Developers

Download

developers@lists.chirpmyradio.com

September 2020

11 participants
19 discussions

[chirp_devel] Patch for #8233, Ic-2730
by Rick (AA0RD) DeWitt 11 Sep '20

11 Sep '20

Patch for issue #8233, makes IC-2730 tone modes fully CHIRP compliant. Cross mode now allows Tone->Tone, Tone->DTCS, DTCS>-Tone We need to edit the "DevelopersToneModes" Wiki page, "Icom/Kenwood style" paragraph to note that the Icom IC-2730A actually DOES support two separate TX and RX tones (TON.TSQ mode in the radio). I can do that if permission is granted....:-\ -- Rick DeWitt AA0RD Sequim, Washington, USA 98382 (360) 681-3494

1 0

[chirp_devel] Add new Wiki file, consolidate others
by Bernhard Hailer 10 Sep '20

10 Sep '20

Hi Dan / all, I'd like to add a new file to the Wiki library, and later also to edit / consolidate some others. I can already edit; do I need extra privileges to add new files or to remove others? This simple short one, "Running Chirp under Windows" would be added: h1. Running CHIRP Under Windows {{>toc}} Running Chirp under Windows is pretty straight-forward, but it has some traps to offer. You can run into a few situations in which a little doing is needed before Chirp starts correctly. h2. Corrupt Chirp configuration file If Chirp just does nothing when you try to start it, then its configuration file might have been damaged: Windows 10 has a bad habit of corrupting it. Solution: Delete the chirp.config file. The next time CHIRP is loaded, a new chirp.config file will be created. The chirp.config file is kept in the same folder as the debug.log file (it might be in C:\Users\<user>\AppData\Roaming\CHIRP\chirp.config). h2. Non-standard character in program path CHIRP won't load when the Windows user account has a special character (accented characters, umlauts, characters which aren't in the latin alphabet) in it. Solution: Put Chirp somewhere into a path which doesn't contain special characters. h2. You get an "Error opening file for writing: c:\program files (x86)\chirp\_ctypes.pyd" Solution: Run Chirp with Administrator privileges. Thanks and 73, Bernhard AE6YN

3 3

[chirp_devel] Patch for UV5R driver to fix communication on Ubuntu 16.04 with pl2303-based cables (fixes #4165)
by interfect＠gmail.com 10 Sep '20

10 Sep '20

Hello, Bernhard Hailer has asked me to resubmit my patch for the issue with modern Ubuntu serial drivers having DTR low, at least when the port isn't open, causing the radio to be in transmit mode and not ready to accept CHIRP's commands as soon as the port is open. This fixes #4165. Issue: https://chirp.danplanet.com/issues/4165 Original patch submission (did anybody get it?): http://intrepid.danplanet.com/pipermail/chirp_devel/2016-October/004329.html I tried to send this message earlier after subscribing to the list and clicking the confirmation link in the subscription e-mail, but I think web based confirmation is broken. When I sent the patch I got a message saying it was held for moderation because I wasn't a member of the list. I had to subscribe again and confirm by e-mail instead to actually get onto the list. Thanks, -Adam

