ... ok test_edges (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 edges ... ok test_settings (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 settings ... ok test_banks (tests.TestCase_RetevisRT22FRS) Testing Retevis RT22FRS banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT22FRS) Testing Retevis RT22FRS brute force ... ok test_clone (tests.TestCase_RetevisRT22FRS) Testing Retevis RT22FRS clone ... ok test_copy_all (tests.TestCase_RetevisRT22FRS) Testing Retevis RT22FRS copy all ... ok test_detect (tests.TestCase_RetevisRT22FRS) Testing Retevis RT22FRS detect ... ok test_edges (tests.TestCase_RetevisRT22FRS) Testing Retevis RT22FRS edges ... ok test_settings (tests.TestCase_RetevisRT22FRS) Testing Retevis RT22FRS settings ... ok test_banks (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 brute force ... ok test_clone (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 clone ... ok test_copy_all (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 copy all ... ok test_detect (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 detect ... ok test_edges (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 edges ... ok test_settings (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 settings ... ok test_banks (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode brute force ... ok test_clone (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode clone ... ok test_copy_all (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode copy all ... ok test_detect (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode detect ... ok test_edges (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode edges ... ok test_settings (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode settings ... ok test_banks (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H banks ... ok test_brute_force (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H brute force ... ok test_clone (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H clone ... ok test_copy_all (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H copy all ... ok test_detect (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H detect ... ok test_edges (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H edges ... ok test_settings (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 brute force ... ok test_clone (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 clone ... ok test_copy_all (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 copy all ... ok test_detect (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 detect ... ok test_edges (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 edges ... ok test_settings (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 settings ... ok test_banks (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE banks ... ok test_brute_force (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE brute force ... ok test_clone (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE clone ... ok test_copy_all (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE copy all ... ok test_detect (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE detect ... ok test_edges (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE edges ... ok test_settings (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE settings ... ok test_banks (tests.TestCase_IcomID800H) Testing Icom ID-800H banks ... ok test_brute_force (tests.TestCase_IcomID800H) Testing Icom ID-800H brute force ... ok test_clone (tests.TestCase_IcomID800H) Testing Icom ID-800H clone ... ok test_copy_all (tests.TestCase_IcomID800H) Testing Icom ID-800H copy all ... ok test_detect (tests.TestCase_IcomID800H) Testing Icom ID-800H detect ... ok test_edges (tests.TestCase_IcomID800H) Testing Icom ID-800H edges ... ok test_settings (tests.TestCase_IcomID800H) Testing Icom ID-800H settings ... ok test_banks (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R banks ... ok test_brute_force (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R brute force ... ok test_clone (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R clone ... ok test_copy_all (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R copy all ... ok test_detect (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R detect ... ok test_edges (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R edges ... ok test_settings (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R settings ... ok test_banks (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 brute force ... ok test_clone (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 clone ... ok test_copy_all (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 copy all ... ok test_detect (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 detect ... ok test_edges (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 edges ... ok test_settings (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 settings ... ok test_banks (tests.TestCase_RetevisRT22S) Testing Retevis RT22S banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT22S) Testing Retevis RT22S brute force ... ok test_clone (tests.TestCase_RetevisRT22S) Testing Retevis RT22S clone ... ok test_copy_all (tests.TestCase_RetevisRT22S) Testing Retevis RT22S copy all ... ok test_detect (tests.TestCase_RetevisRT22S) Testing Retevis RT22S detect ... ok test_edges (tests.TestCase_RetevisRT22S) Testing Retevis RT22S edges ... skipped 'No mutable memory locations found' test_settings (tests.TestCase_RetevisRT22S) Testing Retevis RT22S settings ... ok test_banks (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 brute force ... ok test_clone (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 clone ... ok test_copy_all (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 copy all ... ok test_detect (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 detect ... ok test_edges (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 edges ... ok test_settings (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 settings ... ok test_banks (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV brute force ... ok test_clone (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV clone ... ok test_copy_all (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV copy all ... ok test_detect (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV detect ... ok test_edges (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV edges ... ok test_settings (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV settings ... ok test_banks (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A banks ... ok test_brute_force (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A brute force ... ok test_clone (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A clone ... ok test_copy_all (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A copy all ... ok test_detect (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A detect ... ok test_edges (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A edges ... ok test_settings (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A settings ... ok test_banks (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 brute force ... ok test_clone (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 clone ... ok test_copy_all (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 copy all ... ok test_detect (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 detect ... ok test_edges (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 edges ... ok test_settings (tests.TestCase_BTECHUV5X3) Testing BTECH UV-5X3 settings ... ok test_banks (tests.TestCase_VertexStandardFTL2011) Testing Vertex Standard FTL-2011 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_VertexStandardFTL2011) Testing Vertex Standard FTL-2011 brute force ... ok test_clone (tests.TestCase_VertexStandardFTL2011) Testing Vertex Standard FTL-2011 clone ... ok test_copy_all (tests.TestCase_VertexStandardFTL2011) Testing Vertex Standard FTL-2011 copy all ... ok test_detect (tests.TestCase_VertexStandardFTL2011) Testing Vertex Standard FTL-2011 detect ... ok test_edges (tests.TestCase_VertexStandardFTL2011) Testing Vertex Standard FTL-2011 edges ... ok test_settings (tests.TestCase_VertexStandardFTL2011) Testing Vertex Standard FTL-2011 settings ... ok test_banks (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M brute force ... ok test_clone (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M clone ... ok test_copy_all (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M copy all ... ok test_detect (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M detect ... ok test_edges (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M edges ... ok test_settings (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomID880H) Testing Icom ID-880H banks ... ok test_brute_force (tests.TestCase_IcomID880H) Testing Icom ID-880H brute force ... ok test_clone (tests.TestCase_IcomID880H) Testing Icom ID-880H clone ... ok test_copy_all (tests.TestCase_IcomID880H) Testing Icom ID-880H copy all ... ok test_detect (tests.TestCase_IcomID880H) Testing Icom ID-880H detect ... ok test_edges (tests.TestCase_IcomID880H) Testing Icom ID-880H edges ... ok test_settings (tests.TestCase_IcomID880H) Testing Icom ID-880H settings ... ok test_banks (tests.TestCase_RetevisRT23) Testing Retevis RT23 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT23) Testing Retevis RT23 brute force ... ok test_clone (tests.TestCase_RetevisRT23) Testing Retevis RT23 clone ... ok test_copy_all (tests.TestCase_RetevisRT23) Testing Retevis RT23 copy all ... ok test_detect (tests.TestCase_RetevisRT23) Testing Retevis RT23 detect ... ok test_edges (tests.TestCase_RetevisRT23) Testing Retevis RT23 edges ... ok test_settings (tests.TestCase_RetevisRT23) Testing Retevis RT23 settings ... ok test_banks (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R banks ... ok test_brute_force (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R brute force ... ok test_clone (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R clone ... ok test_copy_all (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R copy all ... ok test_detect (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R detect ... ok test_edges (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R edges ... ok test_settings (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R settings ... ok test_banks (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) brute force ... ok test_clone (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) clone ... ok test_copy_all (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) copy all ... ok test_detect (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) detect ... ok test_edges (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) edges ... ok test_settings (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) settings ... ok test_banks (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H banks ... ok test_brute_force (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H brute force ... ok test_clone (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H clone ... ok