3 4

[chirp_devel] Build test results: Successful
by Build System 08 Sep '20

08 Sep '20

Tested changes: Changes for Build #886 [Dan Smith <dsmith(a)danplanet.com>] Fix transposed GA-510 tones #7939 [Tom Hayward <tom(a)tomh.us>] [id880] Fix typo in charset definition. #281 [Tom Hayward <tom(a)tomh.us>] [thf6a] Support full charset (ASCII). Fixes #141 [Tom Hayward <tom(a)tomh.us>] [id880] Support full charset. Fixes #281 [Tom Hayward <tom(a)tomh.us>] [vx5] Support full charset (ASCII). Fixes #292 [Tom Hayward <tom(a)tomh.us>] [id31a] set used bit when creating new memory, clear when deleting. Fixes #269 [Tom Hayward <tom(a)tomh.us>] Support PyGTK < 2.22 in bank edit. Fixes #231 [Tom Hayward <tom(a)tomh.us>] [d710] [v71] [d72] Fix tone list (not all tones are supported). Fixes #212 [Dan Smith <dsmith(a)danplanet.com>] [vx7] Fix setting memory power levels on 220MHz band Fixes #214 [Dan Smith <dsmith(a)danplanet.com>] fips: Pennsylvania FIPS code was wrong. #117 [Marco Filippi <iz3gme.marco(a)gmail.com>] Consider lower bound frequency of each valid_band as valid Fix bug #181 [Tom Hayward <tom(a)tomh.us>] tmd700: allow 8-char names. Fixes #176 [Dan Smith <dsmith(a)danplanet.com>] Fix the "blind deletion" problem, as well as properly direct copy/paste Fixes #172 [David Griffith <dave(a)661.org>] Bug #155 fix: VX-7 1.25m power levels [David Griffith <dave(a)661.org>] New INSTALL and README files Fixes #122 [Tom Hayward <tom(a)tomh.us>] thd72: only use hardware flow on OS X. Fixes #166 [Marco Filippi <iz3gme.marco(a)gmail.com>] [FT817] Tone freq not set correctly Same as #88 for FT857, to avoid code duplication fix code have been moved from ft857 to its ancestor class Fix bug #163 [Tom Hayward <tom(a)tomh.us>] Fix Mac .app so paths with spaces work. Fixes Bug #145 Full log: [...truncated 672 lines...] test_copy_all (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus copy all ... ok test_detect (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus detect ... ok test_edges (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus edges ... ok test_settings (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus settings ... ok test_banks (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M brute force ... ok test_clone (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M clone ... ok test_copy_all (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M copy all ... ok test_detect (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M detect ... ok test_edges (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M edges ... ok test_settings (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M settings ... ok test_banks (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A banks ... ok test_brute_force (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A brute force ... ok test_clone (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A clone ... ok test_copy_all (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A copy all ... ok test_detect (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A detect ... ok test_edges (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A edges ... ok test_settings (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A settings ... ok test_banks (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 brute force ... ok test_clone (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 clone ... ok test_copy_all (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 copy all ... ok test_detect (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 detect ... ok test_edges (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 edges ... ok test_settings (tests.TestCase_YaesuFT817) Testing Yaesu FT-817 settings ... ok test_banks (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R brute force ... ok test_clone (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R clone ... ok test_copy_all (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R copy all ... ok test_detect (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R detect ... ok test_edges (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R edges ... ok test_settings (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R brute force ... ok test_clone (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R clone ... ok test_copy_all (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R copy all ... ok test_detect (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R detect ... ok test_edges (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R edges ... ok test_settings (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R settings ... ok test_banks (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 banks ... ok test_brute_force (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 brute force ... ok test_clone (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 clone ... ok test_copy_all (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 copy all ... ok test_detect (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 detect ... ok test_edges (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 edges ... ok test_settings (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 settings ... ok test_banks (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P brute force ... ok test_clone (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P clone ... ok test_copy_all (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P copy all ... ok test_detect (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P detect ... ok test_edges (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P edges ... ok test_settings (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P settings ... ok test_banks (tests.TestCase_AnyTone5888UV) Testing AnyTone 5888UV banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AnyTone5888UV) Testing AnyTone 5888UV brute force ... ok test_clone (tests.TestCase_AnyTone5888UV) Testing AnyTone 5888UV clone ... ok test_copy_all (tests.TestCase_AnyTone5888UV) Testing AnyTone 5888UV copy all ... ok test_detect (tests.TestCase_AnyTone5888UV) Testing AnyTone 5888UV detect ... ok test_edges (tests.TestCase_AnyTone5888UV) Testing AnyTone 5888UV edges ... ok test_settings (tests.TestCase_AnyTone5888UV) Testing AnyTone 5888UV settings ... ok test_banks (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND brute force ... ok test_clone (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND clone ... ok test_copy_all (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND copy all ... ok test_detect (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND detect ... ok test_edges (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND edges ... ok test_settings (tests.TestCase_YaesuFT817ND) Testing Yaesu FT-817ND settings ... ok test_banks (tests.TestCase_KYDNC630A) Testing KYD NC-630A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KYDNC630A) Testing KYD NC-630A brute force ... ok test_clone (tests.TestCase_KYDNC630A) Testing KYD NC-630A clone ... ok test_copy_all (tests.TestCase_KYDNC630A) Testing KYD NC-630A copy all ... ok test_detect (tests.TestCase_KYDNC630A) Testing KYD NC-630A detect ... ok test_edges (tests.TestCase_KYDNC630A) Testing KYD NC-630A edges ... ok test_settings (tests.TestCase_KYDNC630A) Testing KYD NC-630A settings ... ok test_banks (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 banks ... ok test_brute_force (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 brute force ... ok test_clone (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 clone ... ok test_copy_all (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 copy all ... ok test_detect (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 detect ... ok test_edges (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 edges ... ok test_settings (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_TYTTH350) Testing TYT TH-350 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTH350) Testing TYT TH-350 brute force ... ok test_clone (tests.TestCase_TYTTH350) Testing TYT TH-350 clone ... ok test_copy_all (tests.TestCase_TYTTH350) Testing TYT TH-350 copy all ... ok test_detect (tests.TestCase_TYTTH350) Testing TYT TH-350 detect ... ok test_edges (tests.TestCase_TYTTH350) Testing TYT TH-350 edges ... ok test_settings (tests.TestCase_TYTTH350) Testing TYT TH-350 settings ... ok test_banks (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H banks ... ok test_brute_force (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H brute force ... ok test_clone (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H clone ... ok test_copy_all (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H copy all ... ok test_detect (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H detect ... ok test_edges (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H edges ... ok test_settings (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H settings ... ok test_banks (tests.TestCase_PuxingPX777) Testing Puxing PX-777 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_PuxingPX777) Testing Puxing PX-777 brute force ... ok test_clone (tests.TestCase_PuxingPX777) Testing Puxing PX-777 clone ... ok test_copy_all (tests.TestCase_PuxingPX777) Testing Puxing PX-777 copy all ... ok test_detect (tests.TestCase_PuxingPX777) Testing Puxing PX-777 detect ... ok test_edges (tests.TestCase_PuxingPX777) Testing Puxing PX-777 edges ... ok test_settings (tests.TestCase_PuxingPX777) Testing Puxing PX-777 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M brute force ... ok test_clone (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M clone ... ok test_copy_all (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M copy all ... ok test_detect (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M detect ... ok test_edges (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M edges ... ok test_settings (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) brute force ... ok test_clone (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) clone ... ok test_copy_all (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) copy all ... ok test_detect (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) detect ... ok test_edges (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) edges ... ok test_settings (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) settings ... ok test_banks (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR banks ... ok test_brute_force (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR brute force ... ok test_clone (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR clone ... ok test_copy_all (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR copy all ... ok test_detect (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR detect ... ok test_edges (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR edges ... ok test_settings (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR settings ... ok test_banks (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R brute force ... ok test_clone (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R clone ... ok test_copy_all (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R copy all ... ok test_detect (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R detect ... ok test_edges (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R edges ... ok test_settings (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R settings ... ok test_banks (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) brute force ... ok test_clone (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) clone ... ok test_copy_all (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) copy all ... ok test_detect (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) detect ... ok test_edges (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) edges ... ok test_settings (tests.TestCase_YaesuFT817NDUS) Testing Yaesu FT-817ND (US) settings ... ok test_banks (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE banks ... ok test_brute_force (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE brute force ... ok test_clone (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE clone ... ok test_copy_all (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE copy all ... ok test_detect (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE detect ... ok test_edges (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE edges ... ok test_settings (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE settings ... ok test_banks (tests.TestCase_TYTTH7800) Testing TYT TH-7800 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTH7800) Testing TYT TH-7800 brute force ... ok test_clone (tests.TestCase_TYTTH7800) Testing TYT TH-7800 clone ... ok test_copy_all (tests.TestCase_TYTTH7800) Testing TYT TH-7800 copy all ... ok test_detect (tests.TestCase_TYTTH7800) Testing TYT TH-7800 detect ... ok test_edges (tests.TestCase_TYTTH7800) Testing TYT TH-7800 edges ... ok test_settings (tests.TestCase_TYTTH7800) Testing TYT TH-7800 settings ... ok test_banks (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G banks ... ok test_brute_force (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G brute force ... ok test_clone (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G clone ... ok test_copy_all (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G copy all ... ok test_detect (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G detect ... ok test_edges (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G edges ... ok test_settings (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G settings ... ok test_banks (tests.TestCase_AnyTone778UV) Testing AnyTone 778UV banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AnyTone778UV) Testing AnyTone 778UV brute force ... ok test_clone (tests.TestCase_AnyTone778UV) Testing AnyTone 778UV clone ... ok test_copy_all (tests.TestCase_AnyTone778UV) Testing AnyTone 778UV copy all ... ok test_detect (tests.TestCase_AnyTone778UV) Testing AnyTone 778UV detect ... ok test_edges (tests.TestCase_AnyTone778UV) Testing AnyTone 778UV edges ... ok test_settings (tests.TestCase_AnyTone778UV) Testing AnyTone 778UV settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M brute force ... ok test_clone (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M clone ... ok test_copy_all (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M copy all ... ok test_detect (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M detect ... ok test_edges (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M edges ... ok test_settings (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K brute force ... ok test_clone (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K clone ... ok test_copy_all (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K copy all ... ok test_detect (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K detect ... ok test_edges (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K edges ... ok test_settings (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K settings ... ok test_banks (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R brute force ... ok test_clone (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R clone ... ok test_copy_all (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R copy all ... ok test_detect (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R detect ... ok test_edges (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R edges ... ok test_settings (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R settings ... ok test_banks (tests.TestCase_IcomICP7) Testing Icom IC-P7 banks ... ok test_brute_force (tests.TestCase_IcomICP7) Testing Icom IC-P7 brute force ... ok test_clone (tests.TestCase_IcomICP7) Testing Icom IC-P7 clone ... ok test_copy_all (tests.TestCase_IcomICP7) Testing Icom IC-P7 copy all ... ok test_detect (tests.TestCase_IcomICP7) Testing Icom IC-P7 detect ... ok test_edges (tests.TestCase_IcomICP7) Testing Icom IC-P7 edges ... ok test_settings (tests.TestCase_IcomICP7) Testing Icom IC-P7 settings ... ok test_banks (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 brute force ... ok test_clone (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 clone ... ok test_copy_all (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 copy all ... ok test_detect (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 detect ... ok test_edges (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 edges ... ok test_settings (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 settings ... ok test_banks (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 brute force ... ok test_clone (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 clone ... ok test_copy_all (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 copy all ... ok test_detect (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 detect ... ok test_edges (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 edges ... ok test_settings (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus brute force ... ok test_clone (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus clone ... ok test_copy_all (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus copy all ... ok test_detect (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus detect ... ok test_edges (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus edges ... ok test_settings (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus settings ... ok test_banks (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 brute force ... ok test_clone (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 clone ... ok test_copy_all (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 copy all ... ok test_detect (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 detect ... ok test_edges (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 edges ... ok test_settings (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 settings ... ok test_banks (tests.TestCase_TYTTH9800) Testing TYT TH-9800 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTH9800) Testing TYT TH-9800 brute force ... ok test_clone (tests.TestCase_TYTTH9800) Testing TYT TH-9800 clone ... ok test_copy_all (tests.TestCase_TYTTH9800) Testing TYT TH-9800 copy all ... ok test_detect (tests.TestCase_TYTTH9800) Testing TYT TH-9800 detect ... ok test_edges (tests.TestCase_TYTTH9800) Testing TYT TH-9800 edges ... ok test_settings (tests.TestCase_TYTTH9800) Testing TYT TH-9800 settings ... ok test_banks (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R brute force ... ok test_clone (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R clone ... ok test_copy_all (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R copy all ... ok test_detect (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R detect ... ok test_edges (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R edges ... ok test_settings (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R settings ... ok test_banks (tests.TestCase_KenwoodTK3180K2) Testing Kenwood TK-3180K2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTK3180K2) Testing Kenwood TK-3180K2 brute force ... ok test_clone (tests.TestCase_KenwoodTK3180K2) Testing Kenwood TK-3180K2 clone ... ok test_copy_all (tests.TestCase_KenwoodTK3180K2) Testing Kenwood TK-3180K2 copy all ... ok test_detect (tests.TestCase_KenwoodTK3180K2) Testing Kenwood TK-3180K2 detect ... ok test_edges (tests.TestCase_KenwoodTK3180K2) Testing Kenwood TK-3180K2 edges ... ok test_settings (tests.TestCase_KenwoodTK3180K2) Testing Kenwood TK-3180K2 settings ... ok test_banks (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A brute force ... ok test_clone (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A clone ... ok test_copy_all (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A copy all ... ok test_detect (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A detect ... ok test_edges (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A edges ... ok test_settings (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A settings ... ok test_banks (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D banks ... ok test_brute_force (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D brute force ... ok test_clone (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D clone ... ok test_copy_all (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D copy all ... ok test_detect (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D detect ... ok test_edges (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D edges ... ok test_settings (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D settings ... ok test_banks (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R brute force ... ok test_clone (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R clone ... ok test_copy_all (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R copy all ... ok test_detect (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R detect ... ok test_edges (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R edges ... ok test_settings (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R settings ... ok test_banks (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R banks ... ok test_brute_force (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R brute force ... ok test_clone (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R clone ... ok test_copy_all (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R copy all ... ok test_detect (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R detect ... ok test_edges (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R edges ... ok test_settings (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R settings ... ok test_banks (tests.TestCase_QYTKT7900D) Testing QYT KT7900D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_QYTKT7900D) Testing QYT KT7900D brute force ... ok test_clone (tests.TestCase_QYTKT7900D) Testing QYT KT7900D clone ... ok test_copy_all (tests.TestCase_QYTKT7900D) Testing QYT KT7900D copy all ... ok test_detect (tests.TestCase_QYTKT7900D) Testing QYT KT7900D detect ... ok test_edges (tests.TestCase_QYTKT7900D) Testing QYT KT7900D edges ... ok test_settings (tests.TestCase_QYTKT7900D) Testing QYT KT7900D settings ... ok test_banks (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 brute force ... ok test_clone (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 clone ... ok test_copy_all (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 copy all ... ok test_detect (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 detect ... ok test_edges (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 edges ... ok test_settings (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 brute force ... ok test_clone (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 clone ... ok test_copy_all (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 copy all ... ok test_detect (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 detect ... ok test_edges (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 edges ... ok test_settings (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 settings ... ok test_banks (tests.TestCase_IcomICT70) Testing Icom IC-T70 banks ... ok test_brute_force (tests.TestCase_IcomICT70) Testing Icom IC-T70 brute force ... ok test_clone (tests.TestCase_IcomICT70) Testing Icom IC-T70 clone ... ok test_copy_all (tests.TestCase_IcomICT70) Testing Icom IC-T70 copy all ... ok test_detect (tests.TestCase_IcomICT70) Testing Icom IC-T70 detect ... ok test_edges (tests.TestCase_IcomICT70) Testing Icom IC-T70 edges ... ok test_settings (tests.TestCase_IcomICT70) Testing Icom IC-T70 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R brute force ... ok test_clone (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R clone ... ok test_copy_all (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R copy all ... ok test_detect (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R detect ... ok test_edges (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R edges ... ok test_settings (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R settings ... skipped 'Settings not supported' test_banks (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G banks ... ok test_brute_force (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G brute force ... ok test_clone (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G clone ... ok test_copy_all (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G copy all ... ok test_detect (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G detect ... ok test_edges (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G edges ... ok test_settings (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G settings ... ok test_banks (tests.TestCase_CRTMicronUV) Testing CRT Micron UV banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_CRTMicronUV) Testing CRT Micron UV brute force ... ok test_clone (tests.TestCase_CRTMicronUV) Testing CRT Micron UV clone ... ok test_copy_all (tests.TestCase_CRTMicronUV) Testing CRT Micron UV copy all ... ok test_detect (tests.TestCase_CRTMicronUV) Testing CRT Micron UV detect ... ok test_edges (tests.TestCase_CRTMicronUV) Testing CRT Micron UV edges ... ok test_settings (tests.TestCase_CRTMicronUV) Testing CRT Micron UV settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 brute force ... ok test_clone (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 clone ... ok test_copy_all (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 copy all ... ok test_detect (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 detect ... ok test_edges (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 edges ... ok test_settings (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 settings ... ok test_banks (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) brute force ... ok test_clone (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) clone ... ok test_copy_all (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) copy all ... ok test_detect (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) detect ... ok test_edges (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) edges ... ok test_settings (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) settings ... ok test_banks (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 brute force ... ok test_clone (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 clone ... ok test_copy_all (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 copy all ... ok test_detect (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 detect ... ok test_edges (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 edges ... ok test_settings (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 settings ... ok test_banks (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 brute force ... ok test_clone (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 clone ... ok test_copy_all (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 copy all ... ok test_detect (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 detect ... ok test_edges (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 edges ... ok test_settings (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 settings ... ok test_banks (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 banks ... ok test_brute_force (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 brute force ... ok test_clone (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 clone ... ok test_copy_all (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 copy all ... ok test_detect (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 detect ... ok test_edges (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 edges ... ok test_settings (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomICT7H) Testing Icom IC-T7H banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICT7H) Testing Icom IC-T7H brute force ... ok test_clone (tests.TestCase_IcomICT7H) Testing Icom IC-T7H clone ... ok test_copy_all (tests.TestCase_IcomICT7H) Testing Icom IC-T7H copy all ... ok test_detect (tests.TestCase_IcomICT7H) Testing Icom IC-T7H detect ... ok test_edges (tests.TestCase_IcomICT7H) Testing Icom IC-T7H edges ... ok test_settings (tests.TestCase_IcomICT7H) Testing Icom IC-T7H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 brute force ... ok test_clone (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 clone ... ok test_copy_all (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 copy all ... ok test_detect (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 detect ... ok test_edges (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 edges ... ok test_settings (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A brute force ... ok test_clone (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A clone ... ok test_copy_all (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A copy all ... ok test_detect (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A detect ... ok test_edges (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A edges ... ok test_settings (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A settings ... ok test_banks (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 brute force ... ok test_clone (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 clone ... ok test_copy_all (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 copy all ... ok test_detect (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 detect ... ok test_edges (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 edges ... ok test_settings (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 settings ... ok test_banks (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 brute force ... ok test_clone (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 clone ... ok test_copy_all (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 copy all ... ok test_detect (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 detect ... ok test_edges (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 edges ... skipped 'No mutable memory locations found' test_settings (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 settings ... ok test_banks (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R banks ... ok test_brute_force (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R brute force ... ok test_clone (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R clone ... ok test_copy_all (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R copy all ... ok test_detect (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R detect ... ok test_edges (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R edges ... ok test_settings (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R settings ... ok test_banks (tests.TestCase_QYTKT8900D) Testing QYT KT8900D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_QYTKT8900D) Testing QYT KT8900D brute force ... ok test_clone (tests.TestCase_QYTKT8900D) Testing QYT KT8900D clone ... ok test_copy_all (tests.TestCase_QYTKT8900D) Testing QYT KT8900D copy all ... ok test_detect (tests.TestCase_QYTKT8900D) Testing QYT KT8900D detect ... ok test_edges (tests.TestCase_QYTKT8900D) Testing QYT KT8900D edges ... ok test_settings (tests.TestCase_QYTKT8900D) Testing QYT KT8900D settings ... ok test_banks (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B brute force ... ok test_clone (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B clone ... ok test_copy_all (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B copy all ... ok test_detect (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B detect ... ok test_edges (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B edges ... ok test_settings (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B settings ... ok test_banks (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 brute force ... ok test_clone (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 clone ... ok test_copy_all (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 copy all ... ok test_detect (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 detect ... ok test_edges (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 edges ... ok test_settings (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 settings ... ok test_banks (tests.TestCase_IcomICT8A) Testing Icom IC-T8A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICT8A) Testing Icom IC-T8A brute force ... ok test_clone (tests.TestCase_IcomICT8A) Testing Icom IC-T8A clone ... ok test_copy_all (tests.TestCase_IcomICT8A) Testing Icom IC-T8A copy all ... ok test_detect (tests.TestCase_IcomICT8A) Testing Icom IC-T8A detect ... ok test_edges (tests.TestCase_IcomICT8A) Testing Icom IC-T8A edges ... ok test_settings (tests.TestCase_IcomICT8A) Testing Icom IC-T8A settings ... skipped 'Settings not supported' test_banks (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 brute force ... ok test_clone (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 clone ... ok test_copy_all (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 copy all ... ok test_detect (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 detect ... ok test_edges (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 edges ... ok test_settings (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 settings ... ok test_banks (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 banks ... ok test_brute_force (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 brute force ... ok test_clone (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 clone ... ok test_copy_all (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 copy all ... ok test_detect (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 detect ... ok test_edges (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 edges ... ok test_settings (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 brute force ... ok test_clone (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 clone ... ok test_copy_all (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 copy all ... ok test_detect (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 detect ... ok test_edges (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 edges ... ok test_settings (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 settings ... ok test_banks (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M brute force ... ok test_clone (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M clone ... ok test_copy_all (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M copy all ... ok test_detect (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M detect ... ok test_edges (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M edges ... ok test_settings (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode brute force ... ok test_clone (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode clone ... ok test_copy_all (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode copy all ... ok test_detect (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode detect ... ok test_edges (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode edges ... ok test_settings (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode settings ... ok test_banks (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 brute force ... ok test_clone (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 clone ... ok test_copy_all (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 copy all ... ok test_detect (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 detect ... ok test_edges (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 edges ... ok test_settings (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 settings ... ok test_banks (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B brute force ... ok test_clone (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B clone ... ok test_copy_all (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B copy all ... ok test_detect (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B detect ... ok test_edges (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B edges ... ok test_settings (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B settings ... ok test_banks (tests.TestCase_IcomICW32A) Testing Icom IC-W32A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICW32A) Testing Icom IC-W32A brute force ... ok test_clone (tests.TestCase_IcomICW32A) Testing Icom IC-W32A clone ... ok test_copy_all (tests.TestCase_IcomICW32A) Testing Icom IC-W32A copy all ... ok test_detect (tests.TestCase_IcomICW32A) Testing Icom IC-W32A detect ... ok test_edges (tests.TestCase_IcomICW32A) Testing Icom IC-W32A edges ... ok test_settings (tests.TestCase_IcomICW32A) Testing Icom IC-W32A settings ... skipped 'Settings not supported' test_banks (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 brute force ... ok test_clone (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 clone ... ok test_copy_all (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 copy all ... ok test_detect (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 detect ... ok test_edges (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 edges ... ok test_settings (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 settings ... ok test_banks (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode brute force ... ok test_clone (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode clone ... ok test_copy_all (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode copy all ... ok test_detect (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode detect ... ok test_edges (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode edges ... ok test_settings (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode settings ... ok test_banks (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D banks ... ok test_brute_force (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D brute force ... ok test_clone (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D clone ... ok test_copy_all (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D copy all ... ok test_detect (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D detect ... ok test_edges (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D edges ... ok test_settings (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D settings ... ok test_banks (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R banks ... ok test_brute_force (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R brute force ... ok test_clone (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R clone ... ok test_copy_all (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R copy all ... ok test_detect (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R detect ... ok test_edges (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R edges ... ok test_settings (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R settings ... ok test_banks (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 brute force ... ok test_clone (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 clone ... ok test_copy_all (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 copy all ... ok test_detect (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 detect ... ok test_edges (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 edges ... ok test_settings (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomICW32E) Testing Icom IC-W32E banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICW32E) Testing Icom IC-W32E brute force ... ok test_clone (tests.TestCase_IcomICW32E) Testing Icom IC-W32E clone ... ok test_copy_all (tests.TestCase_IcomICW32E) Testing Icom IC-W32E copy all ... ok test_detect (tests.TestCase_IcomICW32E) Testing Icom IC-W32E detect ... ok test_edges (tests.TestCase_IcomICW32E) Testing Icom IC-W32E edges ... ok test_settings (tests.TestCase_IcomICW32E) Testing Icom IC-W32E settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 brute force ... ok test_clone (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 clone ... ok test_copy_all (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 copy all ... ok test_detect (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 detect ... ok test_edges (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 edges ... ok test_settings (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 settings ... ok test_banks (tests.TestCase_RadioddityR2) Testing Radioddity R2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RadioddityR2) Testing Radioddity R2 brute force ... ok test_clone (tests.TestCase_RadioddityR2) Testing Radioddity R2 clone ... ok test_copy_all (tests.TestCase_RadioddityR2) Testing Radioddity R2 copy all ... ok test_detect (tests.TestCase_RadioddityR2) Testing Radioddity R2 detect ... ok test_edges (tests.TestCase_RadioddityR2) Testing Radioddity R2 edges ... ok test_settings (tests.TestCase_RadioddityR2) Testing Radioddity R2 settings ... ok test_banks (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D brute force ... ok test_clone (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D clone ... ok test_copy_all (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D copy all ... ok test_detect (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D detect ... ok test_edges (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D edges ... ok test_settings (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D settings ... ok test_banks (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode brute force ... ok test_clone (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode clone ... ok test_copy_all (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode copy all ... ok test_detect (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode detect ... ok test_edges (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode edges ... ok test_settings (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode settings ... ok test_banks (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 brute force ... ok test_clone (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 clone ... ok test_copy_all (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 copy all ... ok test_detect (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 detect ... ok test_edges (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 edges ... ok test_settings (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 settings ... ok test_banks (tests.TestCase_IcomIC208H) Testing Icom IC-208H banks ... ok test_brute_force (tests.TestCase_IcomIC208H) Testing Icom IC-208H brute force ... ok test_clone (tests.TestCase_IcomIC208H) Testing Icom IC-208H clone ... ok test_copy_all (tests.TestCase_IcomIC208H) Testing Icom IC-208H copy all ... ok test_detect (tests.TestCase_IcomIC208H) Testing Icom IC-208H detect ... ok test_edges (tests.TestCase_IcomIC208H) Testing Icom IC-208H edges ... ok test_settings (tests.TestCase_IcomIC208H) Testing Icom IC-208H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_RadtelT18) Testing Radtel T18 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RadtelT18) Testing Radtel T18 brute force ... ok test_clone (tests.TestCase_RadtelT18) Testing Radtel T18 clone ... ok test_copy_all (tests.TestCase_RadtelT18) Testing Radtel T18 copy all ... ok test_detect (tests.TestCase_RadtelT18) Testing Radtel T18 detect ... ok test_edges (tests.TestCase_RadtelT18) Testing Radtel T18 edges ... ok test_settings (tests.TestCase_RadtelT18) Testing Radtel T18 settings ... ok test_banks (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 brute force ... ok test_clone (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 clone ... ok test_copy_all (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 copy all ... ok test_detect (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 detect ... ok test_edges (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 edges ... ok test_settings (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 settings ... ok test_banks (tests.TestCase_IcomID31A) Testing Icom ID-31A banks ... ok test_brute_force (tests.TestCase_IcomID31A) Testing Icom ID-31A brute force ... ok test_clone (tests.TestCase_IcomID31A) Testing Icom ID-31A clone ... ok test_copy_all (tests.TestCase_IcomID31A) Testing Icom ID-31A copy all ... ok test_detect (tests.TestCase_IcomID31A) Testing Icom ID-31A detect ... ok test_edges (tests.TestCase_IcomID31A) Testing Icom ID-31A edges ... ok test_settings (tests.TestCase_IcomID31A) Testing Icom ID-31A settings ... ok test_banks (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode brute force ... ok test_clone (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode clone ... ok test_copy_all (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode copy all ... ok test_detect (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode detect ... ok test_edges (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode edges ... ok test_settings (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode settings ... ok test_banks (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR banks ... ok test_brute_force (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR brute force ... ok test_clone (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR clone ... ok test_copy_all (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR copy all ... ok test_detect (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR detect ... ok test_edges (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR edges ... ok test_settings (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR settings ... ok test_banks (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D banks ... ok test_brute_force (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D brute force ... ok test_clone (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D clone ... ok test_copy_all (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D copy all ... ok test_detect (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D detect ... ok test_edges (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D edges ... ok test_settings (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D settings ... ok test_banks (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H brute force ... ok test_clone (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H clone ... ok test_copy_all (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H copy all ... ok test_detect (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H detect ... ok test_edges (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H edges ... ok test_settings (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 brute force ... ok test_clone (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 clone ... ok test_copy_all (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 copy all ... ok test_detect (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 detect ... ok test_edges (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 edges ... ok test_settings (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 settings ... ok test_banks (tests.TestCase_RetevisRT21) Testing Retevis RT21 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT21) Testing Retevis RT21 brute force ... ok test_clone (tests.TestCase_RetevisRT21) Testing Retevis RT21 clone ... ok test_copy_all (tests.TestCase_RetevisRT21) Testing Retevis RT21 copy all ... ok test_detect (tests.TestCase_RetevisRT21) Testing Retevis RT21 detect ... ok test_edges (tests.TestCase_RetevisRT21) Testing Retevis RT21 edges ... ok test_settings (tests.TestCase_RetevisRT21) Testing Retevis RT21 settings ... ok test_banks (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV brute force ... ok test_clone (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV clone ... ok test_copy_all (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV copy all ... ok test_detect (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV detect ... ok test_edges (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV edges ... ok test_settings (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV settings ... ok test_banks (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE banks ... ok test_brute_force (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE brute force ... ok test_clone (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE clone ... ok test_copy_all (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE copy all ... ok test_detect (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE detect ... ok test_edges (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE edges ... ok test_settings (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE settings ... ok test_banks (tests.TestCase_RetevisRT22) Testing Retevis RT22 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT22) Testing Retevis RT22 brute force ... ok test_clone (tests.TestCase_RetevisRT22) Testing Retevis RT22 clone ... ok test_copy_all (tests.TestCase_RetevisRT22) Testing Retevis RT22 copy all ... ok test_detect (tests.TestCase_RetevisRT22) Testing Retevis RT22 detect ... ok test_edges (tests.TestCase_RetevisRT22) Testing Retevis RT22 edges ... ok test_settings (tests.TestCase_RetevisRT22) Testing Retevis RT22 settings ... ok test_banks (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 brute force ... ok test_clone (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 clone ... ok test_copy_all (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 copy all ... ok test_detect (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 detect ... ok test_edges (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 edges ... ok test_settings (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 settings ... ok test_banks (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D brute force ... ok test_clone (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D clone ... ok test_copy_all (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D copy all ... ok test_detect (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D detect ... ok test_edges (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D edges ... ok test_settings (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR banks ... ok test_brute_force (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR brute force ... ok test_clone (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR clone ... ok test_copy_all (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR copy all ... ok test_detect (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR detect ... ok test_edges (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR edges ... ok test_settings (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR settings ... ok test_banks (tests.TestCase_RetevisRT23) Testing Retevis RT23 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT23) Testing Retevis RT23 brute force ... ok test_clone (tests.TestCase_RetevisRT23) Testing Retevis RT23 clone ... ok test_copy_all (tests.TestCase_RetevisRT23) Testing Retevis RT23 copy all ... ok test_detect (tests.TestCase_RetevisRT23) Testing Retevis RT23 detect ... ok test_edges (tests.TestCase_RetevisRT23) Testing Retevis RT23 edges ... ok test_settings (tests.TestCase_RetevisRT23) Testing Retevis RT23 settings ... ok test_banks (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 brute force ... ok test_clone (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 clone ... ok test_copy_all (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 copy all ... ok test_detect (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 detect ... ok test_edges (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 edges ... ok test_settings (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 settings ... ok test_banks (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 brute force ... ok test_clone (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 clone ... ok test_copy_all (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 copy all ... ok test_detect (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 detect ... ok test_edges (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 edges ... ok test_settings (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 settings ... ok test_banks (tests.TestCase_IcomID51) Testing Icom ID-51 banks ... ok test_brute_force (tests.TestCase_IcomID51) Testing Icom ID-51 brute force ... ok test_clone (tests.TestCase_IcomID51) Testing Icom ID-51 clone ... ok test_copy_all (tests.TestCase_IcomID51) Testing Icom ID-51 copy all ... ok test_detect (tests.TestCase_IcomID51) Testing Icom ID-51 detect ... ok test_edges (tests.TestCase_IcomID51) Testing Icom ID-51 edges ... ok test_settings (tests.TestCase_IcomID51) Testing Icom ID-51 settings ... ok test_banks (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 brute force ... ok test_clone (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 clone ... ok test_copy_all (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 copy all ... ok test_detect (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 detect ... ok test_edges (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 edges ... ok test_settings (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 settings ... ok test_banks (tests.TestCase_RetevisRT26) Testing Retevis RT26 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT26) Testing Retevis RT26 brute force ... ok test_clone (tests.TestCase_RetevisRT26) Testing Retevis RT26 clone ... ok test_copy_all (tests.TestCase_RetevisRT26) Testing Retevis RT26 copy all ... ok test_detect (tests.TestCase_RetevisRT26) Testing Retevis RT26 detect ... ok test_edges (tests.TestCase_RetevisRT26) Testing Retevis RT26 edges ... ok test_settings (tests.TestCase_RetevisRT26) Testing Retevis RT26 settings ... ok test_banks (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D brute force ... ok test_clone (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D clone ... ok test_copy_all (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D copy all ... ok test_detect (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D detect ... ok test_edges (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D edges ... ok test_settings (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D settings ... ok test_banks (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 brute force ... ok test_clone (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 clone ... ok test_copy_all (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 copy all ... ok test_detect (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 detect ... ok test_edges (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 edges ... ok test_settings (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 banks ... ok test_brute_force (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 brute force ... ok test_clone (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 clone ... ok test_copy_all (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 copy all ... ok test_detect (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 detect ... ok test_edges (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 edges ... ok test_settings (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 settings ... ok test_banks (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 brute force ... ok test_clone (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 clone ... ok test_copy_all (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 copy all ... ok test_detect (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 detect ... ok test_edges (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 edges ... ok test_settings (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 settings ... ok test_banks (tests.TestCase_YaesuFT65E) Testing Yaesu FT-65E banks ... ok test_brute_force (tests.TestCase_YaesuFT65E) Testing Yaesu FT-65E brute force ... ok test_clone (tests.TestCase_YaesuFT65E) Testing Yaesu FT-65E clone ... ok test_copy_all (tests.TestCase_YaesuFT65E) Testing Yaesu FT-65E copy all ... ok test_detect (tests.TestCase_YaesuFT65E) Testing Yaesu FT-65E detect ... ok test_edges (tests.TestCase_YaesuFT65E) Testing Yaesu FT-65E edges ... ok test_settings (tests.TestCase_YaesuFT65E) Testing Yaesu FT-65E settings ... ok test_banks (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 brute force ... ok test_clone (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 clone ... ok test_copy_all (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 copy all ... ok test_detect (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 detect ... ok test_edges (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 edges ... ok test_settings (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 settings ... ok test_banks (tests.TestCase_YaesuFTM7250D) Testing Yaesu FTM-7250D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFTM7250D) Testing Yaesu FTM-7250D brute force ... ok test_clone (tests.TestCase_YaesuFTM7250D) Testing Yaesu FTM-7250D clone ... ok test_copy_all (tests.TestCase_YaesuFTM7250D) Testing Yaesu FTM-7250D copy all ... ok test_detect (tests.TestCase_YaesuFTM7250D) Testing Yaesu FTM-7250D detect ... ok test_edges (tests.TestCase_YaesuFTM7250D) Testing Yaesu FTM-7250D edges ... ok test_settings (tests.TestCase_YaesuFTM7250D) Testing Yaesu FTM-7250D settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus banks ... ok test_brute_force (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus brute force ... ok test_clone (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus clone ... ok test_copy_all (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus copy all ... ok test_detect (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus detect ... ok test_edges (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus edges ... ok test_settings (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus settings ... ok test_banks (tests.TestCase_IcomID800H) Testing Icom ID-800H banks ... ok test_brute_force (tests.TestCase_IcomID800H) Testing Icom ID-800H brute force ... ok test_clone (tests.TestCase_IcomID800H) Testing Icom ID-800H clone ... ok test_copy_all (tests.TestCase_IcomID800H) Testing Icom ID-800H copy all ... ok test_detect (tests.TestCase_IcomID800H) Testing Icom ID-800H detect ... ok test_edges (tests.TestCase_IcomID800H) Testing Icom ID-800H edges ... ok test_settings (tests.TestCase_IcomID800H) Testing Icom ID-800H settings ... ok ---------------------------------------------------------------------- Ran 1001 tests in 405.747s OK (skipped=141) struct memory { bbcd rx_freq[4]; bbcd tx_freq[4]; lbcd rx_tone[2]; lbcd tx_tone[2]; u8 unknown10:5, highpower:1, unknown11:2; u8 unknown20:4, narrow:1, unknown21:3; u8 unknown31:1, scanadd:1, unknown32:6; u8 unknown4; }; struct name { char name[7]; }; #seekto 0x0010; struct memory channels[128]; #seekto 0x08C0; struct name names[128]; #seekto 0x2020; struct memory vfo1; struct memory vfo2; style create: /chirp/.tox/style style installdeps: pep8==1.6.2, future style inst: /chirp/.tox/.tmp/package/1/chirp-0.3.0dev.zip style installed: DEPRECATION: Python 2.7 will reach the end of its life on January 1st, 2020. Please upgrade your Python as Python 2.7 won't be maintained after that date. A future version of pip will drop support for Python 2.7.,chirp==0.3.0.dev0,configparser==3.7.4,contextlib2==0.5.5,filelock==3.0.12,future==0.15.2,importlib-metadata==0.18,Mako==1.0.3,MarkupSafe==0.23,mercurial==3.7.3,packaging==19.0,pathlib2==2.3.4,pep8==1.6.2,pluggy==0.12.0,py==1.8.0,pygobject==3.20.0,pyparsing==2.4.0,pyserial==3.0.1,scandir==1.10.0,six==1.12.0,toml==0.10.0,tox==3.13.2,virtualenv==16.6.1,zipp==0.5.2 style run-test-pre: PYTHONHASHSEED='1117807279' style run-test: commands[0] | python ./tools/cpep8.py ___________________________________ summary ____________________________________ unit: commands succeeded driver: commands succeeded style: commands succeeded congratulations :) Email was triggered for: Success Sending email for trigger: Success