test_copy_all (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H copy all ... ok test_detect (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H detect ... ok test_edges (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H edges ... ok test_settings (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H settings ... ok test_banks (tests.TestCase_LeixenVV898) Testing Leixen VV-898 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_LeixenVV898) Testing Leixen VV-898 brute force ... ok test_clone (tests.TestCase_LeixenVV898) Testing Leixen VV-898 clone ... ok test_copy_all (tests.TestCase_LeixenVV898) Testing Leixen VV-898 copy all ... ok test_detect (tests.TestCase_LeixenVV898) Testing Leixen VV-898 detect ... ok test_edges (tests.TestCase_LeixenVV898) Testing Leixen VV-898 edges ... ok test_settings (tests.TestCase_LeixenVV898) Testing Leixen VV-898 settings ... ok test_banks (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 brute force ... ok test_clone (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 clone ... ok test_copy_all (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 copy all ... ok test_detect (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 detect ... ok test_edges (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 edges ... ok test_settings (tests.TestCase_BaofengBF888) Testing Baofeng BF-888 settings ... ok test_banks (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 brute force ... ok test_clone (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 clone ... ok test_copy_all (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 copy all ... ok test_detect (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 detect ... ok test_edges (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 edges ... ok test_settings (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R banks ... ok test_brute_force (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R brute force ... ok test_clone (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R clone ... ok test_copy_all (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R copy all ... ok test_detect (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R detect ... ok test_edges (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R edges ... ok test_settings (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R settings ... ok test_banks (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M brute force ... ok test_clone (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M clone ... ok test_copy_all (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M copy all ... ok test_detect (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M detect ... ok test_edges (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M edges ... ok test_settings (tests.TestCase_JetstreamJT220M) Testing Jetstream JT220M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_RetevisRT26) Testing Retevis RT26 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT26) Testing Retevis RT26 brute force ... ok test_clone (tests.TestCase_RetevisRT26) Testing Retevis RT26 clone ... ok test_copy_all (tests.TestCase_RetevisRT26) Testing Retevis RT26 copy all ... ok test_detect (tests.TestCase_RetevisRT26) Testing Retevis RT26 detect ... ok test_edges (tests.TestCase_RetevisRT26) Testing Retevis RT26 edges ... ok test_settings (tests.TestCase_RetevisRT26) Testing Retevis RT26 settings ... ok test_banks (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 banks ... ok test_brute_force (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 brute force ... ok test_clone (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 clone ... ok test_copy_all (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 copy all ... ok test_detect (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 detect ... ok test_edges (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 edges ... ok test_settings (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S brute force ... ok test_clone (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S clone ... ok test_copy_all (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S copy all ... ok test_detect (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S detect ... ok test_edges (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S edges ... ok test_settings (tests.TestCase_LeixenVV898S) Testing Leixen VV-898S settings ... ok test_banks (tests.TestCase_BaofengBFA58S) Testing Baofeng BF-A58S banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengBFA58S) Testing Baofeng BF-A58S brute force ... ok test_clone (tests.TestCase_BaofengBFA58S) Testing Baofeng BF-A58S clone ... ok test_copy_all (tests.TestCase_BaofengBFA58S) Testing Baofeng BF-A58S copy all ... ok test_detect (tests.TestCase_BaofengBFA58S) Testing Baofeng BF-A58S detect ... ok test_edges (tests.TestCase_BaofengBFA58S) Testing Baofeng BF-A58S edges ... ok test_settings (tests.TestCase_BaofengBFA58S) Testing Baofeng BF-A58S settings ... ok test_banks (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 brute force ... ok test_clone (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 clone ... ok test_copy_all (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 copy all ... ok test_detect (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 detect ... ok test_edges (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 edges ... ok test_settings (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 settings ... ok test_banks (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M brute force ... ok