1 0

[chirp_devel] Getting (Re)started
by Joseph.P.Scanlan＠n7xsd.us 06 Sep '20

06 Sep '20

The last few years have been a little… distracting but I’m anxious to get back to chirp. I did some work on the Icom IC-7000 driver in the past. So: How do I install python-libxslt1, python-gtk2, python-serial, and python-suds on Ubuntu Focal? Should I be looking at the Python 3 branch instead? — Joseph.P.Scanlan(a)n7xsd.us — n7xsd(a)arrl.net — +1-702-896-0507

2 2

[chirp_devel] Anytone AT-D878UV support
by Kosmas Raptis 06 Sep '20

06 Sep '20

Hello! Thank you for informing me about this, I will definitely use this method when trying to make a driver for any future radios (I would in this one, too, but as Mr. Jim said, CHIRP doesn't support Digital radios. Or is Mr. Jim wrong?). For now I'll see what I can help with in existing CHIRP code. Again, thank you! Kosmas SY1DKC

2 1

[chirp_devel] AnyTone AT-D878UV support
by Kosmas Raptis 05 Sep '20

05 Sep '20

Hello! I've been using CHIRP for a while to program my QYT KT8900D, and recently I became interested in adding support for my handheld radio, the AnyTone AT-D878UV PLUS (and, by extent, the regular version of it). I set up a dev environment on Ubuntu 20.04, used USBPcap to capture its packet data from a Read using its official CPS from Windows, as the Add a Radio guide suggests, and got that to Ubuntu to analyze with WireShark to start working on the driver. I managed to figure out that it has a baud rate of 9600, and which device it is from the .pcap file, also saw that it does a lot of URB_BULK in and out requests, and also figured out there are actually 2 devices in address 1.2 (where my radio is), 1.2.1 and 1.2.3. The communication works like this, if my order is correct: host to 1.2.1: URB_BULK in, packet data length is 0 host to 1.2.3: URB_BULK out, packet data length is 6 1.2.3 to host: URB_BULK out, packet data length is 0 1.2.1 to host: URB_BULK in, packet data length is 24 Repeat multiple times (my radio has a lot of entries on it. Is it recommended that I try with 1 entry on it, maybe, to get a shorter pcap file that also shows me how it's done per entry? Or doesn't it matter?) But I also need some help. How can I figure out the memory map? How do I see the actual data sent in the packet and not just its header? How do I check how the radio returns stuff like the version? Also, what are these URB_BULK requests? Does it mean that it just dumps its memory without some specific protocol? I really need help here, I'm very new to this (Haven't worked on this for more than a couple hours, actually, and this is my first time reverse engineering anything and using WireShark or USBPcap, and I have a lot of questions). Thank you for your help!

3 3

[chirp_devel] Build test results: Successful
by Build System 01 Sep '20

01 Sep '20

Tested changes: Changes for Build #885 [Jim Unroe <rock.unroe(a)gmail.com>] [UV-6] Support Baofeng UV-6 without Auxiliary Block This patch adds support for Baofeng radio models, including the UV-6, that do not support access to the auxiliary block of memory. Fixes #6567 [Tom Hayward <tom(a)tomh.us>] [id880] Fix typo in charset definition. #281 [Tom Hayward <tom(a)tomh.us>] [thf6a] Support full charset (ASCII). Fixes #141 [Tom Hayward <tom(a)tomh.us>] [id880] Support full charset. Fixes #281 [Tom Hayward <tom(a)tomh.us>] [vx5] Support full charset (ASCII). Fixes #292 [Tom Hayward <tom(a)tomh.us>] [id31a] set used bit when creating new memory, clear when deleting. Fixes #269 [Tom Hayward <tom(a)tomh.us>] Support PyGTK < 2.22 in bank edit. Fixes #231 [Tom Hayward <tom(a)tomh.us>] [d710] [v71] [d72] Fix tone list (not all tones are supported). Fixes #212 [Dan Smith <dsmith(a)danplanet.com>] [vx7] Fix setting memory power levels on 220MHz band Fixes #214 [Dan Smith <dsmith(a)danplanet.com>] fips: Pennsylvania FIPS code was wrong. #117 [Marco Filippi <iz3gme.marco(a)gmail.com>] Consider lower bound frequency of each valid_band as valid Fix bug #181 [Tom Hayward <tom(a)tomh.us>] tmd700: allow 8-char names. Fixes #176 [Dan Smith <dsmith(a)danplanet.com>] Fix the "blind deletion" problem, as well as properly direct copy/paste Fixes #172 [David Griffith <dave(a)661.org>] Bug #155 fix: VX-7 1.25m power levels [David Griffith <dave(a)661.org>] New INSTALL and README files Fixes #122 [Tom Hayward <tom(a)tomh.us>] thd72: only use hardware flow on OS X. Fixes #166 [Marco Filippi <iz3gme.marco(a)gmail.com>] [FT817] Tone freq not set correctly Same as #88 for FT857, to avoid code duplication fix code have been moved from ft857 to its ancestor class Fix bug #163 [Tom Hayward <tom(a)tomh.us>] Fix Mac .app so paths with spaces work. Fixes Bug #145 Full log: [...truncated 672 lines...] test_copy_all (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 copy all ... ok test_detect (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 detect ... ok test_edges (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 edges ... ok test_settings (tests.TestCase_YaesuVX6) Testing Yaesu VX-6 settings ... ok test_banks (tests.TestCase_TYTTH9800) Testing TYT TH-9800 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTH9800) Testing TYT TH-9800 brute force ... ok test_clone (tests.TestCase_TYTTH9800) Testing TYT TH-9800 clone ... ok test_copy_all (tests.TestCase_TYTTH9800) Testing TYT TH-9800 copy all ... ok test_detect (tests.TestCase_TYTTH9800) Testing TYT TH-9800 detect ... ok test_edges (tests.TestCase_TYTTH9800) Testing TYT TH-9800 edges ... ok test_settings (tests.TestCase_TYTTH9800) Testing TYT TH-9800 settings ... ok test_banks (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R brute force ... ok test_clone (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R clone ... ok test_copy_all (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R copy all ... ok test_detect (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R detect ... ok test_edges (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R edges ... ok test_settings (tests.TestCase_AnyToneOBLTR8R) Testing AnyTone OBLTR-8R settings ... ok test_banks (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H banks ... ok test_brute_force (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H brute force ... ok test_clone (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H clone ... ok test_copy_all (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H copy all ... ok test_detect (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H detect ... ok test_edges (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H edges ... ok test_settings (tests.TestCase_IcomIC2300H) Testing Icom IC-2300H settings ... ok test_banks (tests.TestCase_BaofengF11) Testing Baofeng F-11 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengF11) Testing Baofeng F-11 brute force ... ok test_clone (tests.TestCase_BaofengF11) Testing Baofeng F-11 clone ... ok test_copy_all (tests.TestCase_BaofengF11) Testing Baofeng F-11 copy all ... ok test_detect (tests.TestCase_BaofengF11) Testing Baofeng F-11 detect ... ok test_edges (tests.TestCase_BaofengF11) Testing Baofeng F-11 edges ... ok test_settings (tests.TestCase_BaofengF11) Testing Baofeng F-11 settings ... ok test_banks (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 brute force ... ok test_clone (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 clone ... ok test_copy_all (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 copy all ... ok test_detect (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 detect ... ok test_edges (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 edges ... ok test_settings (tests.TestCase_YaesuFT818) Testing Yaesu FT-818 settings ... ok test_banks (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M brute force ... ok test_clone (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M clone ... ok test_copy_all (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M copy all ... ok test_detect (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M detect ... ok test_edges (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M edges ... ok test_settings (tests.TestCase_JetstreamJT270M) Testing Jetstream JT270M settings ... ok test_banks (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 brute force ... ok test_clone (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 clone ... ok test_copy_all (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 copy all ... ok test_detect (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 detect ... ok test_edges (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 edges ... ok test_settings (tests.TestCase_TYTTHUV3R25) Testing TYT TH-UV3R-25 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 banks ... ok test_brute_force (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 brute force ... ok test_clone (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 clone ... ok test_copy_all (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 copy all ... ok test_detect (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 detect ... ok test_edges (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 edges ... ok test_settings (tests.TestCase_YaesuVX7) Testing Yaesu VX-7 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 brute force ... ok test_clone (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 clone ... ok test_copy_all (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 copy all ... ok test_detect (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 detect ... ok test_edges (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 edges ... ok test_settings (tests.TestCase_YaesuFT857897) Testing Yaesu FT-857/897 settings ... ok test_banks (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus brute force ... ok test_clone (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus clone ... ok test_copy_all (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus copy all ... ok test_detect (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus detect ... ok test_edges (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus edges ... ok test_settings (tests.TestCase_WouxunKGUV9DPlus) Testing Wouxun KG-UV9D Plus settings ... ok test_banks (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R brute force ... ok test_clone (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R clone ... ok test_copy_all (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R copy all ... ok test_detect (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R detect ... ok test_edges (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R edges ... ok test_settings (tests.TestCase_TYTTHUV3R) Testing TYT TH-UV3R settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) brute force ... ok test_clone (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) clone ... ok test_copy_all (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) copy all ... ok test_detect (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) detect ... ok test_edges (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) edges ... ok test_settings (tests.TestCase_YaesuFT857897US) Testing Yaesu FT-857/897 (US) settings ... ok test_banks (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR banks ... ok test_brute_force (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR brute force ... ok test_clone (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR clone ... ok test_copy_all (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR copy all ... ok test_detect (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR detect ... ok test_edges (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR edges ... ok test_settings (tests.TestCase_YaesuVX8DR) Testing Yaesu VX-8DR settings ... ok test_banks (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H banks ... ok test_brute_force (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H brute force ... ok test_clone (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H clone ... ok test_copy_all (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H copy all ... ok test_detect (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H detect ... ok test_edges (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H edges ... ok test_settings (tests.TestCase_IcomIC2720H) Testing Icom IC-2720H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R brute force ... ok test_clone (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R clone ... ok test_copy_all (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R copy all ... ok test_detect (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R detect ... ok test_edges (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R edges ... ok test_settings (tests.TestCase_AnyToneTERMN8R) Testing AnyTone TERMN-8R settings ... ok test_banks (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH brute force ... ok test_clone (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH clone ... ok test_copy_all (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH copy all ... ok test_detect (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH detect ... ok test_edges (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH edges ... ok test_settings (tests.TestCase_JetstreamJT270MH) Testing Jetstream JT270MH settings ... ok test_banks (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P brute force ... ok test_clone (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P clone ... ok test_copy_all (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P copy all ... ok test_detect (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P detect ... ok test_edges (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P edges ... ok test_settings (tests.TestCase_WouxunKGUVD1P) Testing Wouxun KG-UVD1P settings ... ok test_banks (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 banks ... ok test_brute_force (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 brute force ... ok test_clone (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 clone ... ok test_copy_all (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 copy all ... ok test_detect (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 detect ... ok test_edges (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 edges ... ok test_settings (tests.TestCase_YaesuFT8800) Testing Yaesu FT-8800 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R brute force ... ok test_clone (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R clone ... ok test_copy_all (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R copy all ... ok test_detect (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R detect ... ok test_edges (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R edges ... ok test_settings (tests.TestCase_BaofengUV3R) Testing Baofeng UV-3R settings ... ok test_banks (tests.TestCase_KYDIP620) Testing KYD IP-620 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KYDIP620) Testing KYD IP-620 brute force ... ok test_clone (tests.TestCase_KYDIP620) Testing KYD IP-620 clone ... ok test_copy_all (tests.TestCase_KYDIP620) Testing KYD IP-620 copy all ... ok test_detect (tests.TestCase_KYDIP620) Testing KYD IP-620 detect ... ok test_edges (tests.TestCase_KYDIP620) Testing KYD IP-620 edges ... ok test_settings (tests.TestCase_KYDIP620) Testing KYD IP-620 settings ... ok test_banks (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A banks ... ok test_brute_force (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A brute force ... ok test_clone (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A clone ... ok test_copy_all (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A copy all ... ok test_detect (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A detect ... ok test_edges (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A edges ... ok test_settings (tests.TestCase_IcomIC2730A) Testing Icom IC-2730A settings ... ok test_banks (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 brute force ... ok test_clone (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 clone ... ok test_copy_all (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 copy all ... ok test_detect (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 detect ... ok test_edges (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 edges ... ok test_settings (tests.TestCase_TYTTHUV8000) Testing TYT TH-UV8000 settings ... ok test_banks (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R brute force ... ok test_clone (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R clone ... ok test_copy_all (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R copy all ... ok test_detect (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R detect ... ok test_edges (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R edges ... ok test_settings (tests.TestCase_BaofengUV5R) Testing Baofeng UV-5R settings ... ok test_banks (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M brute force ... ok test_clone (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M clone ... ok test_copy_all (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M copy all ... ok test_detect (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M detect ... ok test_edges (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M edges ... ok test_settings (tests.TestCase_YaesuFT1500M) Testing Yaesu FT-1500M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 brute force ... ok test_clone (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 clone ... ok test_copy_all (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 copy all ... ok test_detect (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 detect ... ok test_edges (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 edges ... ok test_settings (tests.TestCase_BTECHGMRS50X1) Testing BTECH GMRS-50X1 settings ... ok test_banks (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE banks ... ok test_brute_force (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE brute force ... ok test_clone (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE clone ... ok test_copy_all (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE copy all ... ok test_detect (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE detect ... ok test_edges (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE edges ... ok test_settings (tests.TestCase_YaesuVX8GE) Testing Yaesu VX-8GE settings ... ok test_banks (tests.TestCase_KYDNC630A) Testing KYD NC-630A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KYDNC630A) Testing KYD NC-630A brute force ... ok test_clone (tests.TestCase_KYDNC630A) Testing KYD NC-630A clone ... ok test_copy_all (tests.TestCase_KYDNC630A) Testing KYD NC-630A copy all ... ok test_detect (tests.TestCase_KYDNC630A) Testing KYD NC-630A detect ... ok test_edges (tests.TestCase_KYDNC630A) Testing KYD NC-630A edges ... ok test_settings (tests.TestCase_KYDNC630A) Testing KYD NC-630A settings ... ok test_banks (tests.TestCase_MidlandDBR2500) Testing Midland DBR2500 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_MidlandDBR2500) Testing Midland DBR2500 brute force ... ok test_clone (tests.TestCase_MidlandDBR2500) Testing Midland DBR2500 clone ... ok test_copy_all (tests.TestCase_MidlandDBR2500) Testing Midland DBR2500 copy all ... ok test_detect (tests.TestCase_MidlandDBR2500) Testing Midland DBR2500 detect ... ok test_edges (tests.TestCase_MidlandDBR2500) Testing Midland DBR2500 edges ... ok test_settings (tests.TestCase_MidlandDBR2500) Testing Midland DBR2500 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 brute force ... ok test_clone (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 clone ... ok test_copy_all (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 copy all ... ok test_detect (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 detect ... ok test_edges (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 edges ... ok test_settings (tests.TestCase_BTECHGMRSV1) Testing BTECH GMRS-V1 settings ... ok test_banks (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R banks ... ok test_brute_force (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R brute force ... ok test_clone (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R clone ... ok test_copy_all (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R copy all ... ok test_detect (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R detect ... ok test_edges (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R edges ... ok test_settings (tests.TestCase_YaesuVX8R) Testing Yaesu VX-8R settings ... ok test_banks (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 brute force ... ok test_clone (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 clone ... ok test_copy_all (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 copy all ... ok test_detect (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 detect ... ok test_edges (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 edges ... ok test_settings (tests.TestCase_YaesuFT8900) Testing Yaesu FT-8900 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M brute force ... ok test_clone (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M clone ... ok test_copy_all (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M copy all ... ok test_detect (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M detect ... ok test_edges (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M edges ... ok test_settings (tests.TestCase_YaesuFT1802M) Testing Yaesu FT-1802M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R brute force ... ok test_clone (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R clone ... ok test_copy_all (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R copy all ... ok test_detect (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R detect ... ok test_edges (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R edges ... ok test_settings (tests.TestCase_BaofengUV6R) Testing Baofeng UV-6R settings ... ok test_banks (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) brute force ... ok test_clone (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) clone ... ok test_copy_all (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) copy all ... ok test_detect (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) detect ... ok test_edges (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) edges ... ok test_settings (tests.TestCase_KenwoodTHD72clonemode) Testing Kenwood TH-D72 (clone mode) settings ... ok test_banks (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H banks ... ok test_brute_force (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H brute force ... ok test_clone (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H clone ... ok test_copy_all (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H copy all ... ok test_detect (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H detect ... ok test_edges (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H edges ... ok test_settings (tests.TestCase_IcomIC2820H) Testing Icom IC-2820H settings ... ok test_banks (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 brute force ... ok test_clone (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 clone ... ok test_copy_all (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 copy all ... ok test_detect (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 detect ... ok test_edges (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 edges ... skipped 'No mutable memory locations found' test_settings (tests.TestCase_BTECHMURSV1) Testing BTECH MURS-V1 settings ... ok test_banks (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 brute force ... ok test_clone (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 clone ... ok test_copy_all (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 copy all ... ok test_detect (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 detect ... ok test_edges (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 edges ... ok test_settings (tests.TestCase_TYTTHUVF1) Testing TYT TH-UVF1 settings ... ok test_banks (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 brute force ... ok test_clone (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 clone ... ok test_copy_all (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 copy all ... ok test_detect (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 detect ... ok test_edges (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 edges ... ok test_settings (tests.TestCase_BaofengUVB5) Testing Baofeng UV-B5 settings ... ok test_banks (tests.TestCase_IcomICP7) Testing Icom IC-P7 banks ... ok test_brute_force (tests.TestCase_IcomICP7) Testing Icom IC-P7 brute force ... ok test_clone (tests.TestCase_IcomICP7) Testing Icom IC-P7 clone ... ok test_copy_all (tests.TestCase_IcomICP7) Testing Icom IC-P7 copy all ... ok test_detect (tests.TestCase_IcomICP7) Testing Icom IC-P7 detect ... ok test_edges (tests.TestCase_IcomICP7) Testing Icom IC-P7 edges ... ok test_settings (tests.TestCase_IcomICP7) Testing Icom IC-P7 settings ... ok test_banks (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D banks ... ok test_brute_force (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D brute force ... ok test_clone (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D clone ... ok test_copy_all (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D copy all ... ok test_detect (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D detect ... ok test_edges (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D edges ... ok test_settings (tests.TestCase_YaesuFT2D) Testing Yaesu FT2D settings ... ok test_banks (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M brute force ... ok test_clone (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M clone ... ok test_copy_all (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M copy all ... ok test_detect (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M detect ... ok test_edges (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M edges ... ok test_settings (tests.TestCase_PolmarDB50M) Testing Polmar DB-50M settings ... ok test_banks (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 brute force ... ok test_clone (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 clone ... ok test_copy_all (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 copy all ... ok test_detect (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 detect ... ok test_edges (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 edges ... ok test_settings (tests.TestCase_BTECHUV2501220) Testing BTECH UV-2501+220 settings ... ok test_banks (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G banks ... ok test_brute_force (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G brute force ... ok test_clone (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G clone ... ok test_copy_all (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G copy all ... ok test_detect (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G detect ... ok test_edges (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G edges ... ok test_settings (tests.TestCase_KenwoodTK272G) Testing Kenwood TK-272G settings ... ok test_banks (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A brute force ... ok test_clone (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A clone ... ok test_copy_all (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A copy all ... ok test_detect (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A detect ... ok test_edges (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A edges ... ok test_settings (tests.TestCase_IcomICQ7A) Testing Icom IC-Q7A settings ... ok test_banks (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D banks ... ok test_brute_force (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D brute force ... ok test_clone (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D clone ... ok test_copy_all (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D copy all ... ok test_detect (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D detect ... ok test_edges (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D edges ... ok test_settings (tests.TestCase_YaesuFT1D) Testing Yaesu FT-1D settings ... ok test_banks (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 brute force ... ok test_clone (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 clone ... ok test_copy_all (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 copy all ... ok test_detect (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 detect ... ok test_edges (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 edges ... ok test_settings (tests.TestCase_TYTTH9000144) Testing TYT TH9000_144 settings ... ok test_banks (tests.TestCase_KenwoodTK3180K2) Testing Kenwood TK-3180K2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTK3180K2) Testing Kenwood TK-3180K2 brute force ... ok test_clone (tests.TestCase_KenwoodTK3180K2) Testing Kenwood TK-3180K2 clone ... ok test_copy_all (tests.TestCase_KenwoodTK3180K2) Testing Kenwood TK-3180K2 copy all ... ok test_detect (tests.TestCase_KenwoodTK3180K2) Testing Kenwood TK-3180K2 detect ... ok test_edges (tests.TestCase_KenwoodTK3180K2) Testing Kenwood TK-3180K2 edges ... ok test_settings (tests.TestCase_KenwoodTK3180K2) Testing Kenwood TK-3180K2 settings ... ok test_banks (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 brute force ... ok test_clone (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 clone ... ok test_copy_all (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 copy all ... ok test_detect (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 detect ... ok test_edges (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 edges ... ok test_settings (tests.TestCase_BaojieBJ9900) Testing Baojie BJ-9900 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D banks ... ok test_brute_force (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D brute force ... ok test_clone (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D clone ... ok test_copy_all (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D copy all ... ok test_detect (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D detect ... ok test_edges (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D edges ... ok test_settings (tests.TestCase_YaesuFT3D) Testing Yaesu FT3D settings ... ok test_banks (tests.TestCase_IcomICT70) Testing Icom IC-T70 banks ... ok test_brute_force (tests.TestCase_IcomICT70) Testing Icom IC-T70 brute force ... ok test_clone (tests.TestCase_IcomICT70) Testing Icom IC-T70 clone ... ok test_copy_all (tests.TestCase_IcomICT70) Testing Icom IC-T70 copy all ... ok test_detect (tests.TestCase_IcomICT70) Testing Icom IC-T70 detect ... ok test_edges (tests.TestCase_IcomICT70) Testing Icom IC-T70 edges ... ok test_settings (tests.TestCase_IcomICT70) Testing Icom IC-T70 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R brute force ... ok test_clone (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R clone ... ok test_copy_all (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R copy all ... ok test_detect (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R detect ... ok test_edges (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R edges ... ok test_settings (tests.TestCase_PuxingPX2R) Testing Puxing PX-2R settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R banks ... ok test_brute_force (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R brute force ... ok test_clone (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R clone ... ok test_copy_all (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R copy all ... ok test_detect (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R detect ... ok test_edges (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R edges ... ok test_settings (tests.TestCase_YaesuFT25R) Testing Yaesu FT-25R settings ... ok test_banks (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M brute force ... ok test_clone (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M clone ... ok test_copy_all (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M copy all ... ok test_detect (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M detect ... ok test_edges (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M edges ... ok test_settings (tests.TestCase_YaesuFT2800M) Testing Yaesu FT-2800M settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D brute force ... ok test_clone (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D clone ... ok test_copy_all (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D copy all ... ok test_detect (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D detect ... ok test_edges (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D edges ... ok test_settings (tests.TestCase_YaesuFTM3200D) Testing Yaesu FTM-3200D settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R banks ... ok test_brute_force (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R brute force ... ok test_clone (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R clone ... ok test_copy_all (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R copy all ... ok test_detect (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R detect ... ok test_edges (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R edges ... ok test_settings (tests.TestCase_YaesuFT2900R1900R) Testing Yaesu FT-2900R/1900R settings ... ok test_banks (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 brute force ... ok test_clone (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 clone ... ok test_copy_all (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 copy all ... ok test_detect (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 detect ... ok test_edges (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 edges ... ok test_settings (tests.TestCase_YaesuFTM350) Testing Yaesu FTM-350 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D brute force ... ok test_clone (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D clone ... ok test_copy_all (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D copy all ... ok test_detect (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D detect ... ok test_edges (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D edges ... ok test_settings (tests.TestCase_YaesuFT450D) Testing Yaesu FT-450D settings ... ok test_banks (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus brute force ... ok test_clone (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus clone ... ok test_copy_all (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus copy all ... ok test_detect (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus detect ... ok test_edges (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus edges ... ok test_settings (tests.TestCase_BoblovX3Plus) Testing Boblov X3Plus settings ... ok test_banks (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 brute force ... ok test_clone (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 clone ... ok test_copy_all (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 copy all ... ok test_detect (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 detect ... ok test_edges (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 edges ... ok test_settings (tests.TestCase_BTECHUV25X2) Testing BTECH UV-25X2 settings ... ok test_banks (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 brute force ... ok test_clone (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 clone ... ok test_copy_all (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 copy all ... ok test_detect (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 detect ... ok test_edges (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 edges ... ok test_settings (tests.TestCase_VertexStandardVXA700) Testing Vertex Standard VXA-700 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_PuxingPX777) Testing Puxing PX-777 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_PuxingPX777) Testing Puxing PX-777 brute force ... ok test_clone (tests.TestCase_PuxingPX777) Testing Puxing PX-777 clone ... ok test_copy_all (tests.TestCase_PuxingPX777) Testing Puxing PX-777 copy all ... ok test_detect (tests.TestCase_PuxingPX777) Testing Puxing PX-777 detect ... ok test_edges (tests.TestCase_PuxingPX777) Testing Puxing PX-777 edges ... ok test_settings (tests.TestCase_PuxingPX777) Testing Puxing PX-777 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_IcomICT7H) Testing Icom IC-T7H banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICT7H) Testing Icom IC-T7H brute force ... ok test_clone (tests.TestCase_IcomICT7H) Testing Icom IC-T7H clone ... ok test_copy_all (tests.TestCase_IcomICT7H) Testing Icom IC-T7H copy all ... ok test_detect (tests.TestCase_IcomICT7H) Testing Icom IC-T7H detect ... ok test_edges (tests.TestCase_IcomICT7H) Testing Icom IC-T7H edges ... ok test_settings (tests.TestCase_IcomICT7H) Testing Icom IC-T7H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFTM7250D) Testing Yaesu FTM-7250D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFTM7250D) Testing Yaesu FTM-7250D brute force ... ok test_clone (tests.TestCase_YaesuFTM7250D) Testing Yaesu FTM-7250D clone ... ok test_copy_all (tests.TestCase_YaesuFTM7250D) Testing Yaesu FTM-7250D copy all ... ok test_detect (tests.TestCase_YaesuFTM7250D) Testing Yaesu FTM-7250D detect ... ok test_edges (tests.TestCase_YaesuFTM7250D) Testing Yaesu FTM-7250D edges ... ok test_settings (tests.TestCase_YaesuFTM7250D) Testing Yaesu FTM-7250D settings ... skipped 'Settings not supported' test_banks (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR banks ... ok test_brute_force (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR brute force ... ok test_clone (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR clone ... ok test_copy_all (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR copy all ... ok test_detect (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR detect ... ok test_edges (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR edges ... ok test_settings (tests.TestCase_YaesuFT4VR) Testing Yaesu FT-4VR settings ... ok test_banks (tests.TestCase_CRTMicronUV) Testing CRT Micron UV banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_CRTMicronUV) Testing CRT Micron UV brute force ... ok test_clone (tests.TestCase_CRTMicronUV) Testing CRT Micron UV clone ... ok test_copy_all (tests.TestCase_CRTMicronUV) Testing CRT Micron UV copy all ... ok test_detect (tests.TestCase_CRTMicronUV) Testing CRT Micron UV detect ... ok test_edges (tests.TestCase_CRTMicronUV) Testing CRT Micron UV edges ... ok test_settings (tests.TestCase_CRTMicronUV) Testing CRT Micron UV settings ... skipped 'Settings not supported' test_banks (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G banks ... ok test_brute_force (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G brute force ... ok test_clone (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G clone ... ok test_copy_all (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G copy all ... ok test_detect (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G detect ... ok test_edges (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G edges ... ok test_settings (tests.TestCase_KenwoodTK760G) Testing Kenwood TK-760G settings ... ok test_banks (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 brute force ... ok test_clone (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 clone ... ok test_copy_all (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 copy all ... ok test_detect (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 detect ... ok test_edges (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 edges ... ok test_settings (tests.TestCase_WACCOMMINI8900) Testing WACCOM MINI-8900 settings ... ok test_banks (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE banks ... ok test_brute_force (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE brute force ... ok test_clone (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE clone ... ok test_copy_all (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE copy all ... ok test_detect (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE detect ... ok test_edges (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE edges ... ok test_settings (tests.TestCase_YaesuFT4XE) Testing Yaesu FT-4XE settings ... ok test_banks (tests.TestCase_IcomICT8A) Testing Icom IC-T8A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICT8A) Testing Icom IC-T8A brute force ... ok test_clone (tests.TestCase_IcomICT8A) Testing Icom IC-T8A clone ... ok test_copy_all (tests.TestCase_IcomICT8A) Testing Icom IC-T8A copy all ... ok test_detect (tests.TestCase_IcomICT8A) Testing Icom IC-T8A detect ... ok test_edges (tests.TestCase_IcomICT8A) Testing Icom IC-T8A edges ... ok test_settings (tests.TestCase_IcomICT8A) Testing Icom IC-T8A settings ... skipped 'Settings not supported' test_banks (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 brute force ... ok test_clone (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 clone ... ok test_copy_all (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 copy all ... ok test_detect (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 detect ... ok test_edges (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 edges ... ok test_settings (tests.TestCase_WouxunKG816) Testing Wouxun KG-816 settings ... ok test_banks (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR banks ... ok test_brute_force (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR brute force ... ok test_clone (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR clone ... ok test_copy_all (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR copy all ... ok test_detect (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR detect ... ok test_edges (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR edges ... ok test_settings (tests.TestCase_YaesuFT4XR) Testing Yaesu FT-4XR settings ... ok test_banks (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 brute force ... ok test_clone (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 clone ... ok test_copy_all (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 copy all ... ok test_detect (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 detect ... ok test_edges (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 edges ... ok test_settings (tests.TestCase_KenwoodTK8102) Testing Kenwood TK-8102 settings ... ok test_banks (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 brute force ... ok test_clone (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 clone ... ok test_copy_all (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 copy all ... ok test_detect (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 detect ... ok test_edges (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 edges ... ok test_settings (tests.TestCase_YaesuFT50) Testing Yaesu FT-50 settings ... ok test_banks (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K brute force ... ok test_clone (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K clone ... ok test_copy_all (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K copy all ... ok test_detect (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K detect ... ok test_edges (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K edges ... ok test_settings (tests.TestCase_PuxingPX888K) Testing Puxing PX-888K settings ... ok test_banks (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 