test_clone (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M clone ... ok test_copy_all (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M copy all ... ok test_detect (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M detect ... ok test_edges (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M edges ... ok test_settings (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M settings ... ok test_banks (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D brute force ... ok test_clone (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D clone ... ok test_copy_all (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D copy all ... ok test_detect (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D detect ... ok test_edges (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D edges ... ok test_settings (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D settings ... ok test_banks (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 brute force ... ok test_clone (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 clone ... ok test_copy_all (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 copy all ... ok test_detect (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 detect ... ok test_edges (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 edges ... ok test_settings (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BaofengBFT1) Testing Baofeng BF-T1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengBFT1) Testing Baofeng BF-T1 brute force ... ok test_clone (tests.TestCase_BaofengBFT1) Testing Baofeng BF-T1 clone ... ok test_copy_all (tests.TestCase_BaofengBFT1) Testing Baofeng BF-T1 copy all ... ok test_detect (tests.TestCase_BaofengBFT1) Testing Baofeng BF-T1 detect ... ok test_edges (tests.TestCase_BaofengBFT1) Testing Baofeng BF-T1 edges ... ok test_settings (tests.TestCase_BaofengBFT1) Testing Baofeng BF-T1 settings ... ok test_banks (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH brute force ... ok test_clone (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH clone ... ok test_copy_all (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH copy all ... ok test_detect (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH detect ... ok test_edges (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH edges ... ok test_settings (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH settings ... ok test_banks (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR banks ... ok test_brute_force (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR brute force ... ok test_clone (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR clone ... ok test_copy_all (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR copy all ... ok test_detect (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR detect ... ok test_edges (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR edges ... ok test_settings (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR settings ... ok test_banks (tests.TestCase_MidlandDBR2500) Testing Midland DBR2500 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_MidlandDBR2500) Testing Midland DBR2500 brute force ... ok test_clone (tests.TestCase_MidlandDBR2500) Testing Midland DBR2500 clone ... ok test_copy_all (tests.TestCase_MidlandDBR2500) Testing Midland DBR2500 copy all ... ok test_detect (tests.TestCase_MidlandDBR2500) Testing Midland DBR2500 detect ... ok test_edges (tests.TestCase_MidlandDBR2500) Testing Midland DBR2500 edges ... ok test_settings (tests.TestCase_MidlandDBR2500) Testing Midland DBR2500 settings ... ok test_banks (tests.TestCase_BaofengBFT8) Testing Baofeng BF-T8 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengBFT8) Testing Baofeng BF-T8 brute force ... ok test_clone (tests.TestCase_BaofengBFT8) Testing Baofeng BF-T8 clone ... ok test_copy_all (tests.TestCase_BaofengBFT8) Testing Baofeng BF-T8 copy all ... ok test_detect (tests.TestCase_BaofengBFT8) Testing Baofeng BF-T8 detect ... ok test_edges (tests.TestCase_BaofengBFT8) Testing Baofeng BF-T8 edges ... ok test_settings (tests.TestCase_BaofengBFT8) Testing Baofeng BF-T8 settings ... ok test_banks (tests.TestCase_KYDIP620) Testing KYD IP-620 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KYDIP620) Testing KYD IP-620 brute force ... ok test_clone (tests.TestCase_KYDIP620) Testing KYD IP-620 clone ... ok test_copy_all (tests.TestCase_KYDIP620) Testing KYD IP-620 copy all ... ok test_detect (tests.TestCase_KYDIP620) Testing KYD IP-620 detect ... ok test_edges (tests.TestCase_KYDIP620) Testing KYD IP-620 edges ... ok test_settings (tests.TestCase_KYDIP620) Testing KYD IP-620 settings ... ok test_banks (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE banks ... ok test_brute_force (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE brute force ... ok test_clone (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE clone ... ok test_copy_all (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE copy all ... ok test_detect (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE detect ... ok test_edges (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE edges ... ok test_settings (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE settings ... ok test_banks (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D banks ... ok test_brute_force (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D brute force ... ok test_clone (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D clone ... ok test_copy_all (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D copy all ... ok test_detect (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D detect ... ok test_edges (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D edges ... ok test_settings (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D settings ... ok test_banks (tests.TestCase_KYDNC630A) Testing KYD NC-630A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KYDNC630A) Testing KYD NC-630A brute force ... ok test_clone (tests.TestCase_KYDNC630A) Testing KYD NC-630A clone ... ok test_copy_all (tests.TestCase_KYDNC630A) Testing KYD NC-630A copy all ... ok test_detect (tests.TestCase_KYDNC630A) Testing KYD NC-630A detect ... ok test_edges (tests.TestCase_KYDNC630A) Testing KYD NC-630A edges ... ok test_settings (tests.TestCase_KYDNC630A) Testing KYD NC-630A settings ... ok test_banks (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M brute force ... ok test_clone (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M clone ... ok test_copy_all (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M copy all ... ok test_detect (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M detect ... ok test_edges (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M edges ... ok test_settings (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M settings ... ok test_banks (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR banks ... ok test_brute_force (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR brute force ... ok test_clone (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR clone ... ok test_copy_all (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR copy all ... ok test_detect (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR detect ... ok test_edges (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR edges ... ok test_settings (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR settings ... ok test_banks (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R brute force ... ok test_clone (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R clone ... ok test_copy_all (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R copy all ... ok test_detect (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R detect ... ok test_edges (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R edges ... ok test_settings (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R settings ... skipped 'Settings not supported' test_banks (tests.TestCase_PuxingPX777) Testing Puxing PX-777 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_PuxingPX777) Testing Puxing PX-777 brute force ... ok test_clone (tests.TestCase_PuxingPX777) Testing Puxing PX-777 clone ... ok test_copy_all (tests.TestCase_PuxingPX777) Testing Puxing PX-777 copy all ... ok test_detect (tests.TestCase_PuxingPX777) Testing Puxing PX-777 detect ... ok test_edges (tests.TestCase_PuxingPX777) Testing Puxing PX-777 edges ... ok test_settings (tests.TestCase_PuxingPX777) Testing Puxing PX-777 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D banks ... ok test_brute_force (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D brute force ... ok test_clone (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D clone ... ok test_copy_all (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D copy all ... ok test_detect (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D detect ... ok test_edges (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D edges ... ok test_settings (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D settings ... ok test_banks (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D brute force ... ok test_clone (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D clone ... ok test_copy_all (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D copy all ... ok test_detect (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D detect ... ok test_edges (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D edges ... ok test_settings (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D settings ... skipped 'Settings not supported' ---------------------------------------------------------------------- Ran 1106 tests in 481.689s OK (skipped=156) struct memory { bbcd rx_freq[4]; bbcd tx_freq[4]; lbcd rx_tone[2]; lbcd tx_tone[2]; u8 unknown10:5, highpower:1, unknown11:2; u8 unknown20:4, narrow:1, unknown21:3; u8 unknown31:1, scanadd:1, unknown32:6; u8 unknown4; }; struct name { char name[7]; }; #seekto 0x0010; struct memory channels[128]; #seekto 0x08C0; struct name names[128]; #seekto 0x2020; struct memory vfo1; struct memory vfo2; style create: /chirp/.tox/style style installdeps: pep8==1.6.2, future style inst: /chirp/.tox/.tmp/package/1/chirp-0.3.0dev.zip style installed: DEPRECATION: Python 2.7 will reach the end of its life on January 1st, 2020. Please upgrade your Python as Python 2.7 won't be maintained after that date. A future version of pip will drop support for Python 2.7.,chirp==0.3.0.dev0,configparser==3.7.4,contextlib2==0.5.5,filelock==3.0.12,future==0.15.2,importlib-metadata==0.18,Mako==1.0.3,MarkupSafe==0.23,mercurial==3.7.3,packaging==19.0,pathlib2==2.3.4,pep8==1.6.2,pluggy==0.12.0,py==1.8.0,pygobject==3.20.0,pyparsing==2.4.0,pyserial==3.0.1,scandir==1.10.0,six==1.12.0,toml==0.10.0,tox==3.13.2,virtualenv==16.6.1,zipp==0.5.2 style run-test-pre: PYTHONHASHSEED='4185700940' style run-test: commands[0] | python ./tools/cpep8.py ___________________________________ summary ____________________________________ unit: commands succeeded driver: commands succeeded style: commands succeeded congratulations :) Email was triggered for: Success Sending email for trigger: Success