banks ... ok test_brute_force (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 brute force ... ok test_clone (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 clone ... ok test_copy_all (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 copy all ... ok test_detect (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 detect ... ok test_edges (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 edges ... ok test_settings (tests.TestCase_IcomICV82U82) Testing Icom IC-V82/U82 settings ... skipped 'Settings not supported' test_banks (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 brute force ... ok test_clone (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 clone ... ok test_copy_all (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 copy all ... ok test_detect (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 detect ... ok test_edges (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 edges ... ok test_settings (tests.TestCase_WouxunKG818) Testing Wouxun KG-818 settings ... ok test_banks (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 brute force ... ok test_clone (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 clone ... ok test_copy_all (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 copy all ... ok test_detect (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 detect ... ok test_edges (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 edges ... ok test_settings (tests.TestCase_KenwoodTK8180) Testing Kenwood TK-8180 settings ... ok test_banks (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A brute force ... ok test_clone (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A clone ... ok test_copy_all (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A copy all ... ok test_detect (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A detect ... ok test_edges (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A edges ... ok test_settings (tests.TestCase_FeidaxinFD268A) Testing Feidaxin FD-268A settings ... ok test_banks (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 banks ... ok test_brute_force (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 brute force ... ok test_clone (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 clone ... ok test_copy_all (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 copy all ... ok test_detect (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 detect ... ok test_edges (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 edges ... ok test_settings (tests.TestCase_YaesuFT60) Testing Yaesu FT-60 settings ... ok test_banks (tests.TestCase_IcomICW32A) Testing Icom IC-W32A banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICW32A) Testing Icom IC-W32A brute force ... ok test_clone (tests.TestCase_IcomICW32A) Testing Icom IC-W32A clone ... ok test_copy_all (tests.TestCase_IcomICW32A) Testing Icom IC-W32A copy all ... ok test_detect (tests.TestCase_IcomICW32A) Testing Icom IC-W32A detect ... ok test_edges (tests.TestCase_IcomICW32A) Testing Icom IC-W32A edges ... ok test_settings (tests.TestCase_IcomICW32A) Testing Icom IC-W32A settings ... skipped 'Settings not supported' test_banks (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 brute force ... ok test_clone (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 clone ... ok test_copy_all (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 copy all ... ok test_detect (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 detect ... ok test_edges (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 edges ... ok test_settings (tests.TestCase_BTECHUV25X4) Testing BTECH UV-25X4 settings ... ok test_banks (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B brute force ... ok test_clone (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B clone ... ok test_copy_all (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B copy all ... ok test_detect (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B detect ... ok test_edges (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B edges ... ok test_settings (tests.TestCase_FeidaxinFD268B) Testing Feidaxin FD-268B settings ... ok test_banks (tests.TestCase_YaesuFT65E) Testing Yaesu FT-65E banks ... ok test_brute_force (tests.TestCase_YaesuFT65E) Testing Yaesu FT-65E brute force ... ok test_clone (tests.TestCase_YaesuFT65E) Testing Yaesu FT-65E clone ... ok test_copy_all (tests.TestCase_YaesuFT65E) Testing Yaesu FT-65E copy all ... ok test_detect (tests.TestCase_YaesuFT65E) Testing Yaesu FT-65E detect ... ok test_edges (tests.TestCase_YaesuFT65E) Testing Yaesu FT-65E edges ... ok test_settings (tests.TestCase_YaesuFT65E) Testing Yaesu FT-65E settings ... ok test_banks (tests.TestCase_IcomICW32E) Testing Icom IC-W32E banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomICW32E) Testing Icom IC-W32E brute force ... ok test_clone (tests.TestCase_IcomICW32E) Testing Icom IC-W32E clone ... ok test_copy_all (tests.TestCase_IcomICW32E) Testing Icom IC-W32E copy all ... ok test_detect (tests.TestCase_IcomICW32E) Testing Icom IC-W32E detect ... ok test_edges (tests.TestCase_IcomICW32E) Testing Icom IC-W32E edges ... ok test_settings (tests.TestCase_IcomICW32E) Testing Icom IC-W32E settings ... skipped 'Settings not supported' test_banks (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 brute force ... ok test_clone (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 clone ... ok test_copy_all (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 copy all ... ok test_detect (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 detect ... ok test_edges (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 edges ... ok test_settings (tests.TestCase_WouxunKGUV6) Testing Wouxun KG-UV6 settings ... ok test_banks (tests.TestCase_QYTKT7900D) Testing QYT KT7900D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_QYTKT7900D) Testing QYT KT7900D brute force ... ok test_clone (tests.TestCase_QYTKT7900D) Testing QYT KT7900D clone ... ok test_copy_all (tests.TestCase_QYTKT7900D) Testing QYT KT7900D copy all ... ok test_detect (tests.TestCase_QYTKT7900D) Testing QYT KT7900D detect ... ok test_edges (tests.TestCase_QYTKT7900D) Testing QYT KT7900D edges ... ok test_settings (tests.TestCase_QYTKT7900D) Testing QYT KT7900D settings ... ok test_banks (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode brute force ... ok test_clone (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode clone ... ok test_copy_all (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode copy all ... ok test_detect (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode detect ... ok test_edges (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode edges ... ok test_settings (tests.TestCase_KenwoodTMD710GCloneMode) Testing Kenwood TM-D710G_CloneMode settings ... ok test_banks (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 brute force ... ok test_clone (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 clone ... ok test_copy_all (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 copy all ... ok test_detect (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 detect ... ok test_edges (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 edges ... ok test_settings (tests.TestCase_BTECHUV5001) Testing BTECH UV-5001 settings ... ok test_banks (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B brute force ... ok test_clone (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B clone ... ok test_copy_all (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B copy all ... ok test_detect (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B detect ... ok test_edges (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B edges ... ok test_settings (tests.TestCase_FeidaxinFD288B) Testing Feidaxin FD-288B settings ... ok test_banks (tests.TestCase_IcomID31A) Testing Icom ID-31A banks ... ok test_brute_force (tests.TestCase_IcomID31A) Testing Icom ID-31A brute force ... ok test_clone (tests.TestCase_IcomID31A) Testing Icom ID-31A clone ... ok test_copy_all (tests.TestCase_IcomID31A) Testing Icom ID-31A copy all ... ok test_detect (tests.TestCase_IcomID31A) Testing Icom ID-31A detect ... ok test_edges (tests.TestCase_IcomID31A) Testing Icom ID-31A edges ... ok test_settings (tests.TestCase_IcomID31A) Testing Icom ID-31A settings ... ok test_banks (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D brute force ... ok test_clone (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D clone ... ok test_copy_all (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D copy all ... ok test_detect (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D detect ... ok test_edges (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D edges ... ok test_settings (tests.TestCase_WouxunKGUV8D) Testing Wouxun KG-UV8D settings ... ok test_banks (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 brute force ... ok test_clone (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 clone ... ok test_copy_all (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 copy all ... ok test_detect (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 detect ... ok test_edges (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 edges ... ok test_settings (tests.TestCase_BTECHUV50X2) Testing BTECH UV-50X2 settings ... ok test_banks (tests.TestCase_IcomIC208H) Testing Icom IC-208H banks ... ok test_brute_force (tests.TestCase_IcomIC208H) Testing Icom IC-208H brute force ... ok test_clone (tests.TestCase_IcomIC208H) Testing Icom IC-208H clone ... ok test_copy_all (tests.TestCase_IcomIC208H) Testing Icom IC-208H copy all ... ok test_detect (tests.TestCase_IcomIC208H) Testing Icom IC-208H detect ... ok test_edges (tests.TestCase_IcomIC208H) Testing Icom IC-208H edges ... ok test_settings (tests.TestCase_IcomIC208H) Testing Icom IC-208H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_QYTKT8900D) Testing QYT KT8900D banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_QYTKT8900D) Testing QYT KT8900D brute force ... ok test_clone (tests.TestCase_QYTKT8900D) Testing QYT KT8900D clone ... ok test_copy_all (tests.TestCase_QYTKT8900D) Testing QYT KT8900D copy all ... ok test_detect (tests.TestCase_QYTKT8900D) Testing QYT KT8900D detect ... ok test_edges (tests.TestCase_QYTKT8900D) Testing QYT KT8900D edges ... ok test_settings (tests.TestCase_QYTKT8900D) Testing QYT KT8900D settings ... ok test_banks (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode brute force ... ok test_clone (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode clone ... ok test_copy_all (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode copy all ... ok test_detect (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode detect ... ok test_edges (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode edges ... ok test_settings (tests.TestCase_KenwoodTMD710CloneMode) Testing Kenwood TM-D710_CloneMode settings ... ok test_banks (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H brute force ... ok test_clone (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H clone ... ok test_copy_all (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H copy all ... ok test_detect (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H detect ... ok test_edges (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H edges ... ok test_settings (tests.TestCase_IcomIC2100H) Testing Icom IC-2100H settings ... skipped 'Settings not supported' test_banks (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode brute force ... ok test_clone (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode clone ... ok test_copy_all (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode copy all ... ok test_detect (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode detect ... ok test_edges (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode edges ... ok test_settings (tests.TestCase_KenwoodTS480CloneMode) Testing Kenwood TS-480_CloneMode settings ... ok test_banks (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 brute force ... ok test_clone (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 clone ... ok test_copy_all (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 copy all ... ok test_detect (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 detect ... ok test_edges (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 edges ... ok test_settings (tests.TestCase_RadioddityGA510) Testing Radioddity GA-510 settings ... ok test_banks (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 brute force ... ok test_clone (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 clone ... ok test_copy_all (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 copy all ... ok test_detect (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 detect ... ok test_edges (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 edges ... ok test_settings (tests.TestCase_BTECHUV50X3) Testing BTECH UV-50X3 settings ... ok test_banks (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode brute force ... ok test_clone (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode clone ... ok test_copy_all (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode copy all ... ok test_detect (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode detect ... ok test_edges (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode edges ... ok test_settings (tests.TestCase_KenwoodTS590SGCloneMode) Testing Kenwood TS-590SG_CloneMode settings ... ok test_banks (tests.TestCase_RadioddityR2) Testing Radioddity R2 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RadioddityR2) Testing Radioddity R2 brute force ... ok test_clone (tests.TestCase_RadioddityR2) Testing Radioddity R2 clone ... ok test_copy_all (tests.TestCase_RadioddityR2) Testing Radioddity R2 copy all ... ok test_detect (tests.TestCase_RadioddityR2) Testing Radioddity R2 detect ... ok test_edges (tests.TestCase_RadioddityR2) Testing Radioddity R2 edges ... ok test_settings (tests.TestCase_RadioddityR2) Testing Radioddity R2 settings ... ok test_banks (tests.TestCase_IcomID51) Testing Icom ID-51 banks ... ok test_brute_force (tests.TestCase_IcomID51) Testing Icom ID-51 brute force ... ok test_clone (tests.TestCase_IcomID51) Testing Icom ID-51 clone ... ok test_copy_all (tests.TestCase_IcomID51) Testing Icom ID-51 copy all ... ok test_detect (tests.TestCase_IcomID51) Testing Icom ID-51 detect ... ok test_edges (tests.TestCase_IcomID51) Testing Icom ID-51 edges ... ok test_settings (tests.TestCase_IcomID51) Testing Icom ID-51 settings ... ok test_banks (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV brute force ... ok test_clone (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV clone ... ok test_copy_all (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV copy all ... ok test_detect (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV detect ... ok test_edges (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV edges ... ok test_settings (tests.TestCase_LUITONLT725UV) Testing LUITON LT-725UV settings ... ok test_banks (tests.TestCase_RadtelT18) Testing Radtel T18 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RadtelT18) Testing Radtel T18 brute force ... ok test_clone (tests.TestCase_RadtelT18) Testing Radtel T18 clone ... ok test_copy_all (tests.TestCase_RadtelT18) Testing Radtel T18 copy all ... ok test_detect (tests.TestCase_RadtelT18) Testing Radtel T18 detect ... ok test_edges (tests.TestCase_RadtelT18) Testing Radtel T18 edges ... ok test_settings (tests.TestCase_RadtelT18) Testing Radtel T18 settings ... ok test_banks (tests.TestCase_RetevisRT21) Testing Retevis RT21 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT21) Testing Retevis RT21 brute force ... ok test_clone (tests.TestCase_RetevisRT21) Testing Retevis RT21 clone ... ok test_copy_all (tests.TestCase_RetevisRT21) Testing Retevis RT21 copy all ... ok test_detect (tests.TestCase_RetevisRT21) Testing Retevis RT21 detect ... ok test_edges (tests.TestCase_RetevisRT21) Testing Retevis RT21 edges ... ok test_settings (tests.TestCase_RetevisRT21) Testing Retevis RT21 settings ... ok test_banks (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus banks ... ok test_brute_force (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus brute force ... ok test_clone (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus clone ... ok test_copy_all (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus copy all ... ok test_detect (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus detect ... ok test_edges (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus edges ... ok test_settings (tests.TestCase_IcomID51Plus) Testing Icom ID-51 Plus settings ... ok test_banks (tests.TestCase_RetevisRT22) Testing Retevis RT22 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT22) Testing Retevis RT22 brute force ... ok test_clone (tests.TestCase_RetevisRT22) Testing Retevis RT22 clone ... ok test_copy_all (tests.TestCase_RetevisRT22) Testing Retevis RT22 copy all ... ok test_detect (tests.TestCase_RetevisRT22) Testing Retevis RT22 detect ... ok test_edges (tests.TestCase_RetevisRT22) Testing Retevis RT22 edges ... ok test_settings (tests.TestCase_RetevisRT22) Testing Retevis RT22 settings ... ok test_banks (tests.TestCase_RetevisRT23) Testing Retevis RT23 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT23) Testing Retevis RT23 brute force ... ok test_clone (tests.TestCase_RetevisRT23) Testing Retevis RT23 clone ... ok test_copy_all (tests.TestCase_RetevisRT23) Testing Retevis RT23 copy all ... ok test_detect (tests.TestCase_RetevisRT23) Testing Retevis RT23 detect ... ok test_edges (tests.TestCase_RetevisRT23) Testing Retevis RT23 edges ... ok test_settings (tests.TestCase_RetevisRT23) Testing Retevis RT23 settings ... ok test_banks (tests.TestCase_IcomID800H) Testing Icom ID-800H banks ... ok test_brute_force (tests.TestCase_IcomID800H) Testing Icom ID-800H brute force ... ok test_clone (tests.TestCase_IcomID800H) Testing Icom ID-800H clone ... ok test_copy_all (tests.TestCase_IcomID800H) Testing Icom ID-800H copy all ... ok test_detect (tests.TestCase_IcomID800H) Testing Icom ID-800H detect ... ok test_edges (tests.TestCase_IcomID800H) Testing Icom ID-800H edges ... ok test_settings (tests.TestCase_IcomID800H) Testing Icom ID-800H settings ... ok test_banks (tests.TestCase_RetevisRT26) Testing Retevis RT26 banks ... skipped 'Banks not supported' test_brute_force (tests.TestCase_RetevisRT26) Testing Retevis RT26 brute force ... ok test_clone (tests.TestCase_RetevisRT26) Testing Retevis RT26 clone ... ok test_copy_all (tests.TestCase_RetevisRT26) Testing Retevis RT26 copy all ... ok test_detect (tests.TestCase_RetevisRT26) Testing Retevis RT26 detect ... ok test_edges (tests.TestCase_RetevisRT26) Testing Retevis RT26 edges ... ok test_settings (tests.TestCase_RetevisRT26) Testing Retevis RT26 settings ... ok ---------------------------------------------------------------------- Ran 1001 tests in 399.229s OK (skipped=141) struct memory { bbcd rx_freq[4]; bbcd tx_freq[4]; lbcd rx_tone[2]; lbcd tx_tone[2]; u8 unknown10:5, highpower:1, unknown11:2; u8 unknown20:4, narrow:1, unknown21:3; u8 unknown31:1, scanadd:1, unknown32:6; u8 unknown4; }; struct name { char name[7]; }; #seekto 0x0010; struct memory channels[128]; #seekto 0x08C0; struct name names[128]; #seekto 0x2020; struct memory vfo1; struct memory vfo2; style create: /chirp/.tox/style style installdeps: pep8==1.6.2, future style inst: /chirp/.tox/.tmp/package/1/chirp-0.3.0dev.zip style installed: DEPRECATION: Python 2.7 will reach the end of its life on January 1st, 2020. Please upgrade your Python as Python 2.7 won't be maintained after that date. A future version of pip will drop support for Python 2.7.,chirp==0.3.0.dev0,configparser==3.7.4,contextlib2==0.5.5,filelock==3.0.12,future==0.15.2,importlib-metadata==0.18,Mako==1.0.3,MarkupSafe==0.23,mercurial==3.7.3,packaging==19.0,pathlib2==2.3.4,pep8==1.6.2,pluggy==0.12.0,py==1.8.0,pygobject==3.20.0,pyparsing==2.4.0,pyserial==3.0.1,scandir==1.10.0,six==1.12.0,toml==0.10.0,tox==3.13.2,virtualenv==16.6.1,zipp==0.5.2 style run-test-pre: PYTHONHASHSEED='526238362' style run-test: commands[0] | python ./tools/cpep8.py ___________________________________ summary ____________________________________ unit: commands succeeded driver: commands succeeded style: commands succeeded congratulations :) Email was triggered for: Success Sending email for trigger: Success

1 0

[chirp_devel] [PATCH] [UV-6] Support Baofeng UV-6 without Auxiliary Block
by Jim Unroe 31 Aug '20

31 Aug '20

# HG changeset patch # User Jim Unroe <rock.unroe(a)gmail.com> # Date 1598909097 14400 # Mon Aug 31 17:24:57 2020 -0400 # Node ID fb0e42bb94ed2d8e95dac61ae38a86bb267d1019 # Parent da00bc273e5f52ea49e89e68819962413ca46e32 [UV-6] Support Baofeng UV-6 without Auxiliary Block This patch adds support for Baofeng radio models, including the UV-6, that do not support access to the auxiliary block of memory. Fixes #6567 diff -r da00bc273e5f -r fb0e42bb94ed chirp/drivers/uv5r.py --- a/chirp/drivers/uv5r.py Wed Aug 26 17:21:13 2020 -0400 +++ b/chirp/drivers/uv5r.py Mon Aug 31 17:24:57 2020 -0400 @@ -576,10 +576,11 @@ _do_status(radio, i) _do_status(radio, radio.get_memsize()) LOG.debug("done.") - LOG.debug("downloading aux block...") - # Auxiliary block starts at 0x1ECO (?) - for i in range(0x1EC0, 0x2000, 0x40): - data += _read_block(radio, i, 0x40, False) + if radio._aux_block: + LOG.debug("downloading aux block...") + # Auxiliary block starts at 0x1ECO (?) + for i in range(0x1EC0, 0x2000, 0x40): + data += _read_block(radio, i, 0x40, False) if append_model: data += radio.MODEL.ljust(8) @@ -650,6 +651,9 @@ "of the radio (%s).") raise errors.RadioError(msg % (image_version, radio_version)) + if not radio._aux_block: + image_matched_radio = True + # Main block for start_addr, end_addr in ranges_main: for i in range(start_addr, end_addr, 0x10): @@ -716,6 +720,7 @@ _vhf_range = (136000000, 174000000) _220_range = (220000000, 260000000) _uhf_range = (400000000, 520000000) + _aux_block = True _tri_power = False _mem_params = (0x1828 # poweron_msg offset ) @@ -1297,30 +1302,30 @@ # Old image, without aux block return group - other = RadioSettingGroup("other", "Other Settings") - group.append(other) - - def _filter(name): - filtered = "" - for char in str(name): - if char in chirp_common.CHARSET_ASCII: - filtered += char - else: - filtered += " " - return filtered + if self.MODEL != "UV-6": + other = RadioSettingGroup("other", "Other Settings") + group.append(other) - _msg = self._memobj.firmware_msg - val = RadioSettingValueString(0, 7, _filter(_msg.line1)) - val.set_mutable(False) - rs = RadioSetting("firmware_msg.line1", "Firmware Message 1", val) - other.append(rs) + def _filter(name): + filtered = "" + for char in str(name): + if char in chirp_common.CHARSET_ASCII: + filtered += char + else: + filtered += " " + return filtered - val = RadioSettingValueString(0, 7, _filter(_msg.line2)) - val.set_mutable(False) - rs = RadioSetting("firmware_msg.line2", "Firmware Message 2", val) - other.append(rs) + _msg = self._memobj.firmware_msg + val = RadioSettingValueString(0, 7, _filter(_msg.line1)) + val.set_mutable(False) + rs = RadioSetting("firmware_msg.line1", "Firmware Message 1", val) + other.append(rs) - if self.MODEL != "UV-6": + val = RadioSettingValueString(0, 7, _filter(_msg.line2)) + val.set_mutable(False) + rs = RadioSetting("firmware_msg.line2", "Firmware Message 2", val) + other.append(rs) + _msg = self._memobj.sixpoweron_msg rs = RadioSetting("sixpoweron_msg.line1", "6+Power-On Message 1", RadioSettingValueString( @@ -1646,7 +1651,7 @@ RadioSettingValueInteger(0, 50, _settings.pttlt)) dtmf.append(rs) - if not self._is_orig(): + if not self._is_orig() and self._aux_block: service = RadioSettingGroup("service", "Service Settings") group.append(service) @@ -1827,6 +1832,7 @@ _idents = [UV5R_MODEL_UV6, UV5R_MODEL_UV6_ORIG ] + _aux_block = False def get_features(self): rf = BaofengUV5R.get_features(self)

1 0