1 0

[chirp_devel] Python3
by Nathan Deckinga 13 Aug '21

13 Aug '21

Howdy, I'm sure this is something that has been asked about before, but is anyone working on a Python3 port or is there a reason that is not possible? If someone is working on it, I would love to see if I could help with the effort. I'm new to ham radio (and CHIRP), but not to FOSS or Python. Nathan KI5QLY

2 1

Re: [chirp_devel] [PATCH] [UV-5G] Add support for Radioddity UV-5G/UV-5X
by Ian McBride 12 Aug '21

12 Aug '21

I have recently purchased a pair of UV-5X radios and I must say I am rather disappointed in the approach in CHIRP and the OEM for implementing the programmed channels in the UV-5X. Baofeng/Pofung seems to be waking up to the idea that people want to be able to program channels above 30 with their own custom channels within the GMRS frequency set. The approach being taken in the code is that 1-30 are locked to what have become the customary GMRS channels. I read in issue 9235 (https://chirp.danplanet.com/issues/9235) that the reason this is so is because it is a GMRS radio and that the TX channels are locked this way. I think this is the wrong approach. If you look at Part 95, GMRS is frequency limited and power and bandwidth regulated based on frequency but it is not regulated to what channel in a radio has a particular frequency. I think the licensee would be better served if the channel's power limit, bandwidth limit, and TX frequency were driven by the RX frequency being set rather than the channel being written. I have been able to program channels over 30 by hacking around the OEM programming software and editing the XML directly then loading it. My radio has 1-30 as the "standard channels" with no CTCSS and then 31-52 as a repeat of the 1-22 with a CTCSS code for my radios in my family set. I have no need of repeater channels 23-30 with custom tones but there are people who are looking for this. I think a different logic approach should be considered. On memory write, the software would follow logic like this: HIGH_POWER_SIMPLEX_FREQUENCIES = [462.5625, 462.5875, 462.6125, 462.6375, 462.6625, 462.6875, 462.7125] LOW_POWER_SIMPLEX_FREQUENCIES = [467.5625, 467.5875, 467.6125, 467.6375, 467.6625, 467.6875, 467.7125] HIGH_POWER_REPEATER_FREQUENCIES = [462.5500, 462.5750, 462.6000, 462.6250, 462.6500, 462.6750, 462.7000, 462.7250] if the radio is a GMRS radio if freq in repeater_frequency set // high power repeater capable channels // allow none/off/+ duplex if duplex == '-' then log error and set to off if duplex == 'split' then log error and set to off if duplex == '+' then set offset to 50000 allow high and low power allow wideband and narrowband TX else if freq in low_power_simplex_frequency set // low power simplex channels // allow none/off duplex if duplex == '-' then log error and set to off if duplex == '+' then log error and set to off if duplex == 'split' then log error and set to off allow only low power allow only narrowband TX else if freq in high_power_simplex_frequency set // high power simplex channels // allow none/off duplex if duplex == '-' then log error and set to off if duplex == '+' then log error and set to off if duplex == 'split' then log error and set to off allow high and low power allow wideband and narrowband TX else duplex = off offset = 0 end if end if This set of rules follows the FCC regulations for GMRS in Part 95. It would make the radios infinitely more flexible than with what is in there now. This approach has the interests of the user at heart while maintaining compliance. I'd like to get some feedback on this before I open an issue and attempt to implement this. I think this would be a great issue to work on in CHIRP to get some exposure to this type of application. I'm a corporate application developer by trade so we don't see a whole lot of GTK+ front ends interfacing with python so it has my interest. I also have the radio to test it on. Thank you for any consideration. Ian McBride

2 2

[chirp_devel] [PATCH] [UV-5G] Allow Programming GMRS TX/RX Frequencies On All Channels
by Jim Unroe 12 Aug '21

12 Aug '21

1 0

Re: [chirp_devel] [PATCH 2 of 2] [RT87] Add Retevis RT87
by Jim Unroe 04 Aug '21

04 Aug '21

CHIRP Radio Images (*.img) file to use for testing. Jim KC9HI On Wed, Aug 4, 2021 at 8:57 PM Jim Unroe <Rock.Unroe(a)gmail.com> wrote:

1 0

[chirp_devel] [PATCH 2 of 2] [RT87] Add Retevis RT87
by Jim Unroe 04 Aug '21

04 Aug '21

1 0

[chirp_devel] [PATCH 1 of 2] Add Support for RadioSettingValueInteger() in mem.extra
by Jim Unroe 04 Aug '21

04 Aug '21

1 0

[chirp_devel] [PATCH] [UV-5G] Fix Incorrect Offset for Repeater Channels
by Jim Unroe 04 Aug '21

04 Aug '21